Amigo MicroModem Bedienungsanleitung
1
AMIGO
USB MicroModem
Installation Guide
October 25, 2000
2
Section 1
1.0 Introduction
This document provides reference information for the evaluation testing of an external USB modem based
on Host Signal Processing Data/Fax Modem Technology. The evaluation HSP USB Modem™ eliminates
the redundant hardware parts found in most modems today. These include the data pump, a controller, an
additional UART and external memory as required in a conventional approach. In addition, the complete
HSP solution allows an external modem to be upgraded with enhancements and features through software
upgrades rather than a chip change or board swap.
1.1 System Requirements
Pentium 200 MHz MMX Pentium
AMD K6 200 MHz +
Cyrix 6x86MX PR200 +
16MB RAM
Usb port Windows 98 Windows 2000
1.2 Features
DATA
Supported Communication Standards
* V.90, V.34, V.32bis, V.32, V.22bis, V.22, V.21, V.23, Bell212A, Bell 103
Data Compression Error Correction
V.42bis V.42 LAPM
MNP 5 MNP 2,3,4
FAX
Supported Protocols Operating System Compatibility
Group3 T.4 fax, Windows 98
V.17, V.29, V.27ter, V.21 Channel 2 Windows 2000
EIA-578 Fax Class 1
General Features
AT Commands
Auto Fallback
Caller ID
Data/Fax
High throughput Virtual UART, DTE rate up to 115,200
Universal Serial Bus interface
Low power consumption
Signal Quality Monitoring and Auto Retrain
Windows is a registered trademark of Microsoft Corp.
3
Section 2
2.0 USB MicroModem™ Setup using Windows 98 SE
The HSP Modem™ driver will automatically handle all variations of CPU types. This eliminates
the problem of poor performance that results from installing the incorrect driver. The driver will
take advantage of the MMX enhancements if available.
Plug the USB Modem into an USB Bus Cable, it will automatically detect the USB device.
The installation program will begin with the screen shown below. At this point, insert the
USB Modem™ driver disk in the floppy disk drive and click “Next”. Follow the “Wizard”
installation instructions.
2. The installation program will request the “Setup” file. Click “Next”.
4
5
3. Select “Floppy disk drives and click “Next” to continue the installation.
4. Click “Next” to continue the installation.
6
5. Clink “Next” to continue the installation.
7
6 Click “Finish” to continue the installation.
7 Click “Next” to continue the installation.
8 Click “Next” to continue the installation.
8
9 Click “Next” to continue installation.
9
10 Click “Next” to continue installation.
11 Click “Finish” to finish installation.
12.Please according to your “country selection” to
Choose the “international settings.” .
10
AT Command Summary
October 25, 2000
AMIGO
USB MicroModem
Inhaltsverzeichnis
Andere Amigo Modem Handbücher
Beliebte Modem Handbücher anderer Marken
Davicom
Davicom DM562AP Bedienungsanleitung
EpiValley
EpiValley TATA indicom SXC-1080 Bedienungsanleitung
Zte
Zte WiMAX Bedienungsanleitung
Intelimax
Intelimax MA-2060 Bedienungsanleitung
SMC Networks
SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch
Telstra
Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung
US Robotics
US Robotics 3453C Bedienungsanleitung
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung
Zte
Zte MF823 Bedienungsanleitung
Four-Faith
Four-Faith F1403 Bedienungsanleitung
Sierra Wireless
Sierra Wireless AIRLINK MP595W Bedienungsanleitung
Gemtek
Gemtek WiMAX WIXFBR-103 Bedienungsanleitung