AMPTech 3 Bedienungsanleitung
SOFTCLOSE AUTOMATIC
MODEL 3
INSTALLATION INSTRUCTIONS
V. M3 SOC20-MKIII
Table of Contents
About these instructions 3
Preparations 5
List of the tools required for the installation 5
List of the scope of delivery 6
Installation 7
Remove the door panel from 7
Remove the window paneRemove the 9
Plastic the door 11
Replace the lock unit and cabling 13
Power supply 20
Installation of the rear door 28
System test 33
Checklist 34
Dismantling 35
2
About these instructions
Product descriptions
All specifications and descriptions of the products in this installation
manual were verified and checked at the time of creation and applied to
the respective versions in the manual named version. We reserve the right
to modify and improve the products at any time.
Errors and inaccuracies
If you notice any errors or inaccuracies in this installation guide, or if you
notice that some descriptions are not complete, please use the following
email for your feedback: feedback@amptech.store.
Copyright
This document is protected by copyright and is the intellectual property of
AMP Engineering GmbH. The contents of this manual may not be
modified, reproduced or copied in whole or in part without the express
written consent of AMP Engineering GmbH. Likewise, the commercial use
of this manual is prohibited.
Safety instructions
The Softclose automatic system has been designed to enable convenient
and safe opening and closing of the doors. Nevertheless, as such it does
not replace visual inspection. Therefore, always check that the doors are
closed before starting a journey or when removing yourself from your Tesla.
In any case, the safety instructions marked "
🚫
CAUTION:..." in these
instructions must be observed. In case of disregarding the safety
instructions and resulting damages to the AMPTech components or even
vehicle parts, the warranty claim as well as any liability for damages or
consequential damages expires due to own fault (see GTC's on
www.amptech.store/agb/, V. Liability). If you have any questions or
problems with the Softclose automatic, please contact AMPTech under the
phone number +49 40 60 77 34870 or the e-mail [email protected]ore.
3
Preparations
To ensure that the installation can be carried out quickly, tools required for
the installation should be provided before starting. The tools required are
listed below.
List of required tools for the installation
tool list
Position
Description
1
chuck
2
soft surface (ceiling o. Ä.)
4
Shear
5
Plastikmontierhebel
7
ratchet / ratchet
8
socket set / nut
9
cordless screwdriver
10
tape
11
cutting tool (knife)
12
Torx set
13
flashlight
14
tape
15
antirust
16
cable lubricant
17
guidewire
18
Alubutyl
💡
Tip
A commercially available toolbox contains many of the
tools you need.
4
Please check the scope of delivery of the order before starting the
installation.
List on the package
delivery
Position
Description
1
4 SoftClose motors
2
4 lock units
3
4 harnesses
4
4 support rails
5
6 screws
6
12 rubber stopper
7
4 plastic caps
8
Power Splitter Y-cable
9
2x power supply harnesses
10
cable tie
After checking the contents and the provision of tools can be continued
with the installation instructions
5
Installation instructions
Before proceeding to the removal of the door panels and footwell trim, it is
advisable to expose storage areas for the parts removed during the
installation. In addition, it is helpful to keep the clamps and screws that will
be removed sorted.
These installation instructions describe the installation of the softclose
mechanism on the two doors of the vehicle on the left in the direction of
travel. On the right-hand side of the vehicle in the direction of travel, the
installation is identical and can therefore be carried out according to the
same instructions.
💡
Tip
Start the installation from the driver's door.
Remove the door mounting lining Remove lever
levering
●Remove the tweeter with a plastic mounting lever by placing the
plastic mounting lever below the speaker and levering it upward
(Figure 1
Figure 1: Levering the tweeter
Installation Guide
●Loosen the connector plug behind the speaker. This is locked with a
barb. To do this, lever the plug with a flat-blade screwdriver and pull
the plug out at the same time (Figure 2)
Figure 2: Loosening the bar mounting
●Lever out the reflector on the outside of the driver's door with a
plastic mounting lever (Figure 3)
Figure 3: Removing the reflector
●Loosen the plastic cover on the bottom of the door panel armrest
(Figure 5).
●Loosen all three screws (T27, Torx) used to secure the door trim.
These are located under the reflector, underneath the removed
plastic cover and underneath the door armrest (Figure 4, 5 and 6)
7
Installation Guide
Figure 4 (left), Figure 5 (center), Figure 6 (right):to be
Screws Removed from the door panel
●Slide a plastic mounting lever under the door panel and reach under
the door panel at the bottom of the door panel with both hands. Pull
the door trim jerkily with both hands to release it. The door trim is
hooked at the upper end. You can lift the door trim out upwards.
●Feed the tweeter cable through the grommet
●Remove the felt cover so that you can access the bowden cable and
the plug connections of the cable harness.
💡
Tip
The felt cover is susceptible to cracking. Therefore,
remove the felt cover carefully.
●Remove the Bowden cable from the device.
●Loosen all the clamps with which the wiring harness is attached to
the door trim.
●Loosen the plug connections. These are connected according to the
barb principle
window pane remove
●connecting the plug of the window pane the motor (Figure 7)
8
Installation Guide
Figure 7: plug of the window pane motor
●Remove the two rubber seals on the door (Figure 8). Depending on
the position, the window pane itself or the frame of the window pane
can be seen behind the rubber seals
Figure 8: rubber seals
●Position the window pane so that both screws in the window pane
socket can be seen through the opening
●Disconnect the window pane motor connector. You can place the
door panel on an exposed storage surface
💡
Tip
Mark the position of the window pane (e.g. with
insulating tape). This way you can put the window back
in the same position later.
9
Installation Guide
●Loosen both screws from the window pane socket (14mm,
hexagonal). A second person should hold the window pane at all
times (Figure 9).
🚫
Attention: After the door panel and all plugs have been
loosened, the window moves higher than normal. The door must therefore
no longer be closed to prevent the window pane from hitting the chrome
strip!
🚫
Attention: Should Remove the window panes second person be
called in to!
Figure 9: Removing the screws in the window frame
●Remove the seal from the window pane. This is fixed at the outer end
with plastic clips in the door casserole and can be lifted up after
these have been released.
●Carefully lift the window pane out of the door and place it on a safe
surface.
💡
Tip
Tilt direction of the window pane in thewhen curvature
lifting it out.
Remove the plastic cover from the door.
●Disconnect the connectors below the tweeter that has already been
removed (Figure 10). These connectors must also be disconnected
from the rail below. To do this, lever the retainer of the plugs out of
the barb on the underside of the plugs and then slide the plugs
downwards out of the rail. The blue-colored plug in Figure 10 is not
held by a barb
10
Inhaltsverzeichnis
