American DJ Mighty Scan Bedienungsanleitung

American DJ®

American DJ™

4295 Charter Street

Los Angeles Ca. 90058

www.americandj.com

Revised 4/03

User Instructions

Unpacking: Thank you for purchasing the Mighty Scan™ by Ameri-

can DJ®. Every Mighty Scan™ has been thoroughly tested and has

been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If

the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event damage has been found or parts are

missing, please contact our toll free customer support number for fur-

ther instructions. Please, do not return this unit to your dealer without

rst contacting customer support.

Introduction: The Mighty Scan™ is a DMX-512 intelligent scanner.

This fixture can operate in DMX mode, as a stand alone sound active

piece, or in a Master/Slave configuration. The Mighty Scan™ comes

with several build in programs and is best used in multiples of four.

This unit use a separate color and gobo wheel with 20 colors plus

white and 20 gobos plus spot. This piece is best used with a fog or

haze machine to enhance the beam output.

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to 5:

00 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2610

E-mail: [email protected]

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures

warranty. In the unlikely event your unit may require service please

contact American DJ® customer support.

Please do dispose of the shipping carton in the trash, please recycle

whenever possible.

Mighty Scan™ General Information

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 2

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 3

• 20 Dichroic Colors plus White

• 20 Gobos plus Spot

• High speed Shutter

• Strobes in every Color

• 16 flashes per second

• Variable Speeds

• Separate color and gobo wheels

• Split colors

• Full DMX capabilities

• Built-in programs

• Micro-Stepping Motors for Smooth Color and Gobo Transitions

• DMX-512 Protocol Compatible

• Uses 6 DMX Channels

• Full Focusing

• Fan Cooled

• Master/Slave Operation

• Sound-Active

Mighty Scan™ Features

The Mighty Scan™ carries a one year (365 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase.

All returned service items whether under warranty or not, must be

freight pre-paid and accompany a return authorization (R.A.) number.

If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. Please contact American DJ® customer support for

a R.A. number.

Mighty Scan™ Product Registration

• This unit may blow a fuse if the maximum allotted load of 6.3 amps

is reached. If the fuse needs replacement, always replace the fuse

with same exact type that was remove. Use of a different type fuse

from that which is recommended may cause fire or electric shock

and will void the manufactures warranty

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit

• Be sure that the local power outlet match that of the required volt-

age for your unit

• Do not attempt to operate this unit if the power cord has been

frayed or broken

• Do not attempt to remove or break off the ground prong from the

electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short

• Disconnect from main power before making any type of connection

• Do not remove the cover under any conditions. There are no user

serviceable parts inside

• Never operate this unit when it’s cover is removed

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall

• Do not attempt to operate this unit, if it becomes damaged

• This unit is intended for indoor use only, use of this product out

doors voids all warranties

• During long periods of non-use, disconnect the unit’s main power

• Always mount this unit in safe and stable matter

• Power cords should be routed so they are not likely to be walked

on, pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 7 for cleaning details

Mighty Scan™ Safety Precautions

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 4

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel

when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a

marked change in performance.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

Mighty SCAN™ General Instructions Mighty Scan™ Safety Precautions cont.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 5

Mighty Scan™ Controls and Functions

REAR PANEL 1. Dipswitches - These switches serve two functions. In master slave

mode these switches are used to assign a specic head address.

In DMX mode these switches are used to assign a DMX address

to the unit. In DMX mode each switch corresponds to a specic

value based on binary code. See page 10 for detailed explanation

of DMX binary code.

2. Power Cord - Connect only to a matching power outlet. Never use

this xture is the ground prong has been removed or broken off.

3. XLR Input Jack - This jack is used to accept an incoming DMX

signal or Master/Slave signal.

4. Fuse Holder - This housing stores the 6.3 amp GMA protective

fuse. Always replace with the exact same type fuse, unless other

wise instructed, by an authorized American DJ® service technician.

5. Microphone - This microphone receives external low frequencies

to trigger the unit in Sound-Active and Master/Slave mode.

6. XLR Output Jack - This jack is used to transmit the incoming

DMX signal to another DMX xture, or transmit a Master/Slave

signal to the nest Mighty Scan™ in the chain. For best results in

DMX or Master/Slave mode terminate this jack if it is the last unit

in the chain. See “Terminator” on page 12.

7. Audio Sensitivity Knob - This adjust audio sensitivity of the inter

nal microphone. Turning the sensitivity knob in the clockwise

direction will increase the sensitivity to sound. Turning the knob in

the counter clockwise direction will decrease the xture’s sensitiv-

ity to sound.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 6

Mighty Scan™ Controls and Functions

3 64

Mighty Scan™ Operation

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 8

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 7

Note: Stand-Alone and Master-Slave operation require sound to acti-

vate! The units will blackout in this mode to conserve bulb life when

there is no sound present.

Stand-Alone Operation (Sound Active): This function allows a single

unit to run to the beat of the music. Only use this function when run-

ning a single unit, or when running several units as individuals. Each

Mighty Scan in your show will act as a separate unit not relying on any

other unit for operation.

1. To activate the Sound-Active mode, set dipswitches 1, and 10

to the “ON” position. the dipswitches are located on the top of

the unit.

2. The unit will now react to the low frequencies of music via the

internal microphone.

3. Adjust the audio sensitivity knob on the top of the unit to make

the unit more or less sensitive to sound. Turning the sensitivity

knob in the clockwise direction will increase the sensitivity,

turning the knob in the counter-clockwise direction will

decrease the xture’s sensitivity to sound.

Master-Slave Operation (Sound Active): This function will allow you

to link up to 16 units together and operate without a controller. The

units will be sound activated. In Master-Slave operation one unit will

act as the controlling unit and the others will react to the controlling

units programs. Any unit can act as a Master or as a Slave.

1. Using standard XLR microphone cables, daisy chain your units

together via the XLR connectors on the rear of the units. Remem-

ber the Male XLR connector is the input and the Female XLR

is the output. The rst unit in the chain (master) will use the female

XLR connector only. For longer cable runs we suggest a termina

tor at the last fixture. Refer to the set-up procedures beginning

on page 10.

2. Follow the Master-Slave dip-switch chart on page 16 for proper

dip-switch settings.

3. After all the units settings have been set and are plugged in,

adjust the sensitivity knob on the rear of the master unit to make

them react to sound.

4. Several unit may share the same slave setting as long as there

Mighty Scan™ Installation

Linking: Your xture comes with several built-in programs. These pro-

grams are designed to work with up to 16 units when daisy-chained

together in a master-slave conguration. Any unit can function as

either a “Master Unit” or a “Slave Unit.” Link the units together using

standard DMX cable.

For a more dramatic effect, link several Color units together.

To next Mighty Scan™ if applicable

Master/Slave Linking:

1. After removing the Mighty Scan™ from the shipping container,

remove the hanging bracket knobs that have been inserted in

the styrofoam packing material. The knobs are used to hold the

fixtures’ angle. Without the knobs the weight of fixture will not

allow the unit to hold your desired operating angle.

2. This unit can be hung or placed in any safe, secure position.

3. To securely mount the fixture to truss, be sure to use a minimum

35Kg rated clamp and always try to use a safety cable when ever

possible.

4. Try not to mount the fixture too close to walls or other fixtures, this

will allow for proper cooling.

5. Connect the IEC power cord into the top of the unit.

6. Set the dipswitches according to your desired operation mode.

7. Plug the power cord into a properly grounded electrical socket.

Do not attempt to brake off or by-pass the ground prong on the

power cord, this is used for safety to reduce the risk of fire in case

of an electrical short.

8. After plugging the unit in, the lamp will ignite and the unit will reset

to the home position making a clicking noises and returning the

mirror to center home position.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 10©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 9

Mighty Scan™ Set Up

are no more than 16 units in a Master-Slave conguration, how-

ever only one unit may have the “Master - Head 1” dip switch set-

ting.

This chart details the Master/Slave dip switch setting for Master/

Slave configuration for four units. Use these dip switch setting when

you will be using two or more fixtures in a Master/Slave configuration.

The “Master - Head 1” settings should only be used once.

Universal DMX Control: This function allows you to use a univer-

sal DMX 512 controller such as the American DJ® DMX Operator™

or Show Designer™ to control lamp intensity, color, and gobo.

Operating through a DMX controller allows the freedom to create

unique programs tailored to one’s individual needs.

1. The Mighty Scan™ uses three DMX channels. Channel one con-

trols the lamp intensity (dimmer), channel two controls the color

selection, and channel three control the gobo wheel. Please refer

to page 16 for a detailed description of the DMX traits.

2. To control your fixture in DMX mode, follow the unit set-up proce-

dures beginning on page 10 as well as the set-up specifications

that are included with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture

traits.

4. This will allow you to create custom programs.

5. When using a DMX controller and setting up for DMX operation.

6. For help operating in DMX operation consult the manual included

with your DMX controller.

7. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture in you DMX chain.

Mighty Scan™ Operation

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

Mighty Scan.™ Because line voltage may vary from venue to venue,

you should be sure your unit voltage matches the wall outlet voltage

before attempting to operate you xture.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used as a form of communication between intelligent fixtures

and controllers. A DMX controller sends DMX data instructions from

the controller to the xture. DMX data is sent as serial data that trav-

els from xture to xture via the DATA “IN” and DATA “OUT” XLR ter-

minals located on all DMX xtures (most controllers only have a DATA

“OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of

different manufactures to be linked together and operate from a sin-

gle controller, as long as all xtures and the controller are DMX com-

pliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order

in which fixtures are connected in a DMX line does not influence the

DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address

of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Dip-switches in DMX mode: This unit uses dip switches to assign

a DMX address. Each dip switch represents a binary value.

Dip Switch 1 address equals 2

Dip Switch 2 address equals 3

Dip Switch 3 address equals 5

Dip Switch 4 address equals 9

Dip Switch 5 address equals 17

Dip Switch 6 address equals 33

Dip Switch 7 address equals 65

Dip Switch 8 address equals 129

Dip Switch 9 address equals 257

ON 1 98765432 10

1293 9 33

257651752

DMX CHANNEL

1 98765432 10

All Slaves

1 98765432 10

Master - Head 1

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 12

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 11

Data Cable Requirements (For DMX and Master/Slave Opera-

tion): The Mighty Scan™ can be controlled via DMX-512 protocol.

The DMX address is set using the dip-switches on the rear panel of the

Mighty Scan™. Your unit excepts 3-pin XLR connector for data input

and data output (Figure 5). When using a DMX controller with 5-Pin

XLR output jacks or when linking from a DMX x-

ture with 5-Pin XLR jack to the Mighty Scan™, be

sure to follow the pin conversion chart on page

12. If you are making your own cables, be sure to

use standard two conductor shielded cable (This

cable may be purchased at almost all pro sound

and lighting stores). Your cables should be made

with a male and female XLR connector on either

end of the cable. Also remember that DMX cable

must be daisy chained and can not be split.

Figure 5

Mighty Scan™ Set Up

Figure 6

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Mighty Scan™ Set Up

Notice: Be sure to follow gures 6 and 7 when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 7

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number ZDMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 8

Since the unit automatically has a DMX address of 1, dip switch 2 has

a value of 3, and dip switch 5 has a value of 17, the combination cre-

ates a DMX value of 21.

Set DMX address 21: Set DMX address 201:

Unit has address of 1 Unit has address of 1

Dip-switches # 2 = 3 Dip-switches # 1 = 2

5 = 17 2 = 3

= 21 7 = 65

8 = 129

= 201

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan-

dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be

used, these adaptors are readily available at most electric stores. The

chart below details a proper cable conversion.

Important Notice: This fixture follows the European DMX

addressing standard. When operating this fixture with a standard

DMX-512 controller, the fixture’s DMX value automatically starts on

one (1) with all the dip switches in the off position. For example: To

get a DMX value of one (1) you would have to flip dip switch one (1)

to the on position. In the case of the Mighty Scan™ however, dip

switch one (1) on, would give the Mighty Scan™ a DMX value of two

(2). To get a value of one (1), all the dip switches would have to be in

the off position. To get a DMX value of two (2) set the DMX value to

one (1), for three (3) set the DMX value for two.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 13

Halogen Lamp Warning:

This fixture is fitted with a halogen lamp which is

highly susceptible to damage if improperly han-

dled. Never touch the lamp with your bare fingers

as the oil from your hands will shorten lamp life.

Also, never move the fixture until the lamp has

had ample time to cool. Remember, lamps are not

covered under warranty conditions.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

Mighty Scan™ Lens Focusing

Mighty Scan™ Halogen Lamp Warning

1. Hang the fixture in your final desired position.

2. If no controller is being used,

A. Set dip switch ten (10) to the on position.

B. Turn the sensitivity to minimum position.

C. Plug the fixture in. The unit’s shutter will open and the

mirror will reset to the center.

3. If a controller is being used,

A. Plug the fixture in.

B. Use your controller to set the fixture’s mirror in a center

home position.

C. Open the shutter and select a gobo.

4. Adjust lens by turning it in a clockwise and counter-clockwise

direction until the projected pattern is in a sharp focus.

Mighty Scan™ Lens Focusing

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 14

Unit Top Cover

Mighty Scan™ Fuse & Lamp Replacement

Caution: Always replace with the exact same type lamp and fuse,

unless otherwise specified by an authorized American DJ® techni-

cian. Replacing with anything other than the specified part can dam-

age the unit and will void the manufactures warranty.

Warning: If, after replacing the lamp or fuse either one continues

to blow, STOP using the unit. Contact customer support for further

instructions, you may have to return the unit for servicing. Continuing

to use the unit may cause serious damage.

Fuse Replacement: Disconnect the unit’s main power supply.

Insert a standard flat head screw driver in to the fuse holder housing.

Remove the fuse holder to expose the fuse. Remove the old fuse and

discard it. Replace the fuse with the same type. Insert the fuse holder

back into it’s housing and turn it in clockwise direction to lock the

holder in place.

Lamp Replacement: Caution! Never attempt to change the lamp

while the fixture is plugged in. Always disconnect the main power

and allow the unit ample time to cool before attempting to replace the

lamp. Lamp replacement has been made simple by incorporating the

use of a flip-up top cover that is retained by a single thumb screw.

1. Be sure to follow the proper handling procedures that deal

with halogen lamps. Never touch the new lamp with your bare

fingers.

2. Remove the single thumb screw located on top of the unit. This

screw holds the flip-up lamp socket assembly cover in place.

3. Flip-up the cover. The cover is on hinges and will not fall off.

4. Carefully remove the old lamp and discard it in the trash.

5. Replace the lamp with an exact match and reassemble.

Flip-Up Lamp Cover

Thumb Screw Retaining Hole

Lamp/Socket Assembly

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 16

Mighty Scan™ Cleaning

Mighty Scan™ Trouble Shooting

Fixture Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal optical lenses and mirror should be carried out periodically to

optimize light output. Cleaning frequency depends on the environ-

ment in which the fixture operates (I.e. smoke, fog residue, dust,

dew). In heavy club use we recommend cleaning on a monthly basis.

Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external lens with glass cleaner and a soft cloth every

20 days.

4. Clean the internal lens with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

Trouble Shooting:

Listed below are a few common problems that you may encounter,

with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a standard 120V wall

outlet.

2. Be sure the fuse has not blown. The fuse is located on the

rear panel of the unit.

3. Remove the lamp cover and be sure the lamp is seated in its

socket properly. Occasionally lamps become loose during ship

ping be sure the lamp is push in to its socket all the way.

4. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

2. Be sure the SENSITIVITY KNOB (3) is not set to the maximum

position.

3. Be sure the dip-switches are set for Stand-Alone mode.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 15

ON ON

Mighty Scan™ 1

Mighty Scan™ DMX-512 Settings

1 98765432 10 1 98765432 10

1 98765432 10

Mighty Scan™ 15Mighty Scan™ 14Mighty Scan™ 13

Mighty Scan™ 12Mighty Scan™ 11Mighty Scan™ 10

Mighty Scan™ 8 Mighty Scan™ 9

Mighty Scan™ 6

Mighty Scan™ 5

Mighty Scan™ 4

Mighty Scan™ 3Mighty Scan™ 2

Mighty Scan™ 7

Mighty Scan™ 16

Channel Value Function

1 0 - 255 PAN

2 0 - 255 TILT

3 0 - 255 PAN/TILT SPEED SLOW FAST

4 0 - 155 COLOR

0 - 3 BLUE 107

8 - 11 BLUE 107

16 - 19 BLUE 110

24 - 27 BLUE 101

32 - 35 CYAN 401

40 - 43 GREEN 201

48 - 51 GREEN 204

56 - 59 YELLOW 601

64 - 67 ORANGE 306

72 - 75 RED 304

80 - 83 PINK 303

88 - 91 MAGENTA 501

96 - 99 MAGENTA 507

104 - 107 CYAN 104

112 - 115 ORANGE 302

120 - 123 TURQUOISE 208

128 - 131 PINK 310

136 - 139 YELLOW 603

144 - 147 UV BLUE 108

152 - 155 RED 301

160 - 175 OPEN (NO FILTER)

176 - 208 ROTATION (FAST SLOW)

209 - 221 ROTATION STOP

222 - 255 ROTATION (SLOW FAST)

Mighty Scan™ DMX Values and Functions

Note: The Mighty Scan™ has split color capabilities. The chart only

shows the values for solid color options. To get a split color set the

DMX value to somewhere in between the two colors you want to

split. Only a pair of colors that are next to each other on the color

wheel can be split. For example Blue 107 and Blue 110 are a pair of

colors that are next to each other. Setting the DMX value to 13 will

give a split color of the two.

Mighty Scan™ DMX Values and Functions cont.

Channel Value Function

5 0 - 175 GOBO

0 - 7 LARGE SPOT

7 - 15 TUNNEL

16 - 23 TRI-TUNNEL

24 - 31 SUNFLOWER

32 - 39 DUAL DOTTED LINE

40 - 47 SINGLE DOTTED LINE

48 - 55 TRIANGLE

56 - 63 SWIRL

64 - 71 MULTI-STAR

72 - 79 SEGMENT TUNNEL

80 - 87 STAR

88 - 95 SMALL SPOT

96 - 103 SEGMENT SQUARES

104 - 111 TWISTER

112 - 119 SPLIT FOUR

120 - 127 BARS

128 - 135 SPLASH

136 - 143 ASTERISK

144 - 151 MULTI-SMALL DOT

152 - 159 EURO STARS

160 - 175 BUBBLES

254 SOUND ACTIVE SLOW

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 17 ©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 18

Mighty Scan™ GOBOS

Mighty Scan™ DMX Values and Functions cont.

Channel Value Function

6 0 - 175 SHUTTER/STROBE

0 - 8 BLACKOUT

8 - 15 SHUTTER OPEN (LAMP ON)

16 - 23 SHUTTER CLOSED

24 - 127 STROBE (FAST SLOW)

128 - 255 STROBE (SLOW FAST)

Mighty Scan™ DMX Dip Switch Chart

This chart list the DMX dip switch setting for DMX address 1 through

511. Follow the instructions below to configure fixture dip switches

with your desired DMX address.

©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 19 ©American DJ Supply® - www.americandj.com - Mighty Scan™ Instruction Manual Page 20

 

 









    

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

               

            

       

      

        

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

    

Di p Swit ch Pos iti o n



             

    



Dipswitches

D M X A d d r e s s

The center numbers of this chart (1-511) represent a DMX address. The

"X"'s and "O"'s along the top and side of the chart represent dip switch

poistion ("X" for off and "O" for on). Find your desired DMX address from

the center chart. Identify the position for dip switches 1-5 from the chart on

the left and dip switches 6-9 from the chart on the top. Adjust the dip

switches on your fixture to match the position settings of the chart. For

fixtures with 10 dip switches; dip switch 10 is reserved for special functions.

Andere Handbücher für Mighty Scan

Inhaltsverzeichnis

Andere American DJ DJ-Equipment Handbücher

American DJ

American DJ Trance Wheel Bedienungsanleitung

American DJ

American DJ Electra LED DMX Bedienungsanleitung

American DJ

American DJ 46HP LED Bedienungsanleitung

American DJ

American DJ H2O 250 EX Bedienungsanleitung

American DJ

American DJ Concept Color Bedienungsanleitung

American DJ

American DJ Revo Sweep Bedienungsanleitung

American DJ

American DJ DJ Scan 250 Bedienungsanleitung

American DJ

American DJ SCENE SETTER Bedienungsanleitung

American DJ

American DJ Micro Moon Bedienungsanleitung

American DJ

American DJ Mini Tri Ball Bedienungsanleitung

American DJ

American DJ FLASHBACK 4 Bedienungsanleitung

American DJ

American DJ Flight-Moon Bedienungsanleitung

American DJ

American DJ X-Color LED Plus Bedienungsanleitung

American DJ

American DJ Aquarius Bedienungsanleitung

American DJ

American DJ Light Station Bedienungsanleitung

American DJ

American DJ Mega Panel LED Bedienungsanleitung

American DJ

American DJ Hyper Gem LED Bedienungsanleitung

American DJ

American DJ Gobo Motion LED Bedienungsanleitung

American DJ

American DJ Roto-Balls VS MKII Bedienungsanleitung

American DJ

American DJ TRI GEM LED Bedienungsanleitung

American DJ

American DJ Mini Mace Bedienungsanleitung

American DJ

American DJ Royal Sky Bedienungsanleitung

American DJ

American DJ BPP-20 Bedienungsanleitung

American DJ

American DJ UVLED Bar16 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung