Ambient NanoLockit Fehlerbehebungshandbuch
QUICK
START
GUIDE
QUICK START GUIDE |
Green Button
Red Button
Micro USB:
charge and
external power
Charge time / operation:
15 min / 5 hrs
30 min / 10 hrs
2 hrs / 35 hrs (full)
ACN Antenna:
for wireless sync
with other Lockits
Lemo Connector:
TC (and metadata)
interface
Status LED
Power Button
Explanation
QUICK START GUIDE |
3
short
ca. 30 min left
Status LED Codes 1 sec 2 sec
ext. power, idle, charging
ext. power, idle, fully charged
int. power, lo bat
Generator Mode:
idle, no TC out, RTC lost
idle, no TC out, RTC OK
generator set, TC out
generator set, TC out, lo bat
generator set, TC level reduced
TRX Mode:
idle, no TC on input or ACN
TX (LTC/MTC via cable)
RX (LTC/MTC over ACN)
long
LED status overview
QUICK START GUIDE |
The example setup
Film Camera
NANOLOCKIT
DSLR Camera
NANOLOCKIT
Audio Recorder
NANOLOCKIT
TC OUT
TC IN
The goal: syncing
timecode (TC) and
frame rate (FPS).
TC 01:23:45:12
TC 01:23:45:12
TC 01:23:45:12
QUICK START GUIDE |
5
Timecode Cable*
Timecode Cable*
TC-IO-35RA (included)
*NOTE:
The specic cable
required is de-
pendent on the
connected device.
The most common
cables are:
• TC-IO-35RA
• TC-IO
• LTC-Out
• LTC-Out/Epic
Please check our
website.
QUICK START GUIDE |
Press the Power But-
ton on all NanoLockits
for 3 seconds until the
LED lights up green .
Then release and LEDs
start to ash.
1
Turn on all NanoLockits
NOTE:
To reset the unit to factory default, press
and hold for 10 seconds until LED lights
up red .
Ü
3 sec
QUICK START GUIDE |
7
TC
FPS
12:45:12:02
25 fps
The NanoLockit always starts with its
Real Time Clock (RTC) at last frame rate
or at default 25 FPS with output muted.
To activate the LEMO Output while
jamming other Lockits with this timecode
and frame rate, proceed with step 3.
To adjust the RTC and frame rate,
proceed with step 2A. To jam from an
external device, proceed with step 2B.
QUICK START GUIDE |
To set the RTC and the
frame rate, use the
LockitToolbox software
(PC and Mac, available at
nanolockit.com).
2A
RTC
Set the internal clock of the NanoLockit
micro USB
LockitToolbox
NOTE:
On start a valid RTC will be
indicated by LEDs ashing red/
green , a lost RTC by ashing
red .
QUICK START GUIDE |
9
micro USB
NANOLOCKIT
TC OUT
TC IN
To jam your NanoLockit
from an external de-
vice, connect them with
the appropriate time-
code cable. If succesful,
the LED will ash green
. Finish by dis-
connecting the cable.
2B
TC
FPS
TC 01:23:45:12
25 fps
External jamming sets the TC
and FPS while activating the
LEMO output.
QUICK START GUIDE |
Press the Green Button
for 3 seconds until LED
double blinks green:
.
This sets the TC and FPS,
wirelessly syncs all other
NanoLockits, and activa-
tes all LEMO outputs. If
successful, all units will
ash green in sync.
3
Ü
3 sec
TC & FPS
Andere Handbücher für NanoLockit
8
Inhaltsverzeichnis
Andere Ambient Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
