American Weigh Scales AXIS-100 Bedienungsanleitung
American Weigh Scales
AXIS-100 (100g x 0.01g)
AXIS-650 (650g x 0.01g)
User Manual
AXIS
Copyright © 2012 American Weigh Scales, Inc.
All rights reserved. Rev. 1.0
AXIS Manual
Thank you for purchasing the American Weigh AXIS
digital pocket scale. Please read all operating instructions
carefully before use. Scales are precision measuring devices
and should always be handled with proper care. To ensure
years of reliable service, keep these simple tips in mind:
• Do not exceed the scale’s maximum capacity. This
scale has integrated overload protection, but any
overload protection has its limits!
• Avoid exposure to extreme heat or cold. Scales
perform best at normal room temperature. If
temperatures have changed dramatically, recalibration
may be necessary.
• Allow your scale to warm up for 30-60 seconds before
performing calibration (if available).
• Store your scale in a clean, dry location. Dust, dirt,
and moisture can accumulate on the weighing
sensors and electronics causing inaccuracy or
malfunction.
• Avoid using your scale in close proximity to strong
radio wave emitting devices such as cordless phones.
• Alwaysweighonaatandlevelsurface,freefrom
vibrations and drafts. The corner of a room is usually
the most stable.
• Gently apply all items to be weighed. Do not drop
items onto the weighing platform.
• Avoid dropping your scale. The warranty does not
cover damage due to rough treatment or overload.
• Checkthebatteriesrstifyouarehavinganytrouble
with your scale. This simple step can remedy most
scale issues.
• Calibration should be checked and adjusted
occasionally as part of routine scale maintenance.
I. Part List
1. Scale
2. Cover / Expansion Tray (1 Large, 1 Small)
3. AAA Batteries (x2)
II. Key Description
1. C/R Key - Tap to enter Counting Mode. Hold to set
the piece weight and sample size.
2. Mode Key - Tap to change the weighing unit. Hold
to enter calibration (see section VIII)
3. Tare Key - Re-zero’s the scale. Used to remove the
weight of a container.
4. Power Key - Turns the scale on or off.
III. Battery Installation
Low batteries can cause inaccuracies in digital scales. If
youareexperiencingissueswithyourscale,rsttrynew
batteries. Most times, this will solve the problem.
Proper Battery Installation
2.
1. 3.
4.
g
M
C/R
T
AAA
AAA
g
M
C/R
T
AAA
AAA
AXIS Manual
1. Beforeusingthescaleforthersttime,check
the battery compartment and remove any plastic
insulation strips or packaging that may be in place to
prevent battery drainage during shipping/storage.
2. If you are replacing the batteries, make sure the
positive and negative contacts are properly aligned.
IV. Operation
1. Placethescaleonaat,levelsurfaceandpressthe
key to turn the scale on.
2. Once the start-up process completes and the scale
goes to zero you are ready to weigh.
3. Place the quantity to be weighed onto the weighing
platform.
4. Wait a couple seconds for the display to stabilize
before taking a weight reading.
5. To turn the scale OFF, press the key again.
V. Changing the Unit of Measure
1. Press the Mkey to change the scales displayed unit
of measure.
2. If the scale is turned off then back on, it will default
to the last unit used.
• AXIS-100 & AXIS-650 Units: g (gram) oz (ounce)
ozt (troy ounce) dwt (pennyweight) ct (carat)
gn (grain)
VI. Using the Counting Feature
This scale can be used to count items of uniform weight. To
use the counting feature, follow these instruction:
1. First manually count out a sample quantity of either
25, 50, 75, or 100pcs.
2. With the scale on, place the sample quantity on the
platform then hold the C/R key until a number is
displayed.
3. Press the Mkey to change the displayed number
to match the sample quantity you placed on the
platform (must be 25, 50, 75, or 100)then press the
C/Rkeytoconrmit.
4. The display will then show the current count. The
count will update as you add or remove items.
5. To return to normal weighing mode, press the C/R
key again.
VII. Using the Tare Feature
You can use this scale’s tare feature to subtract the weight
of an empty container or vessel for net weight determination.
NOTE: The weight of the container will subtract from the
available capacity (subtractive taring).
1. Place the empty container or vessel on the weighing
platform.
2. Press the Tkey once. The display will then reset to
zero. If the container is removed, its weight will be
displayed as a negative number.
3. Youmaynowllthecontainerwiththequantityto
be weighed. The display will show the net weight of
the contents.
4. To return to normal weight display (gross weight),
remove any items from the weighing platform and
press the T key again to re-zero the scale.
AXIS Manual
VIII. Calibration
Initial calibration is performed at the factory. However, the
calibration can drift slightly due to stresses from shipping.
Also, due to changes in local acceleration of gravity around
the world, adjustment is recommended when moving the
scale from one location to another. To check calibration:
1. Place the required calibration weight on the scale
and note the displayed value.
2. If the displayed value is not within acceptable
tolerance (see chart on next page), adjustment is
required.
Model Acceptable
Tolerance (±)
Calibration
Weight
Recommended
Accuracy Class
AXIS-100 0.02g 100g OIML M2
AXIS-650 0.2g 500g OIML M2
IX. Adjustment
1. With the scale on, press and hold the Mkey until the
display shows “CAL”.
2. Make sure nothing is on the weighing platform then
press the Mkeyagain.Thedisplaywillash“CAL”
followed by the required calibration weight (see chart
on previous page).
3. Place the required calibration weight on the center
of the platform.
4. Once the weight has stabilized, the scale will show
“PASS” then return to normal weighing mode.
Calibration is complete!
X. Troubleshooting
• Problem: Scale will not turn on
• Solution: Check the batteries and battery contacts.
• Problem: Displayedweightuctuatesrandomly
• Solution: Make sure your workspace is stable and
free of any air currents or vibration. In some cases,
nearby radio wave emitting devices can cause
uctuations.
• Problem: Displayed weight is inaccurate
• Solution: Perform a calibration adjustment. If
you are still having trouble, contact our warranty
department.
XI. Error Codes
1. OUTZ - Zero point has drifted out of the acceptable
range. Try to perform a calibration adjustment. If the
problem persists, the load cell may be permanently
damaged due to overloading.
2. O-Ld - Overload. The maximum capacity has
been exceeded. Remove the extra weight to avoid
permanently damaging the load cell.
3. Lo - Batteries are low. Replace the batteries.
AXIS Manual
American Weigh Scales, Inc.
Norcross, GA 30092
Made In China to our exact
specicationsandqualitycontrol.
XII. Specications
AXIS-100 AXIS-650
Max. Capacity 100g 600g
Readability 0.01g 0.1g
Min. Weight 0.03g 0.2g
Power 2 x 1.5V “AAA” Alkaline
Dimensions 3.4 x 4.0 x 0.8 in.
Platform Dimensions Ø 2.8” in.
Warranty 10 Year Limited Warranty
XIII. Capacity/Readability Charts
AXIS-100 AXIS-650
100g x 0.01g
3.527oz x 0.001oz
3.215ozt x 0.001ozt
64.30dwt x 0.01dwt
500ct x 0.05ct
1543.2gn x 0.2gn
650g x 0.1g
22.92oz x 0.01oz
20.89ozt x 0.01ozt
417.95dwt x 0.1dwt
3250ct x 0.5ct
10031gn x 2gn
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere American Weigh Scales Skala Handbücher
American Weigh Scales
American Weigh Scales AWS-55 Bedienungsanleitung
American Weigh Scales
American Weigh Scales PS-25 Bedienungsanleitung
American Weigh Scales
American Weigh Scales RBS-330 Bedienungsanleitung
American Weigh Scales
American Weigh Scales AWS-Series Bedienungsanleitung
American Weigh Scales
American Weigh Scales ASH TRAY SCALE AT-500 Bedienungsanleitung
American Weigh Scales
American Weigh Scales miniONYX Bedienungsanleitung
American Weigh Scales
American Weigh Scales zx350 Bedienungsanleitung
American Weigh Scales
American Weigh Scales SE-50 Bedienungsanleitung
American Weigh Scales
American Weigh Scales Quicksilver QS-500 Bedienungsanleitung
American Weigh Scales
American Weigh Scales AL-201S Bedienungsanleitung
