AmeriGlide RUBEX Bedienungsanleitung

11819 P/N: 16169 Rev D

WARNING! STRICT ADHERENCE TO THESE INSTALLATION INSTUCTIONS is required and will promote safety of those installing this

product, as well as those who will ultimately use the lift for its intended purpose. Any deviation from these instructions will void the

LIMITED WARRANTY that accompanies the product. Additionally, any party installing the product who deviates from the INSTALLATION

INSTRUCTIONS shall be taken to agree to INDEMNIFY, SAVE AND HOLD HARMLESS the manufacturer from any and all loss, liability or

damage including attorney fees, that might arise out of or in connection with such deviation.

Installation

Manual

RUBEX

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

2 // 16

11819 P/N: 16169 Rev D

Congratulations on your stair lift.

These instructions will assist you in making sure your installation is safe and successful. Please

read through them completely prior to attempting to install the unit.

Indications for Use:

The Rubex Stair Lift is a transport system, also commonly known as a stairway chairlift, or

stairlift. It is a motorized device intended

to assist transfers of a single mobility impaired person up or down a 󲡵ight of stairs.

Congratulations on your stair lift.

These instructions will assist you in making sure your installation is safe and successful.

Please read through them completely prior to attempting to install the unit.

Indications for Use:

The Rubex Stair Lift is a transport system, also commonly known as a stairway chairlift, or

stairlift. It is a motorized device intended to assist transfers of a single mobility impaired person

up or down a 󲡵ight of stairs.

Technical Speci󲡶cations

Weight capacity: 350 lb (over 16'of rail only rated to 250 lb)

Speed: 20 ft/min

Travel: 15'6"Standard, 25'Maximum

Track Type: Extruded Aluminum

Drive: Galvanized Steel Air Craft Cable

Electrical Requirements: 110 VAC 15 AMP

Important!

It is imperative that this manual be read and

understood prior to attempting installation of

the stair lift. Please observe all cautions and

warnings in this manual, as well as on labels

on the equipment.

3 // 16

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

Before you Start ________________________________________ 4

ETL Requirements ______________________________________ 4

Required Tools__________________________________________ 5

Receipt of Unit _________________________________________ 5

Installing the Lower Tracks______________________________ 6

Routing the Lower Call Control Wire _____________________ 9

Installing the Unit_______________________________________ 9

Slack Cable Reset Procedure __________________________ 10

Installing Plastic Chain and Traveling Power Cable _____ 11

Installing the Power Cord ______________________________12

Installing the Lower Limit CAM _________________________12

Installing the Seat _____________________________________13

Installing the Upper Limit CAM_________________________14

Installing the Call Controls _____________________________ 14

Completing Track Installation __________________________ 15

Final Checks___________________________________________15

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

4 // 16

11819 P/N: 16169 Rev D

BEFORE YOU START

Pre-Installation Checklist

□ Is there any visible damage to the packaging? If so, immediately contact the freight

carrier and report the damage.

□ The side of the stairs on which the unit and track will be installed are marked on

the chassis and seat boxes. Verify that you have received the correct hand unit (as

looking up from the bottom of the stairs).

□ Is a properly grounded 110 VOLT, 15 AMP (standard outlet), available within 10'of

the top of the track?

□ Have you “pulled” the necessary permits in your area for installation?

□ Are your stairs made of wood? If not, special mounting hardware will be required.

Contact your dealer for assistance.

□ The track will extend 6"beyond the top step. Is there a door or other obstruction at

the top that will interfere? If so, contact your dealer for assistance.

□ If after reading the instructions, you don’t feel capable or comfortable with

completing the stair lift installation, please contact your dealer for assistance

in 󲡴nding a quali󲡴ed installer in your area.

ETL Requirements

This ETL listed stair lift must meet

the latest ASME A18.1 standards

for the ETL listing to be valid. You

must comply with the following

clauses at the installation site.

ASME Clause 4.1.1*

Lifts shall be installed so that means of egress is

maintained as required by the authority having

jurisdiction.

ASME Clause 4.1.2*

The structure on which the equipment is

installed shall be capable of safely supporting

the loads imposed.

ASME Clause 4.7.2

Limitation of Angle. No lift shall be installed

to operate on a great-er incline than 45° as

measured on the mean.

*Applicable to stair lifts installed in locations other than in or at a private residence.

5 // 16

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

REQUIRED TOOLS

You will need the following tools to complete the installation:

a) 5

32 Allen Wrench

b) 3

8, 7

16 & 9

16 Open-End Wrench

c) Phillips Screwdriver

d) 3

8socket on 8"Extension in an Electric or Cordless Drill

RECEIPT OF UNIT

Your stairway lift will arrive in three boxes that consist of:

Step 1:

a) Seat Box - 38 lb

b) Unit and top 2'track - 115 lb

c) Track Box - 40-80 lb (depending on track length)

Step 2: Check each box for any possible shipping damage.

Caution

Use a dolly or get assistance in carrying the

chassis box to avoid injury.

Note

The chassis is shipped attached to the top 2'of track.

6 // 16 Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

INSTALLING THE LOWER TRACKS

Step 1: Carry the seat box and unit box to the top step and leave aside.

Step 2: Bring the track box to the lower landing

of the staircase. Open the box and remove the

track, track brackets and small parts package.

Step 3: In the small parts package

you will 󲡴nd:

a) track brackets bolts

b) wood screws

c) 2 self-drilling screws

d) call control extension cord and bracket

Step 4: Identify the bottom track section. It will have a metal end plate at

one end. Lay the lower track section on the steps as shown in the picture above.

Note

Top track section will be installed with

the unit after installation of bottom

and mid tracks. It requires 2 brackets.

metal end plate at bottom of stairs

track brackets

7 // 16

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

Step 5: Use the track bracket bolts to fasten brackets to

nuts in the track channel.

Position track brackets as follows:

a) 1 bracket pair on bottom step

b) 1 bracket pair on top step

c) 1 bracket pair above and below where the tracks

splice together

Hand tighten the bolts only - the brackets will need to

slide for correct positioning.

Step 6: Splice bars are used to join the track sections

together. Locate the splice bars and loosen the set screw

from their shipping position. Slide the spice bars to half

way and tighten the two set screws remaining in the track

to hold them in place. The tracks will not slide together if

the set screws protrude beyond the splice bar.

Note

Attach a bracket on the bottom

nut, but leave the nut second

from the bottom unused - it will

be used later.

Caution:

Do not put your 󲡴ngers between the track

sections at any time as injury could occur.

Allen Wrench Allen Wrench

detail of track section showing position of splice bars

do not remove

foam packaging

Step 7: Slide the upper track section onto the

lower track section. Tighten the splice bar set

screws to lock tracks together.

8 // 16 Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

Step 7: Slide the track and brackets toward the

wall or molding. The edge of the track needs to

be positioned 3 1

2"from the wall. If there is an

obstruction on the wall; ie: handrail, window sill,

etc; the track will need to be positioned 3 1

out further than the obstruction. Temporarily set

something (like a book) under the bottom of the

track to raise it 1

2"– 3

4"off the bottom landing.

This will prevent the track from hitting the 󲡷oor

later when the track brackets are tightened.

Step 8: With bracket resting on step, position track

bolt in upper half of track bracket slot.

Step 9: Starting with the bottom step, screw the

bracket half-way down – remove placed obstruction

used to raise track – and 󲡴nish by securely attaching

bracket to the step.

Step 10: Securely tighten remaining track brackets

to the steps using provided wood screws.

Step 11: Track is designed to lay directly on the

step noses, or it can be supported

completely by the track brackets.

Step 12: Pull a piece of string taut from the

top of the track to the bottom. Mark any places

where the string is not parallel with the track.

Check the results by using the string again. Track

and string should now be parallel.

The wall-side of the track may be pulled down

further than the stair side of the track on

steps with thick carpeting/pad. Final track

adjustment should occur after the unit is

installed.

The track should still move vertically in the

bracket slots for 󲡴nal adjustment.

Ilus1. - Track shown

with sagging area

due to “short” step

9 // 16

Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

ROUTING THE LOWER CALL CONTROL WIRE

Step 1: On the wall-side of the track, attach call

control bracket to the second nut up from the

bottom just above the bottom track bracket.

Step 2: Route the wire through the top track

channel on the wallside of the track.

Step 3: At the top of the middle section of track,

tuck the wire underneath the track out of the way.

Step 4: You will 󲡴nish routing the call control wire

after the top track section is in place.

INSTALLING THE UNIT

Step 1: Open unit box by cutting down the sides of the box. Fold the sides

of the box down and slide the unit and top track to the edge of the steps.

Step 2: Remove cardboard packing from back of

footrest.

Step 3: Remove the shipping brace from the

upper section of track and set aside.

Make sure the packing bracket is removed

and discarded before attempting to

operate the lift.

Rave Stair Lift Manual | www.Ameriglide.com | 866-378-6648

Completely remove

the packing bracket.

Caution:

Assistance may be needed for this part of the installation due to

unit’s and upper track section’s weight.

10 // 16 Rubex Stair Lift Install Manual | www.Ameriglide.com | 866-378-6648

11819 P/N: 16169 Rev D

Step 4: Loosen the splice bars from their

shipping position and slide them out to half

way. Tighten the splice bars.

Step 5: Slide the upper track section onto

the lower track section. Tighten the splice

bar set screw bracket to lock tracks together.

The tracks will not slide together if the set

screws protrude beyond the splice bar.

Step 6: Attach track brackets to the side of the

top track section. Hand tighten.

SLACK CABLE RESET PROCEDURE

Step 1: During shipping, the slack cable device may engage and need to be

reset.

Step 2: With the unit and upper track section installed

and power cable unplugged, you will use the hand

crank to turn the motor belt that turns the cable drum.

The illustrations show overhead and cut-away

views of the unit.

Step 3: Place the manual hand crank onto the motor

shaft and rotate clockwise. This will slowly inch the unit up the track.

If you see the lift begin to move uphill or hear a click, that will tell you that the

slack cable has reset.

CAUTION:

Do not put

your 󲡴ngers

between the

track sections

at any time as

injury could

occur.

Andere Handbücher für RUBEX

Inhaltsverzeichnis

Andere AmeriGlide Hebesystem Handbücher

AmeriGlide

AmeriGlide STRATOS Bedienungsanleitung

AmeriGlide

AmeriGlide STRATOS Bedienungsanleitung

AmeriGlide

AmeriGlide Hercules 750 Residential Bedienungsanleitung

AmeriGlide

AmeriGlide HERCULES II 600 Series Bedienungsanleitung

AmeriGlide

AmeriGlide Titan Bedienungsanleitung

AmeriGlide

AmeriGlide Hercules II Hybrid Bedienungsanleitung

AmeriGlide

AmeriGlide Infinity Curved Stair Lift Bedienungsanleitung

AmeriGlide

AmeriGlide PRO DUMBWAITER Bedienungsanleitung

AmeriGlide

AmeriGlide RAVE Handbuch

AmeriGlide

AmeriGlide Stair Lift Bedienungsanleitung

AmeriGlide

AmeriGlide RUBEX Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung