AMD DIrect Pro Series Bedienungsanleitung

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS

DO NOT ATTEMPT TO INSTALL OR OPERATE THIS APPLIANCE

DO NOT DISCARD. THIS MANUAL

HAS IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS.

LEAVE WITH THE HOMEOWNER.

MODEL:

SERIAL #:

Warning: For Outdoor Use Only

Installation and Operating Instructions

Outdoor Pro Brass Snowake Burners & Kits

INSTALLATION PRECAUTION:

This system requires a minimum 18 square inches (per side) of cross ventilation.

Failure to provide proper ventilation will void the warranty.

PN#90403

“PRO SERIES”

Burner Only Description Burner Kit Description Input Rating

FG-PSBR-SF11-NG

FG-PSBR-SF11-LP 11” Burner Only FG-PSBR-SF11-NGK

FG-PSBR-SF11-LPK 11” Burner Kit 50,000 Btu’s

42,000 Btu’s

FG-PSBR-SF18-NG

FG-PSBR-SF18-LP 18” Burner Only FG-PSBR-SF18-NGK

FG-PSBR-SF18-LPK 18” Burner Kit 145,000 Btu’s

124,000 Btu’s

FG-PSBR-SF25-NG

FG-PSBR-SF25-LP 25” Burner Only FG-PSBR-SF25-NGK

FG-PSBR-SF25-LPK 25” Burner Kit 260,000 Btu’s

240,000 Btu’s

FG-PSBR-SF32-NG

FG-PSBR-SF32-LP 32” Burner Only FG-PSBR-SF32-NGK

FG-PSBR-SF32-LPK 32” Burner Kit 426,000 Btu’s

402,000 Btu’s

Note: NG = Natural Gas and LP = Liquid Propane Gas

These re pits are manufactured from the factory as Natural or Propane Gas.

These are not convertible from one gas to another. Ensure you order the proper gas type before installing.

11” Burner

18” Burner

25” Burner

32” Burner

REV. A Page 2

Pro Snowake Burners and Burner Kits

Fuels used in gas red appliances, and the products of combustion such as fuels, contain

chemicals known to cause cancer, birth defects and/or other reproductive harm.

This warning is issued pursuant to the California Health & Safety Code Sec. 25249.1

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide

which has no odor.

Using it in an enclosed area can kill you.

Never use this appliance in an enclosed

space such as a camper, tent, car or home.

WARNING

Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or other appliance.

An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

WARNING

Do not leave unattended during use.

Do not use for cooking.

Follow all gas leak procedures in this

manual prior to operation.

WARNING

Improper installation, adjustment,

alteration, service or maintenance

can cause injury or property damage,

personal injury of loss of life

Read the owner’s information manual

provided with this appliance.

Installation and service must be

performed by a qualied installer,

service agency, or the gas supplier.

WARNING

If the information in this manual is not

followed exactly, a re or explosion

may result causing property damage,

personal injury, or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or other appliances.

If you smell gas:

1. Shut off gas to the appliance

2. Extinguish any open ame.

3. If odor continues, leave the area

immediately.

4. After leaving the area, call your gas

supplier or re department.

DANGER

FIRE OR EXPLOSION

HAZARD

REV. A Page 3

Pro Snowake Burners and Burner Kits

Specications 4-5

Preparation for Non-Combustible Structure 6

Hard Piping to Fire Pit 6

High Elevation 6

Cross Ventilation Requirements 6

Media Requirements 6

Pipe Sizing Chart 7

Installation into an Approved Enclosure 8

Burner Information 9

Burner Assembly 9

Installing Key Valve 10

Typical Installation Drawings 11

Operation 12

Lighting Instructions 12

Replacement Parts 13

Replacement Parts List 14

Fire Pit Maintenance/ Trouble Shooting 15

Pro Burner Contents 15

Optional Accessories 16

TABLE OF CONTENTS

All media (i.e. lava rock, lava stones, lava boulders and fire glass) has the potential of

thermal spalling. This is a process that may occur when media is wet and moisture gets

trapped inside of the material due to rapid temperature differences. When this happens

the media has the potential to crack or “pop” outside the fire feature.

WE HIGHLY RECOMMEND COVERING ALL FIRE FEATURES WHEN NOT IN USE

The use of a cover can lessen the impact of thermal spalling; however, heavy rains, high

humidity and the presence of moisture may still cause the media to pop.

ALWAYS USE CAUTION WHEN USING THE FIRE FEATURE

Extra caution should be taken when lighting a fire feature when heavy rains, high humidity

and moisture are present. Light the fire feature; leave the area allowing any moisture in

the media to dissipate. We strongly recommend that during this drying out time that you

monitor the fire feature from a distance. This drying out period should be no less than 30

minutes. Continue monitoring the flame from distance to ensure that all popping has

ceased before fully enjoying the fire.

CAUTION

CALIFORNIA PROPOSITION 65

WARNING

This product can expose you to Chromium, which is

known to the state of California to cause cancer

and birth defects or other reproductive harm.

(For more information, go to www.p65warnings.ca.gov)

Congratulations! You have just purchased a AMD Direct, Inc “Pro Series” Snowake Burner. These Brass

Burners come in four sizes, 11”, 18”, 25”, 32”, models. Each model is a single brass burner and incorporates

individual injectors that eliminate the need for one main burner orice. The 11” model incorporates 8 injectors

where up to the 32” model has 80 injectors. All models vary with the quantity of injectors. Injectors provide a

unique ame pattern that differs from a typical steel burner.

REV. A Page 4

Pro Snowake Burners and Burner Kits

SPECIFICATIONS

Table 1 Installation specications. Note: Add “K” after the model number to order a “KIT”.

NG Models: #

Injectors

NG Injector

Size

NG Btu’s LP Models: LP Injector

Size

LP Btu’s

FG-PSBR-SF11-NG 8 #61 (0.039) 50K (14.65kW) FG-PSBR-SF11-LP #72 (0.025) 42K (12.30kW)

FG-PSBR-SF18-NG 24 #61 (0.039) 145K (42.49kW) FG-PSBR-SF18-LP #72 (0.025) 124K (36.34kW)

FG-PSBR-SF25-NG 48 #61 (0.039) 260K (76.19kW) FG-PSBR-SF25-LP #72 (0.025) 240K (70.33kW)

FG-PSBR-SF32-NG 80 #61 (0.039) 426K (124.84kW) FG-PSBR-SF32-LP #72 (0.025) 402K (117.81kW)

Table 2 Btu Specications. Note: Add “K” after the model number to order a “KIT”.

Models

Pro Burner Only or Pro Burner Kit Min. Pan

Depth

Burner

Size

Min. Inside

Pan Size

Combustible

Side Wall

Combustible

Ceiling

Combustible

Floor

FG-PSBR-SF11-NG / FG-PSBR-SF11-LP 2 ½” - 3” 11” 19” 36” 120” 18”

FG-PSBR-SF18-NG / FG-PSBR-SF18-LP 2 ½” - 3” 18” 25” 36” 120” 18”

FG-PSBR-SF25-NG / FG-PSBR-SF25-LP 2 ½” - 3” 25” 29” 36” 120” 18”

FG-PSBR-SF32-NG / FG-PSBR-SF32-LP 2 ½” - 3” 32” 33” 36” 120” 18”

Disclaimer: Btu listings are based on 7.0”WC for Natural Gas and 11.0”WC for Liquid Propane (LP)

at the burner orice. Flex line size and proper gas pipe sizing will also affect Btu’s. As a result your

Btu’s may vary slightly from Table 2 specications.

BEFORE INSTALLING A PRO SNOWFLAKE BURNER DETERMINE WHAT PAN WILL BE USED:

The Pro Burner Snowake models above are not provided with pans for installation. We suggest you provide an

appropriate non-combustible burner pan to install the Pro Burner. Burner pans sizes listed in Table 1 are suggested sizes

based on the burner model size. Pans should be square, rectangular or a at metal. NOTE: It is recommended to use

304 Stainless Steel. Burner pans should have ¼” drainage holes to prevent standing water in pan and the center hole

for the burner nipple should be ⅞” in diameter. A recommended material thickness for any burner pan or at disc is 16

gauge. Once the Burner is installed into a burner pan then proceed with this manual to complete the installation.

CAUTION: DO NOT use stiff screen or perforated metal as a burner pan. Some gases are heavier than air and

screen or perforated metal can enable the gas to ow down inside an enclosure which could cause delayed

ignitions or explosions.

Description: Pro Snowake-Burners only are provided with a brass burner and nipple (i.e. FG-PSBR-SF18-NG) and Pro

Burner Kits are provided with a Pro Snowake Burner, key valve assembly, ex line and nipple(i.e. FG-PSBR-SF18-NGK).

Note: No LP Conversion kits are available. You must order a specic LP or Natural Gas Burner,

Table 3 Gas Pressures

Pressure NG LP

Min. Inlet 3.5” WC (0.87 kPa) 8.0” WC (1.99kPa)

Max. Inlet 10.5” WC (2.61kPa) 13.0” WC (3.23 kPa)

Normal Inlet 7.0” WC (1.74 kPa) 11.0” WC (2.73 kPa)

CAUTION: No LP Conversion kits are available. You must order a specic LP or Natural Gas Burner,

REV. A Page 5

Pro Snowake Burners and Burner Kits

Fig. 1 Clearance to Combustibles for Table 1

(Not to be used in an enclosed space)

24”

Max

Overhang

(Center Line)

SPECIFICATIONS CONTINUED

All Pro Snowake Burners come ready to install and have a ½” male center nipple. The burner must be installed as

shown in Fig. 5 with center nipple facing downward. Ensure to seal each NPT tting with thread tape or pipe compound.

NOTE: Flared ttings do not require tape or compound.

Pro Snowake Burner Kit: Includes Brass Burner, nipple, ared tting, brass supports & hardware, manual key valve

with 12-inch key and 46” ex connector.

Pro Snowake Burner Only: Includes Brass Burner, nipple, ared tting, brass supports & hardware.

PRO Brass Snowake Burner Information

REV. A Page 6

Pro Snowake Burners and Burner Kits

IMPORTANT

Installation of Natural or LP gas should be done by a qualied installer, service agency or gas supplier.

This appliance must be isolated from the gas supply piping system by closing its manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than ½” psi (3.5kPa)

VENTILATION FOR NON-COMBUSTIBLE ENCLOSURE

Fire pits are subjected to many outdoor elements such as

rain, snow, wind, heat or cold. A minimum of 18 square

inches (opposite sides) of cross ventilation is required

to keep the components in good working order. Use

Figure 2 as guide to assist to incorporate proper ventilation.

Fig. 2 Cross Ventilation Example

WARNING: Proper clearances from combustible materials must be maintained from all sides, top and bottom of this

appliance. Use the specications listed on this page for proper clearance to combustibles (See Table 1 and Fig. 2).

INSTALLATION OF MEDIA INTO BURNER PAN

Install lava rock/media into the burner pan. Ensure the lava

rock is a minimum of 1-inch diameter for proper operation.

Note: Do not pour Lava Rock directly from bag. It should

be placed naturally and NOT packed in tight. Loose tting is

important to ensure robust ames. Placing the lava rock in

the pan by hand, ensures no excessive dust from bag lays

in the bottom of pan and potentially plugs the injectors or

the burner pan weep holes. DO NOT BLOCK

INJECTORS WITH MEDIA.

Fire Pit

Enclousure

(2) 6”x12”

Vents

Examples of Cross Ventilation

2- Firegear 6 x12 vents

(Model # VENT-KIT-6X12)

Cross Flow Ventilation

(Min. 18 Sq. In. Per Side)

PREPARING A NON-COMBUSTIBLE STRUCTURE

The re pit can be installed on a at, stable surface, away from any combustible materials. Install re pit on any level,

outdoor non-combustible, at stable surface or a combustible oor according to the clearances specied in this manual.

NOTE: Do not place re pit directly on grass, dirt, or rocks this may prevent proper ventilation. Ensure proper water

drainage is also incorporated into the re pit enclosure.

HARD PIPING TO FIRE PIT WITHOUT GAS PROXIMITY

NOTE: Refer to the NFPA54 (National Fuel Gas Code) for proper pipe sizing. See gas line sizing chart on page 6 as a

reference.

1. Turn OFF gas supply system. NOTE: All gas connections (except for brass to brass) require the following. Clean pipe

threads using either a wire brush or steel wool. Apply pipe sealant to the ttings before making any connection.

2. Ensure all gas connections are snug, but do not over tighten! BE CAREFUL!

3. Install necessary pipe for the distance required and a manual shut-off valve at the exterior house wall. Check with

local codes for proper procedures. If pipe is to pass through a foundation or house wall, make sure to seal the area

around the pipe with weather sealant. Consult a plumber for proper installation to ensure you are providing adequate

gas supply for your application.

4. The primary gas shut-off (not supplied) will require a ½” male ared tting to enable connection of the stainless steel

ex gas with the re pit (see Fig. 12 page 11).

HIGH ELEVATION INSTALLATION

This appliance is listed for elevations from 0- 4500 feet in

Canada and the U.S. If elevation exceeds 4500 feet it may

be necessary to decrease the input rating by changing the

existing burner orice to a smaller size. Input should be

reduced 4% for each 1000 feet beyond the 4500 feet above

sea level. Check with your local gas utility for assistance

in determining the proper orice in your location. In some

cases the heating value may already be reduced and

downsizing the orice may not be necessary.

REV. A Page 7

Pro Snowake Burners and Burner Kits

REFERENCE

GAS PIPE SIZING

Length of Pipe in Feet 1/2” 3/4” 1” 1 - 1/4” 1 - 1/2” 2” 2 - 2 1/2” 3” 4”

10 275 567 1071 2205 3307 6221 10140 17990 35710

20 189 393 732 1496 2299 4331 7046 12510 25520

30 152 315 590 1212 1858 3465 5695 10110 20620

40 129 267 504 1039 1559 2992 4778 8481 17300

50 114 237 448 913 1417 2646 4343 7708 15730

60 103 217 409 834 1275 2394 3908 6936 14150

70 89 185 346 724 1086 2047 3329 5908 12050

80 78 162 307 630 976 1811 2991 5309 10830

90 69 146 275 567 866 1606 2654 4711 9613

100 63 132 252 511 787 1496 2412 4281 8736

125 54 112 209 439 665 1282 2083 3618 7382

150 48 100 185 390 590 1138 1808 3210 6549

175 43 90 168 353 534 1030 1637 2905 5927

200 40 83 155 325 491 947 1505 2671 5450

300 37 77 144 303 458 887 1404 2492 5084

NATURAL GAS : PIPE SIZING CHART

•Natural Gas (NG) flow is given in

thousands of BTU/hr. = 1cubic

foot of NG gas - 1000 BTU

•Nominal pressure at the burner

for Natural Gas is 3.5” of water

column. (Typical machine supply

5”-7”)

•Pipe length must include

additional length for all fittings.

Add approximately 5 feet of pipe

per fitting.

•Natural Gas Example: A machine

with a burner that requires

440,000 BTU would need a 1 -1/4”

pipe for a 20” long run.

LIQUID PROPANE : PIPE SIZING CHART

NOTE: The sizing charts above list the specific pipe sizes required for the amount of BTU’s for a new gas line installations. If you

are using an existing gas line you must take into consideration the existing gas line capacities to ensure you will have proper

pressure. This chart is for reference only, we recommend you consult with a Licensed Plumber/Gas Fitter or NFPA54 (National Fuel

Gas Code - current edition) for more details.

Length of Pipe in Feet 1/2” 3/4” 1” 1 - 1/4” 1 - 1/2” 2” 2 - 2 1/2” 3” 4”

10 108 230 387 793 1237 2259 3640 6434 -

20 75 160 280 569 877 1610 2613 5236 9521

30 61 129 224 471 719 1335 2165 4107 7859

40 52 110 196 401 635 1143 1867 3258 6795

50 46 98 177 364 560 1041 1680 2936 6142

60 42 89 159 336 513 957 1559 2684 5647

70 38 82 149 317 476 896 1447 2492 5250

80 36 76 140 239 443 840 1353 2315 4900

90 33 71 133 275 420 793 1288 2203 4667

100 32 68 126 266 411 775 1246 2128 4518

125 28 60 117 243 369 700 1143 1904 4065

150 25 54 105 215 327 625 1008 1689 3645

175 23 50 93 196 303 583 993 1554 3370

200 22 47 84 182 280 541 877 1437 3160

300 17 37 70 145 224 439 686 1139 2539

•Liquid Propane (LP) Gas flow is

given in thousands of BTU/hr. =

1cubic foot of LP gas - 2500 BTU.

•This chart refers to low pressure LP,

after regulation, Standard nominal

pressure at the burner for Liquid

Propane Gas is 11” of water column.

•Pipe length must include additional

length for all fittings. Add

approximately 5 feet of pipe per

fitting.

•LP Example: A machine with a

burner that requires 440,000 BTU

would need a 1” pipefor a 20’ long

run.

GAS PIPE SIZING CHART

Table 4 Gas Pipe Sizing Chart

REV. A Page 8

Pro Snowake Burners and Burner Kits

REQUIREMENTS

1. Only non-combustible materials should come in direct contact with any part of the re pit. Underneath area should

be non-combustible or a at level combustible surface according to the clearances specied in this manual.

2. Refer to the NFPA54 (National Fuel Gas Code) for proper pipe sizing. Determine the size of the re pit you are

preparing to install (Refer to page 6).

3. Determine the size of the size re pit you are preparing to install (Refer to page 4).

4. DO NOT place an LP tank inside any re pit enclosure. Locate all Propane (LP) tanks outside the enclosure.

5. You must provide a round or square opening to place the re pit into the non-combustible enclosure.

A minimum burner pan dimension is listed in Table 1.

6. Follow the local code requirements for the gas type being used. This re pit should be installed in accordance with

local codes and ordinances or in the absence of local codes, with the latest National Fuel Gas Code, ANSI Z223.1

NFPA54 or CSA B149.1, Natural and Propane Installation Code in Canada.

7. Fire pits create high temperatures, it is very important to have any combustibles at a safe distance.

8. Do not ll the enclosure cavity with gravel, rock or sand. The enclosure requires free owing air underneath to

keep it cool and provide ventilation to prevent moisture, and additional provided an outlet for gas to escape if a leak

occurs.

9. CAUTION: A minimum of 18 square inches of cross ventilation (per opposite sides) is required to keep the

enclosure dry.

10. These products are designed for outdoor use only. Not approved for any indoor use or any enclosed space.

11. This re pit is designed to have AMD Direct, Inc lava rock or glass media completely covering the burner, so that the

burner is not visible. Ensure the ends of the injectors are not blocked. Use lava rock a minimum of 1”diameter as a

base to ll the burner pan. DO NOT USE STONE OR RIVER ROCK.

12. Gas lines and ttings must be installed in to the non-combustible structure. All gas connections must be leak tested

before installation of the re pit. Soapy water leak detection is required before regular use of the re pit.

13. Do not use material that will absorb moisture over time and will not release this moisture quickly. Moisture can boil in

this material and can rapidly break apart and cause damage or personal injury.

14. Never leave any combustible material on top of the re pit. This could cause unsafe operation of this system

and damage to the component that will not be covered under our warranty.

15. Ensure proper water drainage is also incorporated into the re pit enclosure.

INSTALLATION OF FIRE PIT INTO AN APPROVED ENCLOSURE

REV. A Page 9

Pro Snowake Burners and Burner Kits

The burner pan requires a center hole a minimum of

⅞ -inch in diameter (Fig. 3). The burner also is supplied

with brass burner supports required for assembly

(Fig. 4). The number of brass supports supplied is

dependent on burner size. The 11” burner uses (4)

supports, the 18” burner uses 8 supports, the 25” burner

uses 12 supports and the 32” burner uses 16 supports.

Step 1: Install the nipple into the brass burner (Fig. 4).

Note: Use Teon tape or compound rated for gas to seal

the threads.

Step 2: Place the brass burner with nipple into the center

hole of the burner pan. Orient the burner into the proper

position.

Step 3: Temporally place the brass burner supports under

each burner leg as shown in Fig. 6, starting from the middle

of the burner at the 4-way tting and between each section

of the injectors.

Step 4: Once all the supports are placed under the burner,

carefully hold the burner into place and trace around the

base of the brass supports marking the location on the

burner pan.

Step 5: After all the locations are marked, remove the

brass burner from the pan and use one of the burner

supports to mark the center hole location of each support

traced on to the pan.

Step 6: When all support center holes are marked, drill a

1/4” hole into the burner pan at support location.

Step 7: Install all the brass supports with a 5/32” Allen

wrench (not supplied). Insert the screw through the

support and pan, then install the washer and nut. Secure

each support into place.

Step 8: Install the brass burner back into the burner pan

aligning the legs with the burner supports and install the

ared tting to enable the ex gas line to be installed.

After the gas line is secure the Snowake burner will be

held securely in place on the burner pan.

Fig. 3 Shows burner pan center hole.

BURNER ASSEMBLY

Minimum 7/8” Center Hole

Fig. 5 Shows burner with nipple installed.

Fig. 4 Brass burner supports.

Fig. 6 Locating brass burner supports.

Nipple

Brass Support Brass Support

WARNING: The brass burner supports must

be installed with the burner or you will void

the manufacturer warranty.

Fig. 7 Shows assembly of burner support to pan.

Burner Pan

Fig. 8 Shows secured to pan, installing ared tting.

REV. A Page 10

Pro Snowake Burners and Burner Kits

INSTALLING KEY VALVE

The key valve contents: 1- key valve, 1- key and 1- ange.

(See Fig. 10). The valve requires a 1¼” round clearance

hole in the non-combustible enclosure wall. See the

instructions supplied with the key valve for more specic

details. Note: Be sure to leak test all tting before

operation. Fig. 11 shows an example of a typical installation

on page 11.

OFF

Fig. 10 Key valve components.

Note: It is recommended to use the key valve assembly

provided in the Pro Brass Burner kit. Otherwise, you will

need to provide a key valve for the installation.

PRO BURNER ASSEMBLY

Injector/Jets

Hoods

Fig. 9 Proper hood orientation over injectors/jets.

CAUTION: It is imperative the “open side” of all hoods

covering the injectors/jets are installed facing downward.

Because the hoods can be removed or turned, the

orientation is extremely important to protect the injector or

jets from dust, dirt or rain. See detail in Fig. 9.

WARNING: Failure to orient the hoods in the

proper position on the burner tube will void

the manufacturer warranty.

Andere Handbücher für Pro Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMD DIrect Brenner Handbücher

AMD DIrect

AMD DIrect Pro Series Bedienungsanleitung

Beliebte Brenner Handbücher anderer Marken

Riello

Riello RS 28/M Kurzanleitung

True Induction

True Induction TI4B Bedienungsanleitung

Weishaupt

Weishaupt WG20 Series Bedienungsanleitung

Carolina Cooker

Carolina Cooker M116672 Bedienungsanleitung

Riello

Riello RX 500 S/PV Bedienungsanleitung

Unigas

Unigas HTP2000 Bedienungsanleitung

baltur

baltur BT 250 DSG 4T Bedienungsanleitung

muenkel design

muenkel design round burner Bedienungsanleitung

baltur

baltur BT 14 DSGW Bedienungsanleitung

artisan

artisan Art-SB1 Leitfaden

AESYS

AESYS TurboFire II Bedienungsanleitung

Riello

Riello RG1RKD Kurzanleitung

IKEA

IKEA GRILLSKÄR Bedienungsanleitung

RUSTA

RUSTA SAREK Bedienungsanleitung

PROPOINT

PROPOINT 8933657 Bedienungsanleitung

baltur

baltur TBL 1000 ME Referenzhandbuch

Riello Burners

Riello Burners P 200 P/G Kurzanleitung

WLD-TEC

WLD-TEC powerjet Bedienungsanleitung