American DJ DJ SCAN Bedienungsanleitung

USER

INSTRUCTIONS

Caution: Read all instructions before attempting to install or power unit up!

Specifications: DJ Scan

Weight: 21 lbs.

Dimensions: 18x 8.6 x 4.3

Lamp: JCR/H5 15v-150w

Fuse: 5A/250v GMA

Voltage: 115v/230v, 60Hz/50Hz

Gobos: 10 Plus Spot

Colors: 7 Plus White

Cooling: Fan Cooled

Working Position: Any Safe Position

HALOGEN LAMP WARNING!

This fixture is fitted with a halogen lamp which

is highly susceptible to damage if improperly

handled. Never touch lamp with your bare fin-

gers as the oil from your hands may shorten

the lamp life. Also, never move the fixture until

the lamp has had ample time to cool.

Remember, lamps are not covered under war-

ranty conditions.

©American DJ Supply ®. Los Angeles, CA. 90058 USA DJ Scan Page 1

Congratulations and thank you for purchasing the American DJ “DJ Scan,” one of the finest pieces of its

kind on the market today! The DJ Scan is a great inexpensive, light weight, mini intelligent fixture. Due to

it’s physical specifications, it’s a great piece for mobile DJ’s, roller rinks, small clubs, bars, and bowling cen-

ters. When used in multiples of two (2) or more, these units create an effect that rivals that of units that can

cost up to three times the price. The DJ Scan™ was designed to run in master/slave mode but can be used

with a standard dmx controller.

The DJ Scan features a bright 150 watt/500 Hr lamp life halogen bulb with a separate gobo and color

wheel. The color wheel features seven brilliant colors plus white and the gobo wheel features 9 gobos plus

a large and small spot. This units is ready to be installed or hung and powered right out of the box. There

is no assembly required. This fixture incorporates the use of high quality stepper motors for a more accu-

rate mirror movement. Mirror movement allows for a full 90 degree tilt (vertical) and a full 90 degree

pan (horizontal). An internal built in microphone allows the fixtures to run in Stand Alone mode so there

is no need for an external controller. The DJ Scan™ may also be set-up to run in a Master-Slave mode

when used in multiples, up to 16 units. When used in the Master-Slave mode, the unit will chase to sever-

DJ Scan™ Features

American DJ®

DJ Scan™ Introduction

internal programs. The DJ Scan™ can also be controlled via a standard DMX controller such as the

American DJ Show Designer,™or the American DJ®DMX Operator,™giving the user independent control

over the gobo and color wheel as well as the mirrors pan and tilt movements.

Note: The built in programs in the DJ Scan are so good you may never need a DMX controller.

American DJ provides a toll free customer support line, to provide set up help and to answer any ques-

tion should you encounter problems during your set up or initial operation. You may also visit us on

the web at www.americandj.com for any comments or suggestions.

Service Hours Monday through Friday are 10:00 a.m. to 5:00 p.m. Pacific Time.

Voice (800) 322-6337

Fax (323) 582-2610

E-mail: [email protected]

Power Supply:

Before plugging your unit in be sure the voltage in your area matches the required voltage for your

unit. The DMX Operator™ require a DC 9v 200mA power supply.

The DMX Operator™ is available in a 115v and 230v version. Because line voltage may vary from

venue to venue, you should be sure to plug your power supply into a matching wall outlet before

attempting to operate you controller.

Data Cable (DMX Cable) Requirements:

Your fixture and your controller require a standard 3-pin XLR connector for data input and data output

(Figure 1). If you are making your own cables be sure to use standard two conductor shielded cable

(This cable may be purchased at almost all pro sound and lighting stores). Your cables should be

made with a male and female XLR connector on either end of the cable. Also remember that DMX

cable must be daisy chained and can not be “Y”ed or split.

Notice: Do not use the ground lug on the XLR connector. Do not connect the shield conductor

to the ground lug or allow the shield conductor to come in contact with XLR outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

DJ Scan™ Features cont.

DJ Scan™ Customer Support

DJ Scan™ Set Up

Figure 1

American DJ Supply®. Los Angeles, CA. 90058 USA DJ Scan Page 2

Special Note: For excessive cable runs of 100ft. total or more, we recommend using a termi-

nator of 80-100 ohms/.5w. Long cable runs can sometimes cause erratic behavior. Using a cable ter-

minator will decrease the possibilities of erratic behavior.

For best results use fog or special effects smoke to enhance the beams projections. The DJ

Scan™comes with a protective transportation cover. Be sure to remove it before attempt-

ing any operation!

Stand-Alone Operation (Sound Active):

1. To operate as a stand alone unit, via its internal chases and microphone, turn all dip switches off

(see Diagram1).

2. Adjust the sensitivity knob on the bottom of the unit so the unit will react to sound.

3. The DJ Scan™ will now react to the bass sound of music via the internal microphone.

Master-Slave Operation (Sound Active):

1. This function will allow you to link up to 16 units to run on the master units internal programs.

2. In Master-Slave operation one unit will act as the controlling unit and the others will react to the

controlling units programs. Any unit can act as a Master or as a Slave.

3. Daisy chain your units via the XLR connector on the bottom of the units.

4. Use standard XLR microphone cables to link your units together. Remember that the Male XLR

connector is the input and the Female XLR connector is the output.

5. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain

will use the male XLR connector only.

6. Turn all the master units dip switches to the off position (see Page 6/Diagram1).

7. Please follow chart on page 4 for all slave dipswitch settings. Note only one fixture may use the

master units dip switch settings (see Page 4/Diagram1).

8. After all the units settings have been set and are plugged in, adjust the sensitivity knob on the

bottom of the master unit to make them react to sound.

Note: Stand-Alone and Master -Slave operation require sound to activate!

DJ Scan™ Set Up Cont.

XLR MALE SOCKET

1 EARTH 2 COLD

HOT 3

XLR FEMALE SOCKET

1 EARTH2 COLD

3 HOT

Figure 2

XLR Pin Configuration:

Pin 1 = Shield

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

DJ Scan™ Operating Instructions

American DJ Supply ®. Los Angeles, CA. 90058 USA DJ Scan Page 3

DMX Operation:

This fixture will react with DMX operation. For best results use only 1 (one) motor function for each

scene (or step), when programming scenes into a DMX controller. This will give you faster mirror and

faster gobo/color changes. For Example:

A. With DMX controller move the mirror up then program the step.

B. Move the mirror down then program that step.

C. Change the gobo/color wheel then program that step.

D. Continue this pattern to achieve best results.

1. Operating through a DMX controller gives the user freedom to create his/her own programs

tailored to their own individual needs. This function also allows you to use your fixtures as spots.

2. This operation will allow you to control each individual fixtures traits with a standard DMX 512

controller such as the American DJ Show Designer™ or the American DJ®DMX Operator.™

3. The DJ Scan™ uses four DMX channels to operate; Channel 1 is Pan, channel 2 is Tilt, channel 3

is Color, and channel 4 Gobos.

4. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard DMX

controller. - Follow the set-up specifications that come with the controller.

1. To focus a DJ Scan,™ it is best to first turn down the music sensitivity knob to its minimum

position.

2. Loosen the thumb screw on the front of the unit that hold the lens in place.

3. Adjust the focus by manually moving the lens up and down.

4. Tighten the thumb screw after you achieve your desired focus.

Lamp Replacement: Caution! Never open the unit when in use. Always disconnect the main power and

allow the unit ample time to cool before attempting to replace the lamp. Remember always replace with

the same type lamp and fuse.

1. Be sure to follow the proper procedures when handling halogen bulbs.

2. Lamp replacement has been made simple by incorporating the use of a removable front cover and

thumb screws.

3. Loosen the thumb screws on front cover.

4. Remove the cover.

5. Remove and replace the bulb.

6. Reassemble.

The American DJ “DJ Scan”™comes with a 1 year limited warranty. We recommend filling out the war-

ranty registration card that came with your fixture to validate your warranty. For service contact your

American DJTM dealer.

DJ Scan™ Operating Instructions cont.

DJ Scan™ Focusing

DJ Scan™ Lamp Replacement

American DJ Supply ®. Los Angeles, CA. 90058 USA DJ Scan Page 4

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out

periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.

2. Use a brush to wipe down the fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every 20 days. Situation may very.

If used heavily in clubs with lots of fog, cleaning may be required more often.

4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.

5. Always be sure to dry all parts completely before plugging the unit in.

Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue,

dust, dew).

DJ Scan™ Cleaning

American DJ Supply ®. Los Angeles, CA. 90058 USA DJ Scan Page 5

Safety Instructions:

1. Be sure not to obstruct cooling vents and keep in a well ventilated area.

2. Take Caution, never to open the fixture when in use!

3. Always disconnect the main power before servicing or replacing the lamp.

4. Always replace with the exact same lamp and fuse.

Options:

1. DJ Scan/ C controller

DJ Scan™ Master-Slave Chart

98765432 1

98765432

98765432 1

98765432

98765432 1

98765432

98765432 1

98765432

DJ Scan™ DMX 512 Chart

98765432 1

98765432

98765432 1

98765432

98765432 1

98765432

98765432 1

98765432

Head 3

Head 2

Master - Head 1

Head 4 Head 16

Head 15

Head 14

Head 13

Head 12

Head 11

Head 10

Head 9

Head 8

Head 7

Head 6

Head 5

American DJ Supply®. Los Angeles, CA. 90058 USA DJ Scan Page 6

Diagram 1

Diagram 2

DMX 512 Traits

Value Value

Value

Channel 1 - Pan Channel 2 - Tilt Channel 3 - Color Channel 4 - Gobo

132

110

232

203

174

145

116

255 255

128 128

242

220

198

176

154

Black Out

Gobo 8

Gobo 7

Gobo 5

Gobo 4

Gobo 3

Gobo 2

Gobo 1

Purple

Pink

Orange

Yellow

Green

Blue

Red

White - Lamp On

45o45o

90o

90o Shutter

Gobo 11

Gobo 10

Gobo 9

American DJ Supply®. Los Angeles, CA. 90058 USA DJ Scan Page 7

Gobo 6

Use the slider adjuster on your DMX controller

to reach your desired DMX value. DMX values

will always range from zero (0) to 255. The

above chart breaks down the “traits” or values

for Color, Gobos, and mirrior movement.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere American DJ Beleuchtungsausrüstung Handbücher

American DJ

American DJ Galaxian 3D Bedienungsanleitung

American DJ

American DJ 3 Sixty 2R Bedienungsanleitung

American DJ

American DJ Whirl 250 Montageanleitung

American DJ

American DJ Micro Gobo Bedienungsanleitung

American DJ

American DJ Titan Bedienungsanleitung

American DJ

American DJ WIFLY BAR QA5 Bedienungsanleitung

American DJ

American DJ Quad Phase Go Bedienungsanleitung

American DJ

American DJ Jelly Fish Bedienungsanleitung

American DJ

American DJ X-Move LED Plus Bedienungsanleitung

American DJ

American DJ Fire Burst DMX Montageanleitung

American DJ

American DJ Inno Pocket Spot Pearl Bedienungsanleitung

American DJ

American DJ Sparkle LED 3W Bedienungsanleitung

American DJ

American DJ Laser Widow Bedienungsanleitung

American DJ

American DJ FREQ 5 Strobe Bedienungsanleitung

American DJ

American DJ Simple Scan Montageanleitung

American DJ

American DJ Pocket Scan Bedienungsanleitung

American DJ

American DJ Spinout Bedienungsanleitung

American DJ

American DJ Ruby Beam Bedienungsanleitung

American DJ

American DJ MARVEL Bedienungsanleitung

American DJ

American DJ Auto Spot 150 Bedienungsanleitung

American DJ

American DJ Avenger ll Bedienungsanleitung

American DJ

American DJ Rampage Bedienungsanleitung

American DJ

American DJ Splitter Bedienungsanleitung

American DJ

American DJ Luna 4 Montageanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung