Amit IOT400-DL101 Bedienungsanleitung

LoRa Data Logger

IOT400-DL101

User Manual

LoRa Data Logger

Chapter 1 Introduction............................................................................................................................................ 3

1.1 Introduction..............................................................................................................................................3

1.2 Contents List............................................................................................................................................4

1.2.1 Package Contents...........................................................................................................................4

1.2.2 Optional Accessories......................................................................................................................4

1.3 Hardware Configuration ..........................................................................................................................5

1.4 LED Indication.........................................................................................................................................6

1.5 Installation & Maintenance Notice..........................................................................................................6

1.5.1 SYSTEM REQUIREMENTS.......................................................................................................6

1.5.2 WARNING....................................................................................................................................6

1.5.3 HOT SURFACE CAUTION.........................................................................................................8

1.5.4 Product Information for CE RED Requirements..........................................................................9

1.6 Hardware Installation.............................................................................................................................10

1.6.1 Mount the Unit............................................................................................................................10

1.6.2 Connecting I/O Devices..............................................................................................................10

1.6.3 Connecting Console Port for PC Configuration Tool.................................................................13

1.6.4 Connect to external DC Power Source .......................................................................................14

1.6.5 Setup with Windows-based Configuration Tool........................................................................15

Chapter 2 Device Configuration.......................................................................................................................... 17

2.1 Device Status .........................................................................................................................................17

2.2 LoRa Configuration ...............................................................................................................................18

2.3 I/O Configuration...................................................................................................................................23

2.4 Event Configuration...............................................................................................................................25

2.5 System Configuration ............................................................................................................................27

2.6 CLI Console Log.....................................................................................................................................29

Chapter 3 Commands for the LoRa Node............................................................................................................ 30

3.1 Command Basics ...................................................................................................................................30

3.2 Commands .............................................................................................................................................32

LoRa Data Logger

Chapter 1 Introduction

1.1 Introduction

Congratulations on your purchase of this outstanding product: LoRa Data Logger. For IIoT applications, AMIT

LoRa Data Logger is absolutely the right choice. With built-in world-class LoRaWAN module, you can easily

deploy the LoRa Data Logger with LoRaWAN compliant LoRa Gateway / NS / AS for a public or private

LoRaWAN service.

The IOT400-DL101 is a cost-effective low complexity solution for simple data acquisition and wireless

telemetry. LoRa and LoRaWAN are optimized for low bandwidth IoT traffic over wide area to transmit data at

low data rates. It allows massive deployment of wireless IoT with carrier-level security.

Main Features:

Simple device with various interfaces (AI / DI / RS485) for IIoT field data acquisition.

Transfer of field data to associated LoRa Network Server at pre-defined time interval, or on an event at

the site.

Transfer of logged data to designated remote server by schedule rule, or on an event at the site.

Configuring the data logger via a PC with a convenient configuration utility.

Before you install and use this product, please read this manual in detail for fully exploiting the functions of

this product.

LoRa Data Logger

1.2 Contents List

1.2.1 Package Contents

#Standard Package

Items

Description

Contents

Quantity

IOT400-DL101

LoRa Data Logger

1pcs

LoRa Antenna

1pcs

Terminal Block

1pcs

499 Ohm Resistor

1pcs

Power Adapter

1pcs

1.2.2 Optional Accessories

#Optional parts (these parts are sold separately)

Items

Description

Contents

Quantity

USB-to-Serial Console Cable

1pcs

Extender

1pcs or 2 pcs

(1 pcs needed for din-rail and 2 pcs

needed for wall-mount)

DIN-Rail Bracket

1pcs

LoRa Data Logger

Wall Mount Kit

2pcs/set

1.3 Hardware Configuration

Left View

Right View

※Reset Button

RESET button provides user a quick and easy way to resort the default setting. Press the RESET button

continuously for 6 seconds, and then release it. The device will restore to factory default settings.

LoRa

Antenna

Reset

Button

LoRa Data Logger

1.4 LED Indication

Indication

LED Color

Description

Blue + Red

OFF: Device power is off

Red Steady on: Device is powered ON, but LoRa module is not ready yet.

Blue Steady Flash: Device is powered ON, and LoRa module is ready.

Red and Blue Steady ON: Device is in Recovery mode, or FW is upgrading.

1.5 Installation & Maintenance Notice

1.5.1 SYSTEM REQUIREMENTS

Network Requirements

LoRaWAN compliant Gateway and Network Server

Configuration Tool Requirements

Computer with the following:

Windows®7 or Windows 10

An installed Ethernet adapter

A USB 2.0, or later for device configuration

1.5.2 WARNING



Only use external DC Power Supply that complies to

device spec. Using a different voltage rating power

adaptor is dangerous and may damage the product.

Do not open or repair the enclosure by yourself. If

the product is too hot or malfunctioning, turn off the

device and have it repaired at a qualified service

center.

Place the product on a stable surface, or screwed it

on a solid plate or wall.

Attention

LoRa Data Logger

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FOR PORTABLE DEVICE USAGE (<20m from body/SAR needed)

Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for

intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be

kept as far as possible from the user body or set the device to lower output power if such function is available.

FOR MOBILE DEVICE USAGE (>20cm/low power)

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES)

Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all

WiFi product marketed in US must fixed to US operation channels only.

LoRa Data Logger

1.5.3 HOT SURFACE CAUTION

CAUTION: The surface temperature for the metallic enclosure can be very high!

Especially after operating for a long time, installed at a closed cabinet

without air conditioning support, or in a high ambient temperature

space.

DO NOT touch the hot surface while servicing!!

LoRa Data Logger

1.5.4 Product Information for CE RED Requirements

The following product information is required to be presented in product User Manual for latest CE RED

requirements.

(1) Frequency Band & Maximum Power

1. Frequency Band for LoRa Connection

Band

Operating Frequency

Max. Output Power

EU868

863 - 870MHz

100 mW (20dBm)

(2) DoC Information

You can get the DoC information of this product from the following URL:

http://www.amitwireless.com/products-doc/

(3) RF Exposure Statements

The antenna of the product, under normal use condition, is at least 20 cm away from the body of user.

(4) Unit Mounting Notice

The product is suitable for mounting at heights <= 2m (approx. 6 ft), or in a cabinet.

Ensure the unit is fixed tightly to reduce the likelihood of injury due to exposure to mechanical hazards if

dropped.

(5) Manufacture Information

Manufacture Name: AMIT Wireless Inc.

Manufacture Address: No. 28, Lane 31, Sec. 1, Huandong Rd., Xinshi Dist., Tainan 74146, Taiwan (R.O.C.)

The information presented in this section is ONLY valid for the EU/EFTA regional version. For those non-

CE/EFTA versions, please refer to the corresponding product specification.

LoRa Data Logger

1.6 Hardware Installation

This chapter describes how to install and configure the hardware

1.6.1 Mount the Unit

The IOT400 series products can be placed on a desktop, or use extender to place on DIN-Rail bracket or mount

on the wall.

1.6.2Connecting I/O Devices

The IOT400-DL101 provides a 10-pin terminal block for one serial console port, one digital input (DI), one

digital output (DO), one analog input (AI), and DC Power (DC5~12V) ports. Connect the field device(s) to the

I/O ports with the right pin assignments as shown below.

DO-

DI-

UART TX

UART RX

GND

DO+

DI+

GND

PWR

Mode

Specification

Analog Input

0-10V analog Voltage

with 12-bit ADC, sample rate upto 125kHz;

+/- 2.5mV precision

Digital Input

(Isolated)

Trigger Voltage (high)

Logic level 1: 2V~25V

Normal Voltage (low)

Logic level 0: 0V~1V, or floating

Digital Output

(Isolated)

Voltage

(Non-Relayed Mode)

Maximum 24V/300mA

(Depends on external device)

If the AI signal range of your device will run out off the design spec. of Data Logger (0-10V), you have to add a

certain scaling circuit to prevent overflow readings and even damage the Data Logger.

Inhaltsverzeichnis

Andere Amit Datenlogger Handbücher

Amit

Amit LoRa IOT400-DL3B1 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung