Analog Devices DC336 Bedienungsanleitung

Inhaltsverzeichnis

Andere Analog Devices Hauptplatine Handbücher

Analog Devices

Analog Devices EVAL-AD7276SDZ Bedienungsanleitung

Analog Devices

Analog Devices EZ-Extender ADSP-CM408 Series Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD2437B1MZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADP5020 Bedienungsanleitung

Analog Devices

Analog Devices AD9516 Bedienungsanleitung

Analog Devices

Analog Devices UG-547 Bedienungsanleitung

Analog Devices

Analog Devices EV-ADF5355SD1Z Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADGM1144SDZ Bedienungsanleitung

Analog Devices

Analog Devices ADSP-SC589 EZ-Board Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADHV4702-1CPZ Bedienungsanleitung

Analog Devices

Analog Devices EV-PRG-MW1001ARDZ Bedienungsanleitung

Analog Devices

Analog Devices MAX16165 Bedienungsanleitung

Analog Devices

Analog Devices DC2515B Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices EVAL-AD2437A1NZ Bedienungsanleitung

Analog Devices

Analog Devices AD9864 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADGS1408SDZ Bedienungsanleitung

Analog Devices

Analog Devices ADXRS800 Bedienungsanleitung

Analog Devices

Analog Devices ADP1650 Bedienungsanleitung

Analog Devices

Analog Devices MAX30001G Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD5592RSDZ Bedienungsanleitung

Analog Devices

Analog Devices ADSP-BF518F EZ-Board Bedienungsanleitung

Analog Devices

Analog Devices AD9144-FMC-EBZ Bedienungsanleitung

Analog Devices

Analog Devices EZ-KIT Lite ADSP-BF537 Bedienungsanleitung

Analog Devices

Analog Devices ADuCM350 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

DC336 QUICK START GUIDE

Description

Demonstration circuit DC336 is a white LED driver using the LTC3200 low noise, constant

frequency, inductorless DC/DC converter. The circuit is designed to drive five white LEDs from

a single Li-Ion cell. The LTC3200’s 2MHz constant switching frequency and internal switching

control result in extremely low input and output ripple and small circuit size (23mm2). DC336 is

specifically targeted for white LED backlight applications in cellular phones and small handheld

devices, such as PDAs, where noise and circuit size are critical. The input ripple and output

ripple performance can be improved by using 4.7µF, X7R ceramic capacitors at the input and

output (refer to the LTC3200 data sheet). Gerber files for this circuit board are available. Call the

LTC factory.

Quick Start

DC336 is easy to set up to evaluate the LTC3200 low noise, LED driver circuit. Refer to Figure 1

for equipment setup and follow the procedure outlined below:

1. Before turning on the power supply, connect a 3.3V, 500mA bench supply to the VIN and GND

terminals.

2. Turn on the input power supply and observe that the white LEDs light up. The output voltage

should measure 5V (typical) with 3V–4.2V input voltage.

3. Connect the JP1 jumper to the “off” position to turn off the LTC3200. Returning the jumper to

the “on” position will turn on the LTC3200.

+

–

+

–

VIN

GND

SHDN

VOUT

GND

JP1 ] OFF

] ON

LTC3200ES6

White LED Driver for Cellular Phone

Demo Circuit DC336A

POWER

SUPPLY

Figure 1. DC336A Test and Measurement Setup

4. When measuring the input / output voltage ripple, care must be taken to avoid a long ground

return for the oscilloscope probe. After removing the grabber and outer plastic sleeve from the

scope probe, measure the input voltage ripple by touching the probe between VIN and GND

and measure the output voltage ripple by touching the probe between VOUT and GND as

shown in Figure 2.

VIN

GND

VOUT

GND

MEASURING

V

IN

RIPPLE

MEASURING

V

OUT

RIPPLE

TEKTRONIX

TDS 640A

OSCILLOSCOPE

PROBE

Figure 2. Proper Noise Measurement Technique