Amber connect ACT400-m Bedienungsanleitung

Know your device

ACT 400-m Device view

Pinout

ACT 400-m 2x6 socket pinout

number

Pin name

Description

VCC (10-30) V DC (+)

Power supply (+10-30 V DC).

DOUT 3

Digital output, channel 3. Open collector output. Max.

0,5 A DC.

DIN 3 / AIN 2

Analog input, channel 2. Input range: 0-30 V DC / Digital

input, channel 3.

DIN 2-N / AIN 1

Digital input, channel 2, Negative input (ground sense),

Analog input, channel 1, Input range: 0-30 VDC.

DIN 1

Digital input, channel 1.

INPUT 6

TX EXT (LVCAN –TX).

GND (-)

Ground pin. (10-30) V DC (―)

DOUT 1

Digital output, channel 1. Open collector output. Max.

0,5 A DC.

DOUT 2

Digital output, channel 2. Open collector output. Max.

0,5 A DC.

1WIRE POWER

+3,8 V output for 1–Wire devices.

1WIRE DATA

Data for 1–Wire devices.

INPUT 5

RX EXT (LVCAN - RX).

ACT 400-m 2x6 socket pinout

Wiring scheme

ACT 400-m Wiring scheme

Set up your device

How to insert Micro-SIM card and connect the battery

Cover removal

Micro-SIM card insert

Battery connection

Attaching cover back

1. Gently remove ACT 400-m cover using plastic pry tool from both sides.

2. Insert Micro-SIM card as shown with PIN request disabled or read our Wiki how to enter it later in

Amber Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.

3. Connect battery as shown to device. Position the battery in place where it does not obstruct other

components.

4. After configuration, see “PC Connection (Windows)”, attach device cover back.

Mounting recommendations

•Connecting wires

1. Wires should be connected while the module is not plugged in.

2. Wires should be fastened to stable wires or other non-moving parts. Any heat emitting and/or

moving objects should be kept away from the wires.

3. There should be no exposed wires. If factory isolation was removed while connecting the wires,

the isolation material should be applied.

4. If the wires are placed in the exterior or in places where they can be damaged or exposed to

heat, humidity, dirt, etc., additional isolation should be applied and the wires should not be

loose.

5. Wires cannot be connected to the board computers or control units.

•Connecting power source

1. Be sure that after the car computer goes to sleep mode, power might be still available on the

power wires. Depending on the car model, this may happen in 5 to 30 minutes period.

2. When the module is connected, measure the voltage again to make sure it did not decrease.

3. It is recommended to connect to the main power cable in the fuse box.

4. 3 A, 125 V external fuse shall be used.

•Connecting ignition wire

1. Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.

2. Check if this is not an ACC wire (when key is in the first position, most of the vehicle

electronics are available).

3. Check if power is still available when you turn off any of vehicles devices.

4. Ignition is connected to the ignition relay output. As alternative, any other relay, which has power

output when ignition is on, may be chosen.

•Connecting ground wire

1. Ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.

2. If the wire is fixed with the bolt, the loop must be connected to the end of the wire.

3. For better contact scrub paint from the spot where loop is going to be connected.

LED indications

Navigation LED indications

Behaviour

Meaning

Permanently switched on

GNSS signal is not received

Blinking every second

Normal mode, GNSS is working

Off

GNSS is turned off because: Device is not working or Device

is in sleep mode

Blinking fast constantly

Device firmware is being flashed

Status LED indications

Behaviour

Meaning

Blinking every second

Normal mode

Blinking every two seconds

Sleep mode

Blinking fast for a short time

Modem activity

Off

Device is not working or Device is in boot mode

Characteristics

Basic characteristics

Module

Name

ACT 400-m

Technology

LTE CAT M1/NB-IoT/GSM/GPRS/GNSS/BLUETOOTH

GNSS

GPS, GLONASS, GALILEO, BEIDOU, QZSS, AGPS

Receiver

Tracking: 33

Tracking sensitivity

-165 dBM

Accuracy

< 3 m

Hot start

< 1 s

Warm start

< 25 s

Cold start

< 35 s

Cellular

Technology

LTE CAT M1/NB-IoT/GSM

2G bands

BG95: B2/B3/B5/B8

BG96: B2/B3/B5/B8

4G bands

BG95: LTE-FDD (CAT M1):

B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/

B28/B66/B85

LTE-FDD (CAT NB2):

B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B28/B66/

B71/B85 GSM: 850/900/1800/1900

BG96: LTE FDD:

B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B28

LTE TDD: B39 (for CAT M1 only)

Data transfer

BG95:

LTE: Max. 588Kbps (DL)/Max.1119Kbps (UL)

GPRS: Max. 107Kbps (DL)/Max. 85.6Kbps (UL)

BG96:

LTE: Max. 375Kbps (DL)/Max.375Kbps (UL)

GPRS: Max. 107Kbps (DL)/Max. 85.6Kbps (UL)

Transmit power

Class 4 for GSM850/900: 23±2dBm

Class 1 for GSM1800/1900: 20±2dBm

Class 3 for LTE-TDD: 23±2.7dBm

Class 3 for LTE-FDD: 23±2.7dBm

Data support

SMS (text/data)

Power

Input voltage range

10-30 V DC with overvoltage protection

Back-up battery

170 mAh Li-Ion battery 3.7 V (0.63 Wh)

Internal fuse

3 A, 125 V

Power consumption

At 12V < 3 mA (Ultra Deep Sleep)

At 12V < 5 mA (Deep Sleep)

At 12V < 11 mA (Online Deep Sleep)

At 12V < 18 mA (GPS Sleep)

At 12V < 34 mA (nominal with no load)

At 12V < 2A Max. (with full Load / Peak)

Bluetooth

Specification

4.0 + LE

Supported peripherals

Temperature and Humidity sensor, Headset, OBDII

dongle, Inateck Barcode Scanner, Universal BLE sensors

support

Interface

Digital Inputs

Negative Inputs

1 (Digital input 2)

Digital Outputs

Analog Inputs

CAN interfaces

1-Wire

GNSS antenna

Internal High Gain

GSM antenna

Internal High Gain

USB

2.0 Micro-USB

LED indication

2 status LED lights

SIM

Micro-SIM + eSIM

Memory

128MB internal flash memory

Physical specification

Dimensions

65 x 56 x 20,6 mm (L x W x H)

Weight

55 g

Operating environment

Operating temperature (without

battery)

-20 °C to +85 °C

Storage temperature (without battery)

-20 °C to +85 °C

Operating temperature (with battery)

-20 °C to +40 °C

Storage temperature (with battery)

-20 °C to +45 °C

Operating humidity

5% to 95% non-condensing

Ingress Protection Rating

IP41

Battery charge temperature

0 °C to +45 °C

Battery discharge temperature

-20 °C to +60 °C

Features

Sensors

Accelerometer

Scenarios

Green Driving, Over Speeding detection, Jamming

detection, GNSS Fuel Counter, DOUT Control Via Call,

Excessive Idling detection, Immobilizer, iButton Read

Notification, Unplug detection, Towing detection, Crash

detection, Auto Geofence, Manual Geofence, Trip, Ground

Sense

Sleep modes

GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep

Sleep

Configuration and firmware update

FOTA Web, FOTA, Amber Configurator (USB, Bluetooth),

FMBT mobile application (Configuration)

SMS

Configuration, Events, DOUT control, Debug

GPRS commands

Configuration, DOUT control, Debug

Time Synchronization

GPS, NITZ, NTP

Fuel monitoring

LLS (Analog), LV-CAN200, ALL-CAN300, CAN-

CONTROL, CAN-CONTROL, OBDII dongle

Ignition detection

Digital Input 1, Accelerometer, External Power Voltage,

Engine RPM (CAN Adapters, OBDII dongle)

Electrical characteristics

Characteristic description

Value

Min.

Typ.

Max.

Unit

Supply Voltage

Supply Voltage (Recommended

Operating Conditions)

+10

+30

Digital Output (Open Drain grade)

Drain current

(Digital Output OFF)

120

μA

Drain current (Digital Output

ON, Recommended Operating

Conditions)

0.1

0.5

Static Drain-Source resistance (Digital

Output ON)

400

600

mΩ

Digital Input

Input resistance (DIN1)

kΩ

Input resistance (DIN2)

38.45

kΩ

Input resistance (DIN3)

150

kΩ

Input voltage (Recommended Operating

Conditions)

Supply

voltage

Input Voltage threshold (DIN1)

7.5

Input Voltage threshold (DIN2)

2.5

Input Voltage threshold (DIN3)

2.5

Analog Input

Input voltage (Recommended Operating

Conditions), Range 1

+10

Input resistance, Range 1

38.45

kΩ

Measurement error on 12V,

Range 1

0.9

Additional error on 12 V,

Range 1

108

Measurement error on 30 V,

Range 1

0.33

Additional error on 30 V,

Range 1

Input Voltage (Recommended Operating

Conditions), Range 2

+30

Input resistance, Range 2

150

kΩ

Measurement error on 12 V,

Range 2

0.9

Additional error on 12 V,

Range 2

108

Measurement error on 30 V,

Range 2

0.33

Additional error on 30 V,

Range 2

Output Supply Voltage 1-Wire

Supply voltage

+4.5

+4.7

Output inner resistance

Output current (Uout > 3.0 V)

Short circuit current (Uout = 0)

NEGATIVE INPUT

Input resistance

38.45

kΩ

Input voltage (Recommended Operating

Conditions)

Supply

voltage

Input voltage threshold

0.5

Sink current

180

Safety information

This message contains information on how to operate ACT 400-m safely. By following these

requirements and recommendations, you will avoid dangerous situations. You must read

these instructions carefully and follow them strictly before operating the device!

•The device uses SELV limited power source. The nominal voltage is +12 V DC. The

allowed voltage range is +10...+30 V DC.

•To avoid mechanical damage, it is advised to transport the device in an impact-proof

package. Before usage, the device should be placed so that its LED indicators are

visible. They show the status of device operation.

•When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the

vehicle power supply should be disconnected.

•Before unmounting the device from the vehicle, the 2x6 connector must be

disconnected. The device is designed to be mounted in a zone of limited access, which is

inaccessible to the operator. All related devices must meet the requirements of EN

60950-1 standard. The device ACT 400-m is not designed as a navigational device for

boats.

Do not disassemble the device. If the device is damaged, the power supply cables

are not isolated or the isolation is damaged, DO NOT touch the device before

unplugging the power supply.

All wireless data transferring devices produce interference that may affect other

devices which are placed nearby.

The device must be connected only by qualified personnel.

The device must be firmly fastened in a predefined location.

The programming must be performed using a PC with autonomic power supply.

Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity.

Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.

Battery should not be disposed of with general household waste. Bring damaged

or worn-out batteries to your local recycling center or dispose them to battery

recycle bin found in stores.

Certification and Approvals



•ACT 400-m EAC

•ACT 400-m REACH

•ACT 400-m Declaration of IMEI assignment

•ACT 400-m CE / RED

•ACT 400-m E-Mark

•ACT 400-m RoHS

•ACT 400-m Declaration of device operation temperature

This sign on the package means that it is necessary to read the User‘s Manual

before your start using the device. Full User‘s Manual version can be found in our

Wiki.

This sign on the package means that all used electronic and electric equipment

should not be mixed with general household waste.

Hereby, Amber declare under our sole responsibility that the above described

product is in conformity with the relevant Community harmonization: European

Directive 2014/53/EU (RED).

17 Warranty

Amber guarantees its products to be free of any manufacturing defects for a period of 24

months. With additional agreement we can agree on a different warranty period, for more detailed

information please contact our sales manager.

All batteries carry a reduced 6 month warranty period.

If a product should fail within this specific warranty time, the product can be:

•Repaired

•Replaced with a new product

•Replaced with an equivalent repaired product fulfilling the same functionality

•Amber can also repair products that are out of warranty at an agreed cost.

Warranty Disclaimer

Amber products are intended to be used by persons with training and experience. Any other use

renders the limited warranties expressed herein and all implied warranties null and void and same are

hereby excluded. also excluded from this limited warranty are any and all incidental or consequential

damages including but not limited to, loss of use or revenue, loss of time, inconvenience or any other

economic loss.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere amber connect Touch-Terminal Handbücher

amber connect

amber connect Amber Govern T400-la Bedienungsanleitung

amber connect

amber connect Amber Vision C400 Bedienungsanleitung

amber connect

amber connect Covert C411 Bedienungsanleitung

amber connect

amber connect Insight T210 Bedienungsanleitung

amber connect

amber connect Amber Covert T200 Bedienungsanleitung

amber connect

amber connect ACC410-E/LA Bedienungsanleitung

amber connect

amber connect ACT200 Bedienungsanleitung

amber connect

amber connect Covert T300 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

amber connect ACT400-m Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken