AMCON EQ-6002 Bedienungsanleitung

1-800-255-6161• Fax 1-800-397-0013

www.amconlabs.com

AMCON AUTOMATIC

CHART PROJECTOR

USER’S MANUAL

EQ-6002

Disclaimer............................................................................................................2

1. Introduction......................................................................................................3

2. Safety Instructions.............................................................. ............................3

3. Charts and Specifications........................................... ...................................4

4. Parts of the Instrument................................................................. ..................6

4.1 Projector Parts....................................................................................6

4.2 Remote Control Parts.........................................................................6

5. Operating Procedures ....................................................................................7

5.1 Preparation .........................................................................................7

5.2 Operation of the Remote Control......................................................7

5.3 Using the Program Function............................................ .................8

6. Maintenance and Care.......................................................... ..........................9

6.1 Daily Maintenance..............................................................................9

6.2 Replacing the Bulb.............................................................................9

6.3 Replacing the Fuse. ...........................................................................9

6.4 Changing the Channel Setting of the Remote Control.................. 10

7. Troubleshooting............................................................................................11

Automatic Chart Projector - EQ-6002

________________________________________________________________

DISCLAIMER

Amcon, The Eyecare Supply Center makes no representations or warranties,

either expressed or implied, with respect to the contents hereof and specifically

disclaims any warranties, merchantability, or fitness for any particular purpose.

Further, Amcon, The Eyecare Supply Center reserves the right to revise this

publication and to make changes from time to time in the contents hereof without

obligation of this company to notify any person of such revision or changes.

Automatic Chart Projector - EQ-6002

________________________________________________________________

1. Introduction

Thank you for purchasing the Amcon Automatic Chart Projector. Please read

this instruction manual and keep it in a convenient location for future reference.

The remote controlled Amcon Automatic Chart Projector is used to test visual

acuity. The Amcon Automatic Chart Projector provides operational convenience

in a high quality instrument.

2. Safety Instructions

To ensure safe usage of this product, it is important that you follow the

instructions in this manual as well as the warning notices on the instrument.

•Do not look directly into the projector lens during operation. The intense

light beam may be harmful to your eyes.

•To avoid damage, always place this device on a stable stand. This

instrument is not designed to sustain rough treatment or falls.

•To reduce the risk of electric shock, do not disassemble this projector.

Take it to a qualified technician when service or repair is required.

Incorrect reassembly can cause malfunction of the projector or electric

shock when the appliance is subsequently used.

•Never attempt to replace the bulb or any electronic component unless the

instrument is unplugged from the power source.

•

Always open the lens shutter or remove the lens cap prior to turning on

the projector lamp.

•Avoid placing this projector in the following environments:

oPoorly ventilated or confined locations. Place at least 2 inches (5

cm) from walls and allow free flow of air around the projector.

oLocations where temperatures may become excessively high, over

90°F (32°C).

oLocations with excessive humidity, dust, or cigarette smoke.

•Do not place any objects on projector.

•Avoid placing liquids near the projector. If the projector does become wet,

immediately disconnect it from the power source.

Automatic Chart Projector - EQ-6002

________________________________________________________________

3. Charts and Specifications

Letter Charts:

Tumbling E Charts:

Number Charts:

Picture Charts:

Worth Four Dot Chart: Astigmatic Chart:

Red / Green Charts:

Automatic Chart Projector - EQ-6002

________________________________________________________________

Binocular Vision Testing Charts:

Refraction distance 5 ft – 20 ft

Projection distance 5 ft – 20 ft

Projection magnification 30X (at 20 ft refraction)

Number of charts 30

Chart changeover 1 frame / 0.3 sec.

Mask changeover 1 frame / 0.1 sec.

Bulb 12V 50W (Halogen)

Replacement bulbs available from Amcon

Product number: RQ-6200

Electricity AC 110V 60Hz

Power consumption 80W

Weight 13 lbs. 3 ounces (6.0 Kg)

Dimensions 11 7/8” x 9” x 9 ½” (30 cm X 23 cm X 24 cm)

Automatic Chart Projector - EQ-6002

________________________________________________________________

4. Parts of the Instrument

4.1 Projector Parts

1) Top Cover

2) Remote Sensor

3) Front Panel

4) Lamp Cover

5) Barrel Screw

6) Projection Window

7) Base

8) Power Switch

9) Power Socket

4.2 Remote Control Parts

1) Remote Signal Emitter

2) Chart Switches

3) Light Switch

4) Reset Switch

5) Program Forward Switch

6) Program Back Switch

7) Highlight Selectors

8) Highlight Transfer Selectors

9) R/G switch

10) Program switch

Automatic Chart Projector - EQ-6002

________________________________________________________________

5. Operating Procedures

Caution: Do not tilt the projector or place in an unstable place. The projector

may topple over, drop or cause injury.

Warning: Connect the power plug to a properly grounded three-prong AC outlet.

If it is connected to an ungrounded outlet, fire and/or electrical shock may result.

Caution: Handling the power plug with wet hands can cause electric shock.

5.1 Preparation

Place the instrument approximately level to the person to be tested. Turn the

power switch ‘off’. Insert the power cord into the power socket on the projector

body and plug into the wall outlet. Turn the power switch ‘on’. Remove the

battery cover from the back of the remote controller. Insert batteries into the

remote controller as illustrated and replace the battery cover. Adjust the position

of the projector so that the projector light is centered on the screen. Be sure the

projector is in the position from which it will be used. To focus the projector, slide

the focusing knob that is found on the underside of the projector base (on the

same side as the lamp cover). There is a barrel screw that must be loosened

before the knob can be moved. The enclosed Allen wrench can be used to

loosen or tighten this screw.

5.2 Operation of the Remote Control

Turn the projector’s power switch on. The chart will automatically reset to the

start position and the lamp will light. When using the remote controller, point the

remote signal emitter in the direction of the remote sensor on the front of the

projector. The switch functions are as follows:

a) Chart Switches - Projects the indicated chart on the switch

b) Light Switch - Turns the lamp off and on

c) Reset Switch - Returns to chart 1 of the program

d) Program Forward Switch - Fowards the program automatically

e) Program Back Switch - Reverses the program automatically

f) Highlight Selector - Isolates chart characters

g) Highlight Transfer Selectors - Moves the isolation of the characters in

the direction indicated. (When the highlighted area of a chart being

projected advances to the maximum or minimum on that chart, the

next or previous chart in the sequence will automatically appear.

Charts can be switched within the same type.)

h) R&G Switch - Applies the R&G filters to the designated charts

i) Program Switch - Refer to the Program Procedure, section 5.3, for

using this function

Note: The projector will automatically turn off if not in use for 5 minutes.

Automatic Chart Projector - EQ-6002

________________________________________________________________

5.3 Using the Program Function

Accessing the Programming Mode

a) Turn on the power switch. The projector goes into initialization state.

b) Press the “RESET” button on the remote control.

c) Press the “R and G filter” button on the remote control.

d) Press the “Reset” button again on the remote control. The projector

will beep twice after pressing each button in “1b, 1c, 1d”. After the

third button, the projector will be in programming mode. At any time

up to step “d”, pressing any other button will return the projector to

normal operating state.

Select Program 1 or 2

Press the “P1/P2” switch to select program 1 or 2. The beeper will sound

once if program 1 is selected and twice if program 2 is selected.

Selecting Charts for the Program

a) Press the “program up” button to open the position for the first chart.

b) Select the desired chart button along with the desired “highlight”

button.

c) Press the “program up” button again to enter the selection and move

to open the next position of the program. The beeper will sound four

times. Repeat steps 3a, 3b, 3c to enter other charts. Up to 30

selections are possible.

Completing the Program

a) When finished entering, press the “Reset” button to exit.

b) Press the light switch to turn off the projector.

Using the Program

a) To use a program, select program P1 or P2 by pressing the “P1/P2”

button. The beeper will indicate the program selected by sounding

once for P1 and twice for P2.

b) Press the “Program Up” button to run the program. The “Program Up”

and “Program Down” buttons will advance or reverse the program.

Automatic Chart Projector - EQ-6002

________________________________________________________________

6. Maintenance and Care

6.1 Daily Maintenance

•Cover the projector when not in use. This instrument is sensitive to dust

contamination.

•Turn the power switch off when not in use. It is also recommended to

unplug this instrument when not in use for longer periods of time.

•Keep projector clean by wiping the outside panels with a dry cloth. To

remove more difficult stains, a damp cloth with a mild detergent may be

used. A mild glass cleaner may be used on the outside panels. Be

careful not to dampen the inside parts of the projector.

•

When the lens is dirty, wipe it lightly with a good quality, dry microfiber

cloth. An Amcon Vista Cham is recommended.

6.2 Replacing the Bulb

Caution: To avoid electric shock, unplug the power cable when replacing the

projection lamp.

Caution: Do not replace the projection lamp immediately after turning off the

light. The lamp may still be hot and could lead to burns.

Turn the power switch off. Remove the lamp cover screw and remove the cover.

Remove the lamp attaching screw, hold the socket and remove the lamp. Hold

the socket and the lamp flange and remove the lamp from the socket. Install the

new lamp securely. Make sure you install it in the correct direction. Do not touch

the glass of the bulb directly with your fingers. If the bulb is touched by accident,

wipe the fingerprint off with alcohol. Replacement bulbs are available from

Amcon Product number: RQ-6200. Match the protruded part of the lamp

attaching area with the lamp flange notch and tighten with the lamp attaching

screw to secure the lamp. Place the lamp cover on. Turn the power switch on.

Make a trial projection to check that there is no illumination irregularity. If there is

any irregularity, turn the power off again and check that the lamp is properly

installed.

6.3 Replacing the Fuse

Warning: Unplug the power cable before removing the fuse cover to replace the

fuse. Removing the fuse cover with the power cable plugged in can cause

electric shock.

Warning: Use only attaching fuses (250 v, 1A). Using other fuses may cause a

fire in the event that the instrument fails.

Andere Handbücher für EQ-6002

Inhaltsverzeichnis

Andere AMCON Projektor Handbücher

AMCON

AMCON EQ-6002 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung