Analog Devices ADuCM360 Bedienungsanleitung

Getting Started Guide

ADuCM360/ADuCM361

One Technology Way •P. O. Box 9106 •Norwood, MA 02062-9106, U.S.A. •Tel: 781.329.4700 •Fax: 781.461.3113 •www.analog.com

ADuCM360 Development Systems

Getting Started Tutorial

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS.Rev. A | Page 1 of 16

INTRODUCTION

The ADuCM360 is a fully integrated, 4 kSPS, 24-bit data

acquisition system that incorporates dual, high performance

multichannel sigma-delta (Σ-Δ) analog-to-digital converters

(ADCs), a 32-bit ARM Cortex™-M3 processor, and Flash/EE

memory on a single chip.

The ADuCM360 is designed for direct interfacing to external

precision sensors in both wired and battery-powered appli-

cations. The ADuCM361 contains all the features of the

ADuCM360 except for the ADC0, which was removed.

Refer to the ADuCM360/ADuCM361 product page for future

updates.

Additional support for the ADuCM360/ADuCM361 is available

through the EngineerZone®website.

GENERAL DESCRIPTION

The ADuCM360 development system allows evaluation of

ADuCM360 silicon. This getting started guide introduces the

support features and the tools supplied with the evaluation

kit. In addition, it shows and describes how to connect the

evaluation hardware.

This guide describes the software files that are included on

the DVD and FTP site, and how to download them. The FTP

site, should be opened in Windows® Explorer.

This guide works as a tutorial by providing a step-by-step

account of how to download evaluation versions of third-

party software tools. Instructions are provided on how to load

code examples that are supplied on the CD and on the FTP

site. These examples demonstrate simple operation of the

ADuCM360.

Working through this guide brings the user to the stage where

they can start to generate and download their own user code

for use in their own unique end-system requirements.

Figure 1. ADuCM360 Mini-Board Connected to Analog Devices, Inc., J-Link OB Emulator

10952-001

Downloaded from Arrow.com.

ADuCM360/ADuCM361 Getting Started Guide

Rev. A | Page 2 of 16

TABLE OF CONTENTS

Introduction ...................................................................................... 1

General Description ......................................................................... 1

Revision History ............................................................................... 2

Development System Contents....................................................... 3

Evaluation Board .......................................................................... 3

J-Link OB Emulator ..................................................................... 3

Connecting the Hardware........................................................... 3

Software Installation......................................................................... 4

Software Content Provided......................................................... 4

Software Installation Instructions.............................................. 4

Programs Installed ....................................................................... 5

Keil µVision4 Integrated Development Environment ................. 6

Introduction...................................................................................6

Quick Start Steps ...........................................................................6

Extra Optional Details on µVision..............................................7

IAR Embedded Workbench IDE.................................................. 12

Starting IAR Embedded Workbench....................................... 12

Quick Start Steps ........................................................................ 12

Elves.................................................................................................. 14

Using Elves.exe with µVision4 ................................................. 14

Windows Serial Downloader........................................................ 15

Preparing for Download ........................................................... 15

Downloading Using CM3WSD................................................ 15

Running the Downloaded File ................................................. 15

REVISION HISTORY

4/13—Rev. 0 to Rev. A

Changes to Interface Board, Emulator, and Software....Universal

Replaced All Sections, Tables, and Figures .....................Universal

9/12—Revision 0: Initial Version

Downloaded from Arrow.com.Downloaded from Arrow.com.

Getting Started Guide ADuCM360/ADuCM361

Rev. A | Page 3 of 16

DEVELOPMENT SYSTEM CONTENTS

The E VA L -ADuCM360QSPZ is an evaluation kit for the

ADuCM360 and ADuCM361. This kit features a mini-board

(E VA L-ADuCM360MKZ) and an Analog Devices J-Link OB

emulator (USB-SWD/UART-EMUZ) that connects to a PC

USB port via a USB cable. A comprehensive set of development

tools is included on the DVD.

Figure 2. ADuCM360 Mini-Board Connected to J-Link OB Emulator

The development system contains the following:

•An ADuCM360 mini-board

•An Analog Devices J-Link OB emulator

•1 USB cable

•A DVD.

EVALUATION BOARD

The E VA L -ADuCM360MKZ mini-board facilitates

performance evaluation of the device with a minimum of

external components. The board schematic is available after

installation of the software in the documentation folder.

By default, this is

\ADuCMxxxV1.3\Documentation\ADuCM360\Evaluation

Board\Eval-ADuCM360MKZ.

J-LINK OB EMULATOR

The J-Link OB emulator provides nonintrusive emulation via a

serial wire, and also provides supply and UART communication

with the ADuCM360 mini-board. Figure 3 shows a top view of

the emulator board. J2 connector plugs into the ADuCM360

mini board. The J2 connector pinout is shown in Figure 4.

Figure 3. Emulator Top View

Figure 4. J2 Connector

For downloading and debugging, LK1, LK2, LK4, and LK6 must

be inserted. LK3 and LK5 are required to communicate via

UA RT. Required software for the J-Link OB is included in the

software installation.

Note that the J-Link OB emulator replaces the J-Link Lite and

related interface boards previously shipped with the ADuCM360

development system.

CONNECTING THE HARDWARE

Do not plug in the emulator and mini-board before the software

is installed. See the Software Installation section.

10952-002

10952-003

10952-004

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADuCM360/ADuCM361 Getting Started Guide

Rev. A | Page 4 of 16

SOFTWARE INSTALLATION

A DVD is included in the development system. The DVD

content is also available for download on the FTP site.

SOFTWARE CONTENT PROVIDED

Table 1 shows the tools provided on the DVD.

Table 1. Tools

Tools Functions

Keil µVision For compiling/debugging and code

development, a 32 kB limited version

IAR Embedded

Workbench

For compiling/debugging and code

development, a 32 kB limited version

Segger J-Link

Software

J-Link software and documentation pack

includes USB drivers for the emulator, J-Link

Commander, J-Mem, and so on

CM3WSD This utility accepts a hex file and allows it to

be downloaded via the USB interface to the

ADuCM360 device on your evaluation board

Elves Elves.exe is an application that helps a

C programmer choose appropriate functions

from Analog Devices libraries and simplifies

deciding which values to place in the

function parameters.

SOFTWARE INSTALLATION INSTRUCTIONS

Perform the steps described in this section before plugging any

of the USB devices into the PC.

1. Close all open applications.

2. Insert the development system DVD into your DVD drive.

Optionally, download the ADuCMxxxV1.3 folder from

the FTP and save it to your machine using the same folder

structure as on the FTP site. To reduce the download time,

consider excluding either the IAR or Keil folders

depending on which development environment you chose

to use.

3. Double-click on ADuCMxxxV1.3.exe and follow the on-

screen instructions. A menu displays installation options as

shown in Figure 5.

Figure 5. Installation Options

You can choose to install Keil and/or IAR tools as part of

the installation, or at later stage by launching

•mdk470.exe to install this version of Keil µVision.

•EWARM-CD-6502.exe to install this version of the

IAR Embedded Workbench. The IAR Embedded

Workbench requires registering on the IAR website

to obtain a free license key.

The Segger J-link software is selected by default in the

installation menu. It is advised to leave it selected. This

automatically installs the J-Link serial port driver (keep

the default settings that appear in the next Segger messages

windows).

However, if you decide to unselect the Segger J-Link

Software install, and install it at a later stage, you will, at

that time, need to run the Setup_JLinkARM_V459d.exe

located under ADuCMxxxV1.3\Segger. Then, select

Install J-Link Serial Port Driver as shown in Figure 6.

Alternatively, you can run JLinkCDCInstaller_V1.2b.exe

located under ADuCMxxxV1.3\Segger.

Figure 6. Installing Link Software

Although the development system, the IAR Embedded

Workbench®, and the Keil™ software can be installed onto any

hard drive and into any directory, for the purposes of simplicity,

this user guide assumes it is installed at the default location

of C:\ADuCMxxxV1.3, C:\Program Files and C:\keil. In

addition, the Keil tools are automatically installed under an

ARM directory and are fully compatible with µVision3 or tools

for 8051.

If you choose the IAR tools, these will be installed

by default into \Program Files\IAR Systems\Embedded

Workbench 6.5.

10952-005

10952-006

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Getting Started Guide ADuCM360/ADuCM361

Rev. A | Page 5 of 16

PROGRAMS INSTALLED

The software described in this section has now been copied or

installed.

CM3WSD.exe

The folder \ADuCMxxxV1.3\Software Tools\CM3WSD

provides an executable called CM3WSD.exe. This software

accepts a hex file and allows it to be downloaded via the USB

interface to the ADuCM360 device on your evaluation board.

You may want to add a shortcut link for this executable to your

desktop.

elves.exe

The \ADuCMxxxV1.3\Software Tools\Elves folder contains

the elves.exe files. These files are useful tools that accompany

the software function libraries in

\ADuCMxxxV1.3\Code\ADuCM360\common. Again, no

installation is required here, but you may want to add a shortcut

link for this executable to your desktop.

Driver

The J-Link OB emulator requires a driver, which is installed

automatically when the Segger J-Link Software is selected (see

Step 3 of the Software Installation Instructions section). At this

point, check that the driver is installed correctly.

Plug in the emulator and check the device manager (see

Figure 7).

Check that it appears in the Windows Device Manager in both

the communications port and the USB controllers lists.

Figure 7. Device Manager

The J-Link OB emulator drivers JLinkCDCInstaller_V1.2b.exe

can be installed from the ADuCMxxxV1.3\Segger folder, if

J-Link does not appear in the device manager as shown in

Figure 7.

Note that the drivers for J-Link Lite and interface boards

previously shipped in the ADuCM360 development system are

available online.

10952-007

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADuCM360/ADuCM361 Getting Started Guide

Rev. A | Page 6 of 16

KEIL µVISION4 INTEGRATED DEVELOPMENT ENVIRONMENT

INTRODUCTION

The µVision4 Integrated Development Environment (IDE)

integrates all the tools necessary to edit, assemble, and

debug code. The ADuCM360 development system supports

nonintrusive emulation limited to 32 kB code. This section

describes the project setup steps in order to download and

debug code on an ADuCM360 evaluation system. Analog

Devices recommends using the J-Link debugger driver.

QUICK START STEPS

From the Start menu, choose All Programs>Keil µVision4.

This loads the µVision4 IDE. The µVision4 executable is

located at C:\Keil\UV4\Uv4.exe.

1. To open one of the prepared Keil µVision example projects

in µVision, select Project>Open Project.

Figure 8. Open an Example Project

2. In the folder

\ADuCMxxxV1.3\Code\ADuCM360\examples\

RTD_Demo, select the file RTD_Demo.uvproj. This

opens the RTD example project.

Figure 9. RTD Example Project

To compile and build all files, select the Build All icon

Once the build has completed, the code shown in Figure 10

appears.

Figure 10. Build Output

3. To download the code to the EVA L-ADuCM360MKZ

board and begin a debug session, connect the J-Link OB

emulator to the ADuCM360 mini-board and to your PC

using the provided USB cable.

4. In μVision, click the Start/Stop Debug session icon

or press Ctrl + F5 to start a debugging session.

5. Click OK when the window shown in Figure 11 appears.

Figure 11. Evaluation Mode

6. Begin debugging your source code.

Figure 12. Debug Source Code

10952-008

10952-009

10952-010

10952-011

10952-012

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Getting Started Guide ADuCM360/ADuCM361

Rev. A | Page 7 of 16

EXTRA OPTIONAL DETAILS ON µVISION

This section provides a more detailed explanation of the setup

described in the Quick Start Steps section. Some users may

prefer to setup via the Quick Start Steps section.

Toolbars

Under the View menu, two toolbars are available.

•File toolbar

•Build toolbar/Debug toolbar

The File toolbar is always available. The Build toolbar is active

only when the IDE is in edit/compile mode. The Debug toolbar

is active only in download/debug mode.

Starting a Project

1. From the Project menu, select New µVision Project.

Figure 13. Project Menu

2. Create a new folder (ADIdemo). To do so, go to

C:\ADuCMxxxV1.3\Code\ADuCM360\examples\

ADIdemo and enter Demo as the project name. If asked to

Select a CPU Data Base File, select the Generic CPU Data

Base.

Figure 14. Select a CPU Data Base File

3. Select the ADuCM360 in the Generic CPU Data Base.

Figure 15. Select ADuCM360

4. Select No to the question that appears (see Figure 16). This

indicates you are not automatically including the start-up

file startup_ADuCM360.s to your project.

Figure 16. µVision Startup Question

Note that it is possible to change the compiler by selecting

the File Extensions, Books and Environment folder

extension.

Figure 17. File Extensions, Books and Environment

5. For this demo, select Use RealView under the

Folders/Extensions tab.

Figure 18. Components, Environment and Books

6. In the project window, right-click on Target1 and select

Option for Target1 to configure the settings for this

project. By default, µVision4 uses the RealView compiler.

•Select the Target tab.

•Ensure the IROM1 and IRAM1 Start and Size fields

are filled as shown in Figure 19.

•Ensure that the Use MicroLIB option is enabled.

10952-013

10952-014

10952-015

10952-016

10952-017

10952-018

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

ADuCM360/ADuCM361 Getting Started Guide

Rev. A | Page 8 of 16

Figure 19. Options for Target

7. Select the Linker tab and then select Use Memory Layout

from Target Dialog.

Figure 20. Linker Options

8. In the Output tab, select Create HEX File. The hex file can

be used by the Windows Serial Downloader (CM3WSD).

Then, select OK.

Figure 21. Output Tab

9. Connect the emulator to the ADuCM360 mini-board and

to your PC’s USB port using a USB cable.

Note that an LED on the J-Link OB emulator blinks several

times before staying on, indicating that the emulator is

communicating correctly with the PC.

Configuring the J-Link Debugger Driver

1. In the project window, right-click on Target1 and select

Option for Target1 to configure the settings of this

project.

2. In the Debug tab, select Use:and then select J-LINK/

J-Trace Cortex.

Figure 22. Choose a Debugger

3. Select Run to main().

4. Select Settings in Figure 22 and then configure as shown in

Figure 23.

Figure 23. Target Driver Setup

5. Select OK.

6. Under Utilities, select Use Target Driver for Flash

Programming. Then, choose J-LINK/J-Trace Cortex and

select the option Update Target before Debugging.

10952-019

10952-020

10952-021

10952-022

10952-023

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Getting Started Guide ADuCM360/ADuCM361

Rev. A | Page 9 of 16

Figure 24. Continuing with Target Driver Setup

7. Select Settings to display the dialog box shown in

Figure 25.

Figure 25. J-Link/J-Trace Cortex Setup

8. Select Add to display the window shown in Figure 26.

Select the driver for the generic that you are evaluating.

For this example, use ADuCM360 128kB Flash and then

select Add.

Figure 26. Add Flash Programming Algorithm

9. Select OK when the window shown in Figure 27 appears.

Figure 27. Finishing Target Driver Setup

10. In the C/C++ tab, add the include path as shown in

Figure 28.

11. Select OK. All the options should be properly configured

to compile, assemble, link, download, and debug using

J-Link Lite.

10952-024

10952-025

10952-026

10952-027

ADuCM360/ADuCM361 Getting Started Guide

Rev. A | Page 10 of 16

Figure 28. Options for Target Setup

Adding Project Files

All the files relative to the project are in the folder

\ADuCMxxxV1.3\Code\ADuCM360\examples\Adc.

Copy the file

\ADuCMxxxV1.3\Code\ADuCM360\examples\Adc

\ADCMeter.c into the new directory C:\ \ADuCMxxxV1.3\

Code\ADuCM360\examples\ADIdemo.

1. To add the files to the project, right-click on the Source

Group folder in the Project window and select Add Files

to Group.

Figure 29. Adding Files to the Project

Note that under Project>Manage, the option

Components, Environment, Books can be used to rename

the target and add the file relative to your project.

Figure 30. Renaming the Target

2. Add all the files listed in Figure 31 from the directory

\ADuCMxxxV1.3\Code\ADuCM360\common. The

Startup file is located in the RealView folder.

Figure 31. Project Files

3. Double-click on the file name (ADCMeter.c) in the

Project window to open the source file.

Assembling/Compiling Code

To compile/link ADCMeter.c, click on the (translate current

file) icon in the toolbar. The file should compile correctly and

the information shown in Figure 32 should appear in the Build

Output window. If there are errors in your source code, these

appear in the status window. To identify the line of code that

corresponds to the error, double-click on the error in the Build

Output window and an arrow highlights the line of code in

error.

Before the code can be downloaded to the ADuCM360,

the entire project must be built. This is done by clicking on the

(rebuild all target files) icon on the toolbar. It will also

create a demo.elf file used by the debugger.

Figure 32. Build Output

10952-028

10952-029

10952-030

10952-031

10952-032

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Analog Devices Mikrocontroller Handbücher

Analog Devices

Analog Devices ADF7030-1 EZ-KIT Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADUCM10QSPZ Bedienungsanleitung

Analog Devices

Analog Devices AN-951 Montage- und Bedienungsanleitung

Analog Devices

Analog Devices EV1HMC8362LP6G Bedienungsanleitung

Analog Devices

Analog Devices ADuCM4050 EZ-KIT Bedienungsanleitung

Analog Devices

Analog Devices ADRV9001 Bedienungsanleitung

Analog Devices

Analog Devices MicroConverter ADuC706x Technisches Datenblatt

Analog Devices

Analog Devices EV-AD7284TMSDZ Bedienungsanleitung

Analog Devices

Analog Devices Linear ADI Power DC3091 Bedienungsanleitung

Analog Devices

Analog Devices ADuCM355 Kurzanleitung

Analog Devices

Analog Devices DC1840C Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices Linear Technology ADI Power DC3159A Kurzanleitung zur Einrichtung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung