American DJ Accu UFO Bedienungsanleitung

American DJ®

6122 S. Eastern Ave.

Los Angeles CA. 90040

www.americandj.com

Rev. 8/08

User Instructions

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 2

American DJ®

Accu UFO

Table of Contents

Unpacking......................................................................3

Introduction....................................................................3

Customer Support......................................................................3

Safety Precautions......................................................................4

General Information.....................................................................5

Features.........................................................................5

Registration......................................................................5

Mounting..............................................................................6

Set-Up.............................................................................7

System Menu............................................................................10

Editing Program.........................................................................23

Error Codes...............................................................................28

Operation...........................................................................30

DMX Traits.................................................................................32

Fuse Replacement....................................................................34

Cleaning..................................................................34

Trouble Shooting.......................................................................34

Warranty.................................................................35

Specifications....................................................................36

American DJ®

Unpacking: Thank you for purchasing the Accu UFO by American DJ®.

Every Accu UFO has been thoroughly tested and has been shipped in

perfect operating condition. Carefully check the shipping carton for

damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your xture for any damage and be

sure all equipment necessary to operate the unit has arrived intact. In

the event damage has been found or parts are missing, please contact

our toll free customer support number for further instructions. Please

do not return this unit to your dealer without contacting customer sup-

port rst.

Introduction: The Accu UFO is a unique, ten channel, rotating moving

head, DMX intelligent LED fixture. The fixture can operate in three dif-

ferent operating modes; stand alone, sound-active, or in a Master/Slave

configuration. The Accu UFO comes with several built in programs that

can be used, while operating as a stand alone unit or when used in

multiples linked in a master/slave configuration. For best results use

fog or special effects smoke to enhance the beams projections.

Customer Support: American DJ®provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

5:00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

Accu UFO Introduction

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 34 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Accu UFO Safety Precautions

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 4American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 3

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 5

• DMX-512 Protocol Compatible (Uses ten DMX Channels)

• 3 Operating Modes -Sound Active, Auto, and DMX Control

• Internal Microphone

• Bright 3 Watt LEDs

• Edit and Save Scenes into the Memory

• Variable Strobe (1-12 fps)

• Switchable 540˚ to 360 Pan Movement

• 265˚ Tilt Movement

• Digital Display for Address and Function Setting

Accu UFO Features

The Accu UFO carries a three year (1095 day) limited warranty. Please

fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight

pre-paid and accompany a return authorization (R.A.) number. The

R.A. number must be clearly written on the outside of the return pack-

age. A brief description of the problem as well as the R.A. number

must also be written down on a piece of paper and included in the

shipping carton. If the unit is under warranty, you must provide a copy

of your proof of purchase invoice. You may obtain a R.A. number by

contacting our customer support team on our toll free customer sup-

port number. All packages returned to the service department not dis-

playing a R.A. number on the outside of the package will be returned

to the shipper at the shippers cost.

Accu UFO Product Registration

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 6

To optimize the performance of this product, please read these operating

instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regard-

ing the use and maintenance of this unit. Please keep this manual with

the unit, for future reference.

American DJ®will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

Accu UFO General Information Accu UFO Mounting

The Accu UFO is fully operational in two different mounting positions,

hanging upside-down from a ceiling or set on a at level surface. To

avoid internal damage to the unit, never mount the unit on its side as

illustrated above. Be sure this xture is kept at least 0.5m away from

any ammable materials (decoration etc.). Always use and install

the supplied safety cable as a safety measure to prevent accidental

damage and/or injury in the event the clamp fails. Never use the car-

rying handles for secondary attachment.

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 8American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 7

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Accu UFO.™ The American DJ®Accu UFO is available in a 120v and

220v version. Because line voltage may vary from venue to venue,

you should be sure your unit voltage matches the wall outlet voltage

before attempting to operate you xture. Also be sure to only use the

included I.E.C. power cable supplied with the unit, this cable matches

the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The Accu UFO can

be controlled via DMX-512 protocol. The Accu

UFO is a ten channel DMX unit. The DMX address

is set electronically using the controls on the front

panel of the unit. Your unit and your DMX controller

require an approved DMX-512 110 Ohm Data cable

for data input and data output (Figure 1). We recom-

mend Accu-Cable DMX cables. If you are making your own cables, be

Accu UFO Set Up

Figure 1

sure to use standard 110-120 Ohm shielded cable (This cable may be

purchased at almost all pro lighting stores). Your cables should be made

with a male and female XLR connector on either end of the cable. Also

remember that DMX cable must be daisy chained and cannot be split.

Accu UFO Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 9 American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 10

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Accu UFO Set Up Accu UFO System Menu

ADDR

AXXX A001

Indicate the staring DMX address

A001 also is the setting for slave

TEST

T-01~T-XX

Automatically test the function

RUN

MSTR/ALON

Runs fixture as “master” or “alone” for auto

AUDI

MSTR/ALON

Runs fixture as “master” or “alone” for audio

PLAY

AUTO

Clos/ Hold/Auto/Audi

Runs fixture for no DMX

ALL

Reset all motors and returns fixture to home

RESE

SCAN

Reset only motors for pan/tilt

LIFE

0000~9999

Displays the total fixture running time

TIME

CLMT

Clear fixture running time

RPAN

ON/OFF

Reverses the pan movements

RTLT

ON/OFF

Reverses the tilt movements

FINE

ON/OFF

Switch between 16 bit/8 bit

MIC

M-XX

Mic sensitivity

VALU

D–XX D-00 (DXXX)

Display the DMX512 value of each channel

D ON

ON/OFF

Display turn off after 2mins

DISP

FLIP

ON/OFF

This function will reverse the display 180

RDMX

ON/OFF

Change DMX address via external controller

SPEE

SP-1/SP-2

Movement Mode Select

DFSE

ON/OFF

Resets all the fixture functions to default

FEED

ON/OFF

Pan/tilt feedback (error correction) on/off

VER

V1.0~V9.9

Software version

CODE

CXXX

Fixture code *code is “C050”

SPEC

ADJU

CH01~CH30

XXXX(-128~127)

Motor Calibration

STEP

S–01 ~S–48

Set the amount of your program

C–01~C–30

0 1 XX(00~FFH)

3 0 XX(00~FFH)

Edit the channels of each scene

TIME

T XXX(001~999)

Time for each scene

SCXX

CEDT

ON/OFF

Edit program via controller

REC.

RE.XX

Auto Save

EDIT

RUN

ON/OFF

Program test

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 11 American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 12

Accu UFO System Menu

ADDRESS MENU -

AOO1 - A511 (Value) - This is where you set the DMX address of

the unit.

TEST MENU -

T-01 - T-XX (Test) - Tests the functions of each channel. There

are nine channels. Note: Some channels cannot be tested.

PLAY MENU -

RUN - Runs the unit as a “master” or in a stand alone mode. The

unit will run a internal program mode.

AUDI (Audio) - Runs the unit as a “master” or in a stand alone,

sound active mode.

AUTO - This is a precaution mode in case the DMX signal is lost.

There are four settings to choose from:

• “Hold” - This is the default setting, which in case the signal is

lost the xute will “hold” at the last setting.

• “Close” - The xture will return to its “home” standing.

• “Auto” - The xture will go into Auto mode and run a pre-pro-

grammed show.

• “Audi” - The xture will go into Sound Active mode.

RESE (RESET) MENU -

ALL - Resets all the motors in the unit.

SCAN - Resets the motors that control pan/tilt.

TIME MENU -

LIFE - Displays the xtures total running time.

CLMT - Clears the xture running time.

RPAN (REVERSE PAN) MENU -

ON/OFF - When “On” is chosen it will reverse the pan.

DEGR MENU -

360/540 - Switch the degree of the Pan between 360 and 540.

Accu UFO System Menu

RTILT (REVERSE TILT) MENU -

ON/OFF - When “On” is chosen it will reverse the tilt.

FINE MENU -

ON/OFF - Switch between 8bit and 16bit movement.

MIC MENU -

M-01-M-70 - With this function you can make the internal mic

more or less sensitive to sound.

DISPLAY MENU -

VALU (DMX-512 Value) - Display the DMX-512 value of each

channel.

D ON - Display will turn off in 2 minutes.

FLIP - “Flips” the digital display 180º.

SPEC MENU -

RDMX - Lets you adjust the DMX address via external controller.

SPEE - Lets you select the movement mode.

DFSE (Default Settings) - Resets the unit to the default settings.

FEED - Pan/Tilt feedback (error correction) on/off.

VER (Version) - Displays the software version

ADJU - Calibration functions

EDIT MENU -

STEP (S-01 - S-48) - These are the steps slots that you write

your programs into. There are at total of 48 steps. See edit pro-

gram.

SCXX (SC01 - SC30) - These are the scenes that are stored in

your program. There are a total of 30 scenes.

REC - This will auto save your custom program.

RUN - This will run your custom program.

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 14American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 13

Accu UFO System Menu

On-Board System Menu.

The Accu UFO ccomes with an easy to

navigate system menu. This next section will detail the functions of

each command in the system menu.

To access the main menu press the MODE/ESC button on the front

of the unit. Tap the UP or DOWN butons until you reach function you

wish to change. When you reach the function you wish to change tap

the ENTER button. Again, tap the UP or DOWN buttons to change the

function. Once your changes are made, tap the ENTER button to lock

the change in the system, if the ENTER button is not selected within

eight seconds the system will automatically return to menu section. To

exit without making any changes tap the MODE/ESC button.

ADDR MAIN MENU -

ADDR DMX Address Setting via control board -

1. Access the main menu.

2. Tap the UP button until “ADDR” is displayed, press ENTER.

4. Now the display will show “A001”. Adjust the DMX address

by pressing the UP or DOWN buttons.

5. Press ENTER to conrm.

6. Press the MODE/ESC button to return to the main menu.

When the display is on “A001”, you can directly press the UP

or DN buttons to change the DMX start address.

TEST MAIN MENU -

TEST - This will test the functions of each channel.

1. Access the main menu.

2. Tap the UP button until “TEST” is displayed, press ENTER.

3. The display will show “T-01”. You can now press the up

button and test the different channels.

4. Press MODE/ESC to exit.

PLAY MAIN MENU -

RUN Run the unit in an Auto mode as a “master” in a

Master/Slave conguration, or as a stand alone unit -

1. Access the main menu.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “RUN” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice by pressing ENTER, “PASS” will ash

in the display and xture will begin its function.

AUDI Run the unit in Sound Active mode as a “master”, or

as a stand alone unit -

1. Access the main menu.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “AUDI” is displayed, press ENTER.

4. Tap the UP or DOWN button to choose between “MSTR” or

“ALON“, select your choice by pressing ENTER, “PASS” will ash

in the display and xture will begin its function.

AUTO This is a precaution mode in case you lose the DMX

signal. The xtue has 4 modes to choose from, please see

page 14 for a description of the 4 modes -

1. Access the main menu by pressing MODE/ESC button.

2. Tap the UP button until “PLAY” is displayed, press ENTER.

3. Tap the UP button until “AUTO” is displayed, press ENTER.

4. Now you can choose between “CLOSE”, “HOLD” “AUTO”, or

“AUDI”. “HOLD” is the default setting.

5. Select the mode that you want the xture to run in case of a

Accu UFO System Menu

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 16American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 15

Accu UFO System Menu

lost DMX signal and press ENTER.

RESE MAIN MENU -

ALL - When you activate the reset function, the xture will

begin the reset motion.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “ALL” is displayed.

4. Press ENTER to reset all motors, or press MODE/ESC to

cancel and return to the main menu.

SCAN - When you activate this reset function, the xture

will only reset the pan/tilt motor.

1. Access the main menu.

2. Tap the UP button until “RESE” is displayed, press ENTER.

3. Tap the UP button until “SCAN” is displayed.

4. Press ENTER to reset the pan/tilt motors, or press MODE/

ESC to cancel and return to the main menu.

TIME MAIN MENU -

LIFE - With this function you can display the total running

time of the unit.

1. Access the main menu.

2. Tap the UP button until “TIME” is displayed, press ENTER.

3. Tap the UP button until “LIFE” is displayed, press ENTER.

4. Press MODE/ESC to return to the main menu.

Accu UFO System Menu

CLMT - With this function you can clear the running time of

the xture.

1. Access the main menu.

2. Tap the UP button until “TIME” is displayed, press ENTER.

3. Tap the UP button until “CLMT” is displayed, press ENTER.

4. Press ENTER to conrm.

5. Press MODE/ESC to return to the main menu.

RPAN MENU -

RPAN - The movement of the Pan will be reversed.

1. Access the main menu.

2. Tap the UP button until “RPAN” is displayed, press ENTER.

3. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

4. Press ENTER to conrm.

5. Press MODE/ESC to return to the main menu.

RTILT MENU -

RTILT - The movement of the Tilt will be reversed.

1. Access the main menu.

2. Tap the UP button until “RTILT” is displayed, press ENTER.

3. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

4. Press ENTER to conrm.

5. Press MODE/ESC to return to the main menu.

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 18American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 17

Accu UFO System Menu

FINE MENU -

FINE - This function will switch the pan/tilt movement

between 8bit and 16bit.

1. Access the main menu.

3. Tap the UP button until “FINE” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

5. Press ENTER to conrm.

6. Press MODE/ESC to return to the main menu.

DEGR MENU -

DEGR - With this function you can switch the Pan degree

between 360° and 540°.

1. Access the main menu.

2. Tap the UP button until “DEGR” is displayed, press ENTER.

3. Press the UP or DOWN buttons to select either “630” or

“540”.

4. Press ENTER to conrm your selection.

5. Press MODE/ESC to return to the main menu.

MIC MENU -

MIC - The internal microphone can be made more or less

sensitive.

1. Access the main menu.

3. Tap the UP button until “MIC” is displayed, press ENTER.

4. The display will show “M-01”.

Accu UFO System Menu

5. Press the UP or DOWN button to adjust the microphone sen-

sitivity between “M-01 - M-99”.

6. Press ENTER to conrm when you have reached your

desired microphone sesitivity level.

7. Press MODE/ESC to return to the main menu.

DISP MAIN MENU -

VALU Display the DMX-512 value of each channel -

1. Access the main menu.

2. Tap the UP button until “DISP” is displayed, press ENTER.

3. Tap the UP button until “VALU” is displayed, press ENTER.

4. The display should show “D-00”. Press the UP button in

order to select the desired channel. If you select “D-05” the

display will only show the DMX value of the 5th channel

5. Press ENTER to conrm.

6. Press MODE/ESC to return to the main menu.

Now the display will change as per the 5th channel DMX

value.

D ON With this function “On” the display will shut off after

2 minutes -

1. Access the main menu.

2. Tap the UP button until “DISP” is displayed, press ENTER.

3. Tap the UP button until “D ON” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

5. Press ENTER to conrm.

American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 20American DJ®- www.americandj.com - Accu UFO Instruction Manual Page 19

Accu UFO System Menu

6. Press MODE/ESC to return to the main menu.

FLIP - This function will reverse the display 180º.

1. Access the main menu.

2. Tap the UP button until “DISP” is displayed.

3. Tap the UP button until “FLIP” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “ON” to acti-

vate this function, or “OFF” to deactivate this function.

5. Press ENTER to conrm.

6. Press MODE/ESC to return to the main menu.

SPEC MAIN MENU -

RDMX With this function you are able to change the DMX

address via any DMX controller. This function is factory set

to “ON” already.

1. Access the main menu by pressing MODE/ESC.

2. Tap the UP button until “SPEC” is displayed, press ENTER.

3. Tap the UP button until “RDNX” is displayed, press ENTER.

4. Press the UP button to select “ON” to activate this function,

or “OFF” to deactivate.

5. Press ENTER to conrm, and “PASS” will ash quickly.

6. Press MODE/ESC to return to the main menu.

To use this function follow the instructions:

To adjust the address of your unit you must rst go to the

address that it is currently set to. From there you can adjust the

address. First make sure all channels are set to the value of “0”.

1. On your DMX controller set the DMX value of Channel 1 to

the value “7”.

2. Now set the DMX value of Channel 2 to the value “7” to

adjust the starting address between 1 and 255. To adjust the

address between 256 and 511 set Channel 2 to the value “8” .

3. Set the DMX value of Channel 3 to your desired start-

ing address. This will take about 20 seconds before the unit

accepts the new DMX address.

EXAMPLE: So, if you want the address to be 57, you must rst

set the address that is currently assingned to the unit. The pro-

ceed to set Channel 1s’ value to “7”, Channel 2s’ value to “7”,

and Channel 3s’ value to “57”.

2ND EXAMPLE: Again, if you want the address to be 420, you

must rst set the address that is currently assingned to the unit.

If you want the set the address to 420, set Channel 1s’ value to

“7”, Channel 2s’ value to “8”, and Channel 3s to “164”. (256 +

164 = 420)

SPEE - With this function you can select the movement

mode

1. Access the main menu.

2. Tap the UP button until “SPEC” is displayed, press ENTER.

3. Tap the UP button until “SPEE” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “SP-1” or

“SP-2”.

5. Press ENTER to select your desired mode.

DFSE - With this function you can restore the factory

settings of the device. All settings will be set back to the

default values. Any edited scenes will be lost. When restor-

ing the factory settings the unit must be set to the address

that the unit was in when you started editing.

Accu UFO System Menu

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Mega Panel LED Bedienungsanleitung

American DJ

American DJ Tempest 250MSD Bedienungsanleitung

American DJ

American DJ Electra LED DMX Bedienungsanleitung

American DJ

American DJ Starball II Bedienungsanleitung

American DJ

American DJ Crystal Bedienungsanleitung

American DJ

American DJ Hyper Gem LED Bedienungsanleitung

American DJ

American DJ Flash Duo Bedienungsanleitung

American DJ

American DJ Quadra Force/Sys Bedienungsanleitung

American DJ

American DJ Emerald Star Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Montageanleitung

American DJ

American DJ Rolling Star Bedienungsanleitung

American DJ

American DJ Double Twist Bedienungsanleitung

American DJ

American DJ X-Color LED Plus Bedienungsanleitung

American DJ

American DJ Revo Burst Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ Accu Spot 250 Hybrid Bedienungsanleitung

American DJ

American DJ Octo Beam WW Bedienungsanleitung

American DJ

American DJ RollerTron Bedienungsanleitung

American DJ

American DJ Jelly Par Profile Bedienungsanleitung

American DJ

American DJ Mini-Saucer Bedienungsanleitung

American DJ

American DJ Emerald Scan Bedienungsanleitung

American DJ

American DJ Atmospheric RG LED Bedienungsanleitung

American DJ

American DJ Revo Burst Bedienungsanleitung

American DJ

American DJ Raider Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung