AMX AXC-TEMP AND RTS-1 TEMPERATURE CONTROL CARD AND ROOM TEMPERATURE... Bedienungsanleitung

instruction manual

Axcess Control Cards

AXC-TEMP

Temperature Control Card and RTS-1

Room Temperature Sensor

Limited Warranty and Disclaimer

AMX Corporation warrants its products to be free from defects in material and workmanship under normal use for a

period of three years from date of purchase from AMX Corporation, with the following exceptions. Electrolumines-

cent and LCD control panels are warranted for a period of three years, except for the display and touch overlay com-

ponents which are warranted for a period of one year. Disk drive mechanisms, pan/tilt heads, power supplies,

modifications, MX Series products, and KC Series products are warranted for a period of one year. Unless otherwise

specified, OEM and custom products are covered for a period of one year. AMX Corporation software products are

warranted for a period of 90 days. Batteries and incandescent lamps are not covered.

This warranty extends to products purchased directly from AMX Corporation or an authorized AMX Corporation

dealer. Consumers should inquire from selling dealer as to the nature and extent of the dealer’s warranty, if any.

AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform,

including any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable

for any claim made by a third party or made by you for a third party.

This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort

claim (including negligence and strict product liability), a contract claim, or any other claim. This limitation of liabil-

ity cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation

or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This

limitation of liability, however, will not apply to claims for personal injury.

Some states do not allow a limitation of how long an implied warranty lasts. Some states do not allow the limitation

or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion

of the Limited Warranty may not apply to you. This Limited Warranty gives you specific legal rights. You may also

have other rights that may vary from state to state. You are advised to consult applicable state laws for full determina-

tion of your rights.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WAR-

RANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FIT-

NESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT

STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE

LIMITED TO THE TERMS OF THIS LIMITED WARRANTY.

Table of Contents

AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

Table of Contents

Product Information .................................................................................................1

Features ............................................................................................................................ 1

Pre-Installation ..........................................................................................................3

Setting Fahrenheit or Celsius ............................................................................................ 3

Setting the Jumpers ................................................................................................................. 3

Calibrating POTs ............................................................................................................... 4

Connecting Multiple RTS1s............................................................................................... 4

RTS1 Preparation.............................................................................................................. 5

Wiring the RTS1....................................................................................................................... 5

RTS1 Calibration ............................................................................................................... 6

Testing the RTS1 .............................................................................................................. 7

Programming ............................................................................................................9

ii AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

Table of Contents

Product Information

AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

Product Information

The AXC-TEMP Temperature Control card (FIG. 1) provides control and power

for the RTS1 Room Temperature Sensor (FIG. 2). The RTS1 provides precision

temperature sensing for the AXT-TEMP.

Features

The AXC-TEMP features include:

! Standard Axcess CardFrame slot size

! Settings for Fahrenheit or Celsius operation

! Control and power for up to four independent RTS1 units

! Measurement accuracy of +/- 2°F (+/- 1.1°C)

! Calibration for zero temperature deviation

The RTS1 features include:

! Precise temperature measurement from 5× to 128°F (-29.2× to +106.9°C)

! Connection to the AXC-TEMP card with a shielded 3-conductor cable

FIG. 1 AXC-TEMP

FIG. 2 RTS1

Product Information

2AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

The table below lists the specifications for the AXC-TEMP and RTS1.

Specifications

AXC-TEMP

Input voltage +12 to 18 VDC

Current Draw 40 mA (using four RTS1s = 75 mA)

Temperature range 0.0 ° F to +250 ° F (0.0 ° C to +106.9 ° C)

Accuracy +/-2 ° F (+/-1.1 ° C)

Resolution 10-bit (1024 steps over range)

RTS1

Weight 3.2 oz. (91 grams)

Dimensions 4.5" x 2.75" x 9" (114 mm x 70 mm x 23 mm)

Enclosure Metal, off-white finish

Resolution 10-bit (1024 steps over range)

Temperature range -20.5°F to +250°F (-29.2°C to 106.9°C)

Pre-Installation

AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

Pre-Installation

Before installing the AXT-TEMP and RTS1, you must properly set jumpers and

potentiometers (POTs).

Setting Fahrenheit or Celsius

Set the Fahrenheit or Celsius feature by manually selecting each jumper (JP1- JP4) or by manually

selecting the RAW A/D OUTPUT jumper on the card. FIG. 3 shows the location of the jumpers and

POTs. The RAW A/D OUTPUT jumper overrides jumpers JP1 - JP4.

Setting the Jumpers

Use the two-position jumpers (FIG. 4) to select Fahrenheit or Celsius operation. The setting takes

effect when you power on the system or reinsert the card into the CardFrame. The default setting is

Fahrenheit (°F).

1. Set each jumper (JP1 - JP4) on the card for either Fahrenheit or Celsius.

2. Set all calibration POTs to zero. Each POT is a 25 turn POT. Full counter-clockwise is a -4°

variance and full clockwise is a +4° variance.

3. Insert the card into the desired Axcess CardFrame slot. It is not necessary to disconnect power

to the CardFrame when installing the card.

FIG. 3 Location of jumpers and POTs

FIG. 4 Jumpers

Channels 1 - 4

Jumpers JP1 - JP4 and

JP13 (RAW)

Jumpers JP5 - JP8

Jumpers JP9 - JP12

°F

°C

JP1

To access the jumper and POTs, remove the AXC-TEMP card from the CardFrame.

After making all adjustments, be sure to reseat the card properly. You can also adjust

the card using an optional Axcess Extender Card (AXC-EXTN), for easier access.

Pre-Installation

4AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

4. Hold the card by the tab end and slide the card into the frame. Make sure the card is correctly

positioned in the guide slot.

5. Gently push the card in until it is firmly seated in the card connector slot. It is not necessary to

disconnect the power to the CardFrame when installing the card.

Calibrating POTs

Use the four calibration potentiometers (POTs), marked CH 1 - CH 4, to adjust the respective RTS1

units 1 - 4. The default setting for each POT pointer is 0°. The table below describes the POT

calibration for CH 1 - CH 4.

Connecting Multiple RTS1s

FIG. 5 shows the pinout for the AXC-TEMP when connecting multiple RTS1s.

Calibration POTs CH1 - CH4

POTs Description

R1 Offsets input CHAN1 by -4 to +4 degrees

R8 Offsets input CHAN 2 by -4 to +4 degrees

R2 Offsets input CHAN 3 by -4 to +4 degrees

R9 Offsets input CHAN 4 by -4 to +4 degrees

R33 Stops Adj for input CHAN 1 (for RTS2 only)

R34 Stops Adj for input CHAN 2 (for RTS2 only)

R35 Stops Adj for input CHAN 3 (for RTS2 only)

R36 Stops Adj for input CHAN 4 (for RTS2 only)

FIG. 5 AXC-TEMP pinout for multiple RTS1s

PIN 1

PIN 16

IN3

IN4

GND

IN1

PWR

GND

IN2

GND

PWR

TO RTS1 #1

TO RTS1 #2

TO RTS1 #3

TO RTS1 #4

Pre-Installation

AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

RTS1 Preparation

To install the RTS1 units:

1. Wire RTS1 units 1 - 4. Refer to Wiring the RTS1 for additional information.

2. Check the temperature.

! If the panel has a display, check the temperature readings on the system Wiring control

panel. The temperature readings will change when the room temperature changes by a

half degree.

! If the panel does not have a display, check the variables in Axcess.

Wiring the RTS1

Use Belden 8723 or equivalent cable. When an application or code requires plenum-rated cable, use

Belden 88723 or equivalent cable.

Call AMX Technical Support for any installations that require a wire run of more than 100 feet.

FIG. 6 RTS1 circuit connections

2.75" (69.9 mm)

w/ front cover on

4.5"

(114.3 mm)

RTS1 backplate

Wire feed hole

RTS1 circuit board

AXlink connector

From left to right:

GND, OUT, PWR

RTS1 depth is 0.9"

(22.9 mm) with the

front cover installed

Pre-Installation

6AXC-TEMP Temperature Control Card and RTS1 Room Temperature Sensor

RTS1 Calibration

To calibrate the RTS1:

1. Place a reference thermometer near RTS1 unit 1.

2. Allow the reference thermometer to stabilize for approximately 1-minute.

3. Adjust calibration POT R1 (CHAN 1) clockwise or counter-clockwise to match the reference

thermometer temperature.

4. Touch the sensor at bottom of RTS1 unit 1 for 2-seconds to force a temperature change.

5. Wait approximately 5 seconds for the temperature to stabilize. Then, recheck the display panel

temperature display. Allow the reference thermometer to stabilize approximately one minute,

then check.

6. If necessary, repeat steps 1 - 5 for RTS1 units 2 - 4, and move the reference thermometer near

each sensor you are calibrating.

FIG. 7 RTS1 to Axcess Cardframe connections

Input White

Green

Drain

Ground Black

Power Red

Input White

Green

Drain

Ground Black

Power Red

Input White

Green

Drain

Ground Black

Power Red

Input White

Green

Drain

Ground Black

Power Red

Green

Drain

Black Ground

Red Power

White Output

Green

Drain

Black Ground

Red Power

White Output

Green

Drain

Black Ground

Red Power

White Output

Green

Drain

Black Ground

Red Power

White Output

Belden 8723,

or equivalent

(Twisted Pair)

Belden 8723,

or equivalent

(Twisted Pair)

Belden 8723,

or equivalent

(Twisted Pair)

Belden 8723,

or equivalent

(Twisted Pair)

RTS1 Unit 1

RTS1 Unit 2

RTS1 Unit 3

RTS1 Unit 4

AXC-TEMP

Axcess

CardFrame

When connecting wiring, ensure the Drain and Green wires are used. The

capacitance/filtering effects of these wires are required for accurate measurements.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AMX Temperaturregler Handbücher

AMX

AMX VST-TSO Leitfaden

AMX

AMX VST-TSF Leitfaden

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema