Amroad AMROAD P3 Bedienungsanleitung

AMROAD P3

DOOR STATION

Installation Manual

AMROAD P3

Contents

Contents............................................. i

Package Contents...............................1

Rear Side ........................................... 2

Reset Button .................................................2

Installing Procedures......................... 3

Wire and Cable Connection..........................3

Install Main Unit .......................................... 4

IO Application ................................... 5

Electric Bolt.................................................. 5

Electric Strike ............................................... 6

PIR Motion Sensor and Light ........................7

Contents

AMROAD P3

Package Contents

1. Front panel

2. Main unit

3. 2-pin terminal block + cord end terminal ×2

4. 5-pin terminal block + cord end terminal ×5

5. H type terminal connector for power cord

6. Screws for firmness in solid concrete M4-L35

×4

7. Pin-Torx security screws M4-L10 ×2

8. Long Phillips screws M4-L55×4

9. Relay

10. L-shaped screw driver for security screws

11. Wall plugs ×4 + self tapping screws ×4

12. Blank RFID card

Package Contents

AMROAD P3

Rear Side

Reset Button

1. The device will be switched to the static IP

mode and reboot itself when the user has

pressed the reset button for 3 seconds. IP is

"192.168.0.50".

2. When the button has been pressed for

more than 6 seconds, the device will be

switched to the DHCP mode and reboot

itself (the users need to restore the factory

setting).

Rear Side

AMROAD P3

Installing Procedures

Wire and Cable Connection

1. Connect Power cord with 2-Pin terminal

block + cord end terminal together, and

insert it into DC 12V INPUT PORT.

2. Insert Ethernet cable into Ethernet port

according to the diagram above.

3. Connect the black wire (ground wire) to

the Mountingl Box. Remember to tighten

the screws on both sides. In order to

prevent power surge and lighting strike

from damaging the device, the Mountingl

Box should be connected to the earth wire

of the building.

4. For more information regarding to DI/DO

applications, please read P.5-7(IO

Application) for reference.

Installing Procedures

ire and Cable Connection

AMROAD P3

Install Main Unit

1. Place the main unit into the Mounting Box

and tighten four Phillips screws(M4-L35) .

2. Firmly press the front panel against the

device until the panel touches the wall.

3. Use the tool lift the doorbell button and

tighten 2 security screws (M4-L10) with the

L-shaped key.

4. Close the key by pressing it until it snaps.

5. Do not rip the plastic cover in order to

protect the front panel.

Installing Procedures

AMROAD P3

IO Application

Electric Bolt

The Electric Bolt is closed when +12 V is

supplied.

The Electric Bolt is opened when +12V is

not supplied.

DI1：The magnetic reed equipment should

set Low (HighLow), DI1 is used to detect

whether the door is closed well.

When the electronic circuit connected

with the Electric Bolt completely, you

should choose “Positive” in the item

Device Relay Output on the WEB UI in

Entrance Setting – GPIO, and saved.

Please follow Technical Manual to set

WEB UI.

IO Application

Electric

Bolt

AMROAD P3

Electric Strike

The Electric Strike is opened when +12 V is

supplied.

The Electric Strike is closed when +12V is

not supplied.

DI1：The magnetic reed equipment should

set Low (HighLow), DI1 is used to detect

whether the magnetic reed is revert.

When the electronic circuit connected

with the Electric Strike completely, you

should choose “Negative” in the item

Device Relay Output on the WEB UI in

Entrance Setting – GPIO, and saved.

Please follow Technical Manual to set

WEB UI.

產品應用

陰極鎖

IO Application

Electric

Strike

AMROAD P3

PIR Motion Sensor and Light

AMROAD P3 can also connect PIR (Passive

Infrared) motion sensor and Light. PIR

motion sensor detect whether person (or

living things) moves within the sensor range.

Once PIR motion sensor detects person (or

living things) moves, it will trigger the Light

to be turn on for 30 seconds.

DO2 Service

Device Relay Output：The way to detect set

High. If DI2 is triggered, DO2 will light up for

30 seconds automatically.

Trigger By Digital Input 2：The way to detect

set High (LowHigh). DI2 is used to connect

to PIR (Movement Detector, Intruder

Detector).

Please follow Technical Manual to set

WEB UI.

產品應用

PIR Motion Sensor and Light

IO Application

PIR Motion Sensor and Light

Andere Handbücher für AMROAD P3

Inhaltsverzeichnis

Andere Amroad Gegensprechanlage Handbücher

Amroad

Amroad DP101 Kurzanleitung zur Einrichtung

Amroad

Amroad DP101 Bedienungsanleitung

Amroad

Amroad DP3210 Bedienungsanleitung

Amroad

Amroad AMROAD P3 Bedienungsanleitung

Amroad

Amroad DP101 Bedienungsanleitung

Amroad

Amroad XL COMMUNITY STATION Bedienungsanleitung

Amroad

Amroad DP3211 Bedienungsanleitung

Amroad

Amroad DP100-25 Bedienungsanleitung

Amroad

Amroad VP115 Bedienungsanleitung

Amroad

Amroad ID5101 Bedienungsanleitung

Amroad

Amroad DP100 Bedienungsanleitung

Amroad

Amroad DP3211 Bedienungsanleitung

Amroad

Amroad AMROAD P3 Bedienungsanleitung

Amroad

Amroad DP3010R Benutzerhandbuch

Amroad

Amroad DP3210 Bedienungsanleitung

Amroad

Amroad ID5101 Bedienungsanleitung

Amroad

Amroad DP3010R Bedienungsanleitung

Amroad

Amroad DP101R Bedienungsanleitung

Amroad

Amroad ID5101-RN Bedienungsanleitung

Amroad

Amroad DP3210 Bedienungsanleitung

Amroad

Amroad DB3100R Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung