American DJ X-Move LED Plus R Bedienungsanleitung

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 2

X-Move LED Plus R General Information

Unpacking: Thank you for purchasing the X-Move LED Plus R by

American DJ®. Every X-Move LED Plus R has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The X-Move LED Plus R is a nine channel DMX intel-

ligent, moving head, mini LED fixture. The X-Move LED Plus R can

operate as a stand alone fixture or in a Master/Slave configuration.

The X-Move LED Plus R has three operating modes; a sound active,

show mode, DMX controlled. For best results use fog or special effects

smoke to enhance the beams projections.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

User Instructions

Rev. 2/11

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 18 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

X-Move LED Plus R Safety Precautions

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 4American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 3

• DMX-512 Protocol Compatible (Nine DMX Channels)

• RGB + White

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 4 Preprogrammed Shows

X-Move LED Plus R Features

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

American DJ®.

During operation the housing may become extremely hot. Avoid

touching the unit with bare hands while in use.

American DJ® will not accept any liability for any resulting damages

caused by the non-observance of this manual or any unauthorized

modication to this unit.

X-Move LED Plus R Handling Precautions

X-Move LED Plus R Warranty Registration

The X-Move LED Plus R carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase

and warranty. You may also register your product online at www.

americandj.com. All returned service items whether under warranty or

not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy

of your proof of purchase invoice. Please contact American DJ® cus-

tomer support for a R.A. number.

To optimize the performance of this product, please read these

operating instructions carefully to familiarize yourself with the basic

operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please

keep this manual with the unit, for future reference.

X-Move LED Plus R General Instructions

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 6American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 5

Power Supply: Before plugging your unit in, be sure the source volt-

age in your area matches the required voltage for your American DJ®

X-Move LED Plus R.The American DJ® X-Move LED Plus R is available

in a 120v and 220v version. Because line voltage may vary from venue

to venue, you should be sure your unit voltage matches the wall outlet

voltage before attempting to operate you xture. Also be sure to only

use the included I.E.C. power cable supplied with the unit, this cable

matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix-

ture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX

fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of different manufactures to be linked together and operate from a

single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using

several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence

the DMX addressing. For example; a fixture assigned a DMX address

of 1 may be placed anywhere in a DMX line, at the beginning, at the

end, or anywhere in the middle. Therefore, the first fixture controlled

by the controller could be the last fixture in the chain. When a fixture

is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located

in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The X-Move LED

Plus R can be controlled via DMX-512 protocol.

The X-Move LED Plus R is a nine channel DMX

unit. The DMX address is set electronically using

the controls on the front panel of the unit. Your

unit and your DMX controller require a approved

DMX-512 110 Ohm Data cable for data input and

data output (Figure 1). We recommend Accu-Cable DMX cables. If you

X-Move LED Plus R Set Up

Figure 1

are making your own cables, be sure to use standard 110-120 Ohm

shielded cable (This cable may be purchased at almost all professional

sound and lighting stores). Your cables should be made with a male

and female XLR connector on either end of the cable. Also remember

that DMX cable must be daisy chained and cannot be split.

X-Move LED Plus R Set Up

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-

nected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last

unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 7 American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 8

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX

xtures may be implemented in a 3-pin DMX line. When inserting stan-

dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,

these adaptors are readily available at most electric stores. The chart

below details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

X-Move LED Plus R Set Up X-Move LED Plus R System Menu

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 10American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 9

X-Move LED Plus R System Menu

System Menu: When making adjustments you can press

ENTER to conrm your setup or you can wait 8 seconds for

automatic setup. To exit without making any adjustments

press the MENU button.

ADDR - DMX Address Setting.

1. Tap the either the MENU, UP, or DOWN buttons until “ADDR”

is displayed, press ENTER.

2. The current address will now be displayed and ashing.

Press the UP or DOWN buttons to nd your desired address.

Press ENTER to set your desired DMX address.

SHND - This will let you choose one of the four prepro-

grammed shows. See show descriptions below.

1. Tap the either the MENU button until “SHND” is displayed,

press ENTER. Either “SH 1”, “SH 2”, “SH 3” or “SH 4” will be dis-

played.

2. Tap the UP or DOWN buttons to nd you desired show and

then press ENTER to conm and exit.

SHOWS:

Show 1 - For xtures placed on the oor, the tilt movement

angle is 210°

Show 2 - For fixtures fixed to the ceiling or truss, the tilt move-

ment angle is 90°.

Show 3 - For fixtures placed on a table or stage. The beam is

projected at the audience’s direction; i.e. in front of the stage.

Pan movement angle (left to right to left) is 160°. Tilt movement

angle is 90°.

Show 4 - For fixtures fixed to the ceiling or truss. The beam is

projected at the audience’s direction; i.e. in front of the stage.

Pan movement angle (left to right to left) is 160°. Tilt movement

angle is 90°.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Tap the MENU button until “SLND” is displayed, press

ENTER. Either “SL 1” or “SL 2” will be displayed.

2. Tap the UP or DOWN buttons until your desired setting is

displayed, press ENTER to conm.

NOTE: In a Master/Slave conguration you can set one xture

to Master and then set the next xture to “SL 2”, the xtures will

now have contrast movement to each other.

SOUN - Sound Active mode.

1. Tap the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

“OFF” to deactivate sound active mode.

3. Press ENTER to conrm.

BLND - Blackout or Stand by mode.

1. Tap the MENU button until “BLND” is displayed, press

ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes”

is displayed, press ENTER to conm. The xture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and

press Enter.

I PAN - Pan Inversion

1. Tap the MENU button until “I PAN” is displayed, press ENTER.

Either NO or 1 will be displayed.

X-Move LED Plus R System Menu

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 11 American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 12

MENU to exit.

TEST - This function will run a self test program. The test

program will test pan/tilt movement and colors.

1. Tap the MENU button until “TEST” is displayed, press ENTER.

2. The xture will now run a self test.

TEMP - With this function you can check the temperature

of the xture.

1. Tap the MENU button until “TEMP” is displayed, press ENTER.

2. The temperature of the xture will now be displayed. Press

MENU to exit.

FHRS - With this function you can display the running time

of the unit.

1. Tap the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the xture will now be displayed. Press

MENU to exit.

VER - With this function you can display the version soft-

ware of the unit.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The software version will now be displayed. Press MENU to

exit

RSET - Use this function to reset the unit.

1. Tap the MENU button until “RSET” is displayed, press ENTER.

2. The xture will now reset,

OTIL - With this function you can adjust and set the x-

X-Move LED Plus R System Menu

2. To activate the Pan inversion tap the UP or DOWN buttons

until I is displayed, press ENTER to conm. To deactivate Pan

inversion, select No and press Enter.

I TLT - Tilt Inversion

1. Tap the MENU button until “I TLT” is displayed, press ENTER.

Either NO or 1 will be displayed.

2. To activate the Tilt inversion tap the UP or DOWN buttons

until I is displayed, press ENTER to conm. To deactivate Tilt

inversion, select No and press Enter.

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Tap the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at

all times, or “OFF” to switch to have the LED display switch off

after 10 seconds.

3. Press ENTER to conrm.

DISP - This function will reverse the display 180º.

1. Tap the MENU button until “DISP” is displayed, press ENTER.

2. Press ENTER to “ip” the display. Press ENTER to “ip” it

again. Press ENTER when you have made your desired setup.

FADJ - This function will allow you to focus the lens for a

clear LED output.

1. Tap the MENU button until “FADJ” is displayed, press

ENTER. The xture will turn a different way each time the

ENTER button is pressed.

2. With the spot pointed at a at wall or surface, at the distance

it will be set up, you can turn the lens to adjust the clarity. Press

X-Move LED Plus R System Menu

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 13 American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 14

Operating Modes: The X-Move LED Plus R can operate in

three different modes. In each mode you can run the fixture as

a stand alone fixute or in a master/slave confiugration. This next

section will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

• Show mode -

The fixture will run one of four shows that you choose.

• DMX control mode -

This function will allow you to control each individual fixtures traits

with a standard DMX-512 controller such as the Elation® Show

Designer.™

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound

activated. In Master-Slave operation one unit will act as the controlling

unit and the others will react to the controlling units programs. Any unit

can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressiing the ENTER button.

3. On the slave units tap the MENU button until “SLND” is dis-

played, and Press ENTER. Choose either “SL 1” or “SL 2” and

press ENTER. See page 10 for more info.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,

dimmer and strobe. A DMX controller allows you to create unique

programs tailored to your individual needs.

1. The X-Move LED Plus R is a nine DMX channel DMX fixture. See

pages 16-17 for detailed description of the DMX values and

X-Move LED Plus R Operation

tures home position.

1. Press the ENTER button for at least 5 seconds to enter into

offset mode.

2. Press the UP or DOWN buttons until “OTIL” is displayed, and

press ENTER. The display will begin to ash.

3. Press the UP or DOWN buttons to adjust to your desired

home position. Once you have found your desired position

press the ENTER button to set and save, or press the MENU

button to return to return to offset functions without any

changes. If you do not press any buttons for 8 seconds the

xture will return to the offset functions automatically.

X-Move LED Plus R System Menu

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 16American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 15

X-Move LED Plus R Operation

traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-7 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER. Tap the UP or DOWN buttons so that “ON” is dis

played and press ENTER.

2. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: This mode allows either a single unit or several units

linked together, to run one of four shows that you choose.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you nd your desired show,

and press ENTER.

X-Move LED Plus R UC3 Control

Stand By

Blackout the unit

Function

1. Sync. Strobe

2. Async strobe

3. Sound Strobe

Show

1-4

1. Select Color

2. Select Gobo

Mode

Sound (LED OFF)

Show (LED

Slow Blinking)

LED ON

The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

X-Move LED Plus R DMX Traits

Channel Value Function

1 0 - 255 PAN

2 0 - 255 TILT

3 COLORS

0 - 14 WHITE

15 - 29 RED

30 - 44 BLUE

45 - 59 GREEN

60 - 74 YELLOW

75 - 89 PINK

90 - 104 LIGHT BLUE

105 - 119 LIGHT GREEN

120 - 127 LIGHT YELLOW

128 - 254 RAINBOW EFFECT SLOW - FAST

255 SOUND ACTIVE

4 GOBO WHEEL

0 - 9 OPEN

10 - 18 GOBO 1

19 - 27 GOBO 2

28 - 36 GOBO 3

37 - 46 GOBO 4

47 - 55 GOBO 5

56 - 63 GOBO 6

64 - 73 OPEN SHAKE

74 - 82 GOBO 1 SHAKE

83 - 91 GOBO 2 SHAKE

92 - 100 GOBO 3 SHAKE

101 - 110 GOBO 4 SHAKE

111 - 119 GOBO 5 SHAKE

120 - 127 GOBO 6 SHAKE

128 - 254 GOBO WHEEL ROTATION SLOW - FAST

255 SOUND ACTIVE

5 GOBO ROTATION

0 - 9 STOP

10 - 120 CLOCKWISE FAST - SLOW

121 - 134 STOP

135 - 247 COUNTER-CLOCKWISE SLOW - FAST

248 - 255 STOP

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 17

X-Move LED Plus R DMX Traits

Channel Value Function

6 SHUTTER/STROBE

0 - 7 BLACKOUT

8 - 15 SHUTTER OPEN

16 - 131 STROBING SLOW - FAST

132 - 139 SHUTTER OPEN

140 - 180 SHUTTER SLOW OPEN - FAST CLOSE

181 - 190 SHUTTER OPEN

191 - 231 SHUTTER FAST OPEN - SLOW CLOSE

232 - 239 SHUTTER OPEN

240 - 247 RANDOM STROBE

248 - 255 SHUTTER OPEN

7 0 - 255 DIMMER 0% - 100%

8 MOVING HEAD MOVEMENT

0 - 7 NO FUNCTION

8 - 28 MOVEMENT 1

29 - 49 MOVEMENT 2

50 - 70 MOVEMENT 3

71 - 91 MOVEMENT 4

92 - 112 MOVEMENT 5

113 - 133 MOVEMENT 6

134 - 154 MOVEMENT 7

155 - 175 MOVEMENT 8

176 - 196 MOVEMENT 9

197 - 217 MOVEMENT 10

218 - 238 MOVEMENT 11

239 - 255 MOVEMENT 12

9 0 - 255 MOVEMENT SPEED FAST - SLOW

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 18

X-Move LED Plus R Gobo Replacement

This unit comes with interchangable gobos. When changing

the gobos please be very careful. Follow the instructions below,

and see the gure pictures on the next page.

Caution! Never open the unit when in use. Always disconnect

the main power before attempting to change the gobos.

1. To change the gobo, you must remove the top half of the

moving head. The top half of the moving head does not

have the lens attached to it. The lens is on the top half of the

head (Figure 1).

2. Unscrew the 3 phillips screws that secure the top half of the

head. Remove the top half of the head.

3. When you remove the shell you will be able to access the

gobo wheel. Rotate the head so that the lens is aimed up

(Figure 2). Turn the gobo wheel with your hand until you

find the gobo you would like to change, then turn the color

wheel until the empty space (spot) is below your desired

gobo.

4. Using a pair of needle nose pliers, grab the fixture ring that

holds the gobo in place and remove the ring (Figure 3).

5. Once the ring is removed, carefully use your finger to push

the gobo up and out (Figure 3). You can then tilt the head so

that the gobo falls into your hand (Figure 4).

6. Carefully insert your new gobo and insert the fixture-ring.

7. Reassemble the unit.

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 19

X-Move LED Plus R Cleaning

X-Move LED Plus R Trouble Shooting

Trouble Shooting: Listed below are a few common problems that

you may encounter, with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a standard 120v wall

outlet.

2. Be sure the external fuse has not blown. The fuse is located on

the rear panel of the unit.

3. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

internal and external optical lenses and mirror should be carried out

periodically to optimize light output. Cleaning frequency depends on

the environment in which the fixture operates (I.e. smoke, fog residue,

dust, dew). In heavy club use we recommend cleaning on a monthly

basis. Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

X-Move LED Plus R Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been

removed located the fuse holder located inside the power socket.

Insert a flat-head screw driver into the power socket and gently pry

out the fuse holder. Remove the bad fuse and replace with a new one.

The fuse holder has a built-in socket for a spare fuse be sure not to

confuse the spare fuse with active fuse.

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 20

X-Move LED Plus R Gobo Replacement

Figure 1

Figure 2

Figure 3

Figure 4

Inhaltsverzeichnis

Andere American DJ Leuchte Handbücher

American DJ

American DJ Mini Starball II Bedienungsanleitung

American DJ

American DJ Profile Panel RGB Bedienungsanleitung

American DJ

American DJ Flash Duo VS Bedienungsanleitung

American DJ

American DJ Revo II Bedienungsanleitung

American DJ

American DJ Illusion Dotz 4.4 Bedienungsanleitung

American DJ

American DJ Flat Par QWH12X Bedienungsanleitung

American DJ

American DJ ActivePod Bedienungsanleitung

American DJ

American DJ Mega Pixel Arch Bedienungsanleitung

American DJ

American DJ Accu Scan 250 Bedienungsanleitung

American DJ

American DJ X-Move LED 25R Bedienungsanleitung

American DJ

American DJ Accu UFO PRO Bedienungsanleitung

American DJ

American DJ Fantasy Scan 250 Bedienungsanleitung

American DJ

American DJ Fusion Scan 250 Bedienungsanleitung

American DJ

American DJ Double Roller Bedienungsanleitung

American DJ

American DJ Color Expander Bedienungsanleitung

American DJ

American DJ Globe Color Bedienungsanleitung

American DJ

American DJ Vizi Wash LED 108 Bedienungsanleitung

American DJ

American DJ Fantasy 250 Bedienungsanleitung

American DJ

American DJ ColorPod Bedienungsanleitung

American DJ

American DJ ScanTron Bedienungsanleitung

American DJ

American DJ Event Bar Q4 Bedienungsanleitung

American DJ

American DJ VORTEX/G Bedienungsanleitung

American DJ

American DJ Vizi Spot LED PRO Bedienungsanleitung

American DJ

American DJ Jelly GO Par64 Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung