AMI Marine X150 Bedienungsanleitung
Bridge Navigational Watch Alarm System (BNWAS) X150
0801 X150 BNWAS User Manual - Iss02
X150
BRIDGE NAVIGATIONAL WATCH ALARM SYSTEM
(BNWAS)
User Manual
© This Manual and the information contained therein is the property of AMI Marine Ltd.
It must not be reproduced or otherwise disclosed without prior consent in writing from AMI Marine Ltd
BNWAS150 - Bridge Navigational Watch Alarm System
Page 1 of 21
This Page
Intentionally Blank
BNWAS150 - Bridge Navigational Watch Alarm System
Page 2 of 21
Document
Revision
Date
Modification Number (where applicable)
Brief Record of Change and Reason for Change
Iss
0
2
13.09.17
Original
Issue
NOTE:
All alterations must be verified by re-authorisation and approval of the complete document.
AMI MARINE LTD
Unit 9, Crosshouse Centre
Crosshouse Road
Southampton
SO14 5GZ
United Kingdom
Tel No: +44 (0) 23 8048 0450
Web: www.amimarine.com
BNWAS150 - Bridge Navigational Watch Alarm System
Page 3 of 21
This page
Intentionally Blank
BNWAS150 - Bridge Navigational Watch Alarm System
Page 4 of 21
IMPORTANT WARNINGS
DANGER!
RISK OF ELECTRICAL SHOCK!
Disconnect from the power before removing protective covers.
DO NOT remove the covers while the unit is switched on.
24/12 Volt DC electrical power on external units.
NOTICE
Compass safe distance is 1 metre.
NOTICE
No user serviceable parts inside, servicing only by properly qualified
and certified technical staff.
NOTICE
This manual is for informational use only, and may be changed without notice. This manual should not be
construed as a commitment of AMI Marine Ltd. Under no circumstances does AMI Marine Ltd assume any
responsibility or liability for any errors or inaccuracies that may appear in this document. The equipment
should only be used for the purposes intended by the manufacturer; any deviation from this will void the
warranty of the product.
BNWAS150 - Bridge Navigational Watch Alarm System
Page 5 of 21
This page
Intentionally Blank
BNWAS150 - Bridge Navigational Watch Alarm System
Page 6 of 21
CONTENTS
- BNWAS 150 System Overview ..................................................................................... 8
- BNWAS 150 Controls and Functions .......................................................................... 10
- Software Setup and Operation .................................................................................... 12
Switching On The BNWAS 150 .............................................................................. 12
Entering Setup ....................................................................................................... 13
Mode Selection ...................................................................................................... 14
Stage 2 to Stage 3 Delay ....................................................................................... 14
Initial Dormant Period ............................................................................................ 14
Operational Sequence ........................................................................................... 15
Selecting Duty Cabins and Using Cabin Call ......................................................... 16
External Reset ....................................................................................................... 17
Unacknowledged Alarms ....................................................................................... 18
- System Faults ............................................................................................................. 19
- Maintenance guide ...................................................................................................... 20
BNWAS150 - Bridge Navigational Watch Alarm System
Page 7 of 21
This page
Intentionally Blank
BNWAS150 - Bridge Navigational Watch Alarm System
Page 8 of 21
- BNWAS 150 System Overview
The BNWAS 150 system is designed for use on a vessel’s navigation bridge. The remote alarm sounders
cover key locations such as the officer cabins, mess area and ship’s office.
Reset devices can be used on the bridge wings.
The display control and monitoring equipment is to be installed in protected areas inside the bridge.
Dormant Time
This function is adjustable between 3-12 minutes in 1 minute increments only whilst in SETUP mode.
Remote Resets
BNWAS 150 has a reset mechanism which can be activated by a combination of reset pushbuttons and
PIR motion detection sensors.
Fail Alerts
BNWAS 150 has alert messages for Tamper, Power and Battery. Tamper alert is also audible by means of
an on-board buzzer within the display control unit.
Emergency Call and Cabin Call
BNWAS 150 has an Officer call configurable in up to 5 officer cabins within the menu.
Power supply
BNWAS 150 is powered by two separate 24 Volt supplies (main and backup) which will automatically
switch to the backup supply in the event of a main supply failure. This will raise an alarm.
Inputs from Valid Reset Devices & System Alarms
BNWAS 150 provides additional Digital Inputs to accept signals from other devices and transfer alarms.
An external equipment in alarm will send a digital input to the BNWAS and the source will be shown on
LCD display. These might include RADAR or ECDIS.
External valid reset inputs must be approved by the appropriate approval body before being used.
AMI Marine (UK) Ltd will assist with recommendations wherever possible from previous experience but
will not accept responsibility if not accepted.
BNWAS 150 comprises:
Hardware consisting of - Control display panel, interface unit, physical and sensory reset devices, alarm
sounders and beacons.
The BNWAS 150 Software Navigation Menu where the Master can configure and control the operational
mode and parameters of the system.
Overall Layout
There are three areas within the vessel were the system and peripheral units are fitted:-
Wheel house / Bridge
Accommodation Areas
Remote Locations
BNWAS150 - Bridge Navigational Watch Alarm System
Page 9 of 21
Wheel house / Bridge
Equipment - Control display, Stage 1 Alarm sounders, Alarm Beacon, Directional PIR’s, and push button
reset switches. Push buttons can be mounted on the Bridge wing, and are IP rated accordingly.
Accommodation Decks
Equipment - Stage 2 Alarms are located in the accommodation area. The system is configurable through
the navigation menu, for five separate accommodation rooms, labelled: Cabin 1, Cabin 2, Cabin 3, Cabin
4, Cabin 5 - (Captain, Officer 1, 2, 3 and 4) The alarm sounders or sounder beacons can be used.
Remote Locations
Equipment - Stage 3 Alarms are located in remote locations which could include Officer’s mess, Office
locations and Engine Control Room. They can be alarm sounders or sounder beacons.
Inhaltsverzeichnis
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung