Analog Devices DC353A Bedienungsanleitung

DC353A DEMO BOARD QUICK START GUIDE

DESCRIPTION

Demonstration circuit DC353A demonstrates the capabilities of the LTC1928-5 doubler

charge pump and linear regulator. The board contains the following:

• LTC1928-5 doubler charge pump with low noise linear regulator.

• 4.7µF ceramic capacitor on VOUT

• 4.7µF ceramic capacitor on CPO

• 4.7µF ceramic capacitor on VIN

• 0.47µF ceramic capacitor between CP and CN/SHDNB

• N-channel FET type 2N7002 to supply an open-drain pulldown during shutdown

• 50Ωtermination resistor at the gate of the 2N7002 FET

• A 100Ωcurrent-limit resistor between the drain of the 2N7002 FET and the

CN/SHDNB pin

The LTC1928-5 generates a low noise regulated 5V output from a DC input supply

voltage connected to the VIN terminal. The DC supply voltage range is 2.7V to 4.4V. The

small SOT-23 package and small ceramic capacitors minimize board space requirements.

A power supply connected to VIN is the only requirement for basic operation of the demo

board. The termination resistor at the gate of the 2N7002 keeps this FET off and the

LTC1928-5 out of shutdown (enabled).

EXTERNAL CONNECTIONS

Refer to Figure 1 for proper power supply and test equipment setup.

Connect a 2.7V to 4.4V DC voltage supply to the VIN terminal.

Connect the DC supply ground to the GND terminal.

Connect a pulse generator switching from 0V to 5V to the SHDN terminal (optional).

The part will be enabled when the pulse generator signal is low and disabled when the

pulse generator signal is high. If the pulse generator is not connected the part will be

enabled.

Connect the load between the VOUT and GND terminals directly at the board if noise

measurements are being performed.sdfsdfasdf

+

–

+

–

–

–

–

+

+

+

+

–

+–

LOAD

GND

VIN

VOUT SHDN

LTC1928S6-5

DEMO CIRCUIT 353A

LOW NOISE BOOST

DC/DC CONVERTER

Figure 1. DC353 Test and Measurement Setup

OPERATING MODES

DC353A is designed to demonstrate the low noise performance of the LTC1928-5 as well

as its shutdown and current-drive capabilities.

Enable Mode

The device is enabled when the SHDN signal is at 0V. VOUT will be between 4.9V and

5.1V. Noise measurements can be performed as outlined in the LTC1928-5 data sheet.

Loads should be applied between the VOUT and the GND terminals on the demo board to

avoid ground loops. Ground loops could result in excessive noise generation. A variable

resistor or current source can be applied to the VOUT terminal to characterize the output

current drive capabilities.

Shutdown Mode

The 2N7002 FET is required to place the LTC1928-5 in shutdown. Shutdown is achieved

by applying five volts to the SHDN terminal which turns the 2N7002 on. The 50Ω

termination resistor at the SHDN terminal minimizes ringing when the user controls

shutdown using a pulse generator. The pulse generator can be set to switch between 0V

and 5V. The enable and disable characteristics can be determined by obserVINg the

output voltage at VOUT and the input current at VIN. The pulse generator frequency will be

in the 100s of Hertz range. When the part is disabled, VOUT will be discharged to ground

via an internal pull down transistor. The data sheet contains example waveforms showing

the on and off characteristics of VOUT. In actual applications, the 2N7002 can be replaced

with an open-drain transistor associated, for example, with a system controller.

Inhaltsverzeichnis

Andere Analog Devices Hauptplatine Handbücher

Analog Devices

Analog Devices EV-ADF5355SD1Z Bedienungsanleitung

Analog Devices

Analog Devices ADSP-21161N Bedienungsanleitung

Analog Devices

Analog Devices UG-486 Bedienungsanleitung

Analog Devices

Analog Devices DC2685B-KIT Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices ADIS1650 Series Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD7766EDZ Bedienungsanleitung

Analog Devices

Analog Devices AD9152-FMC-EBZ Bedienungsanleitung

Analog Devices

Analog Devices ADP5062 Bedienungsanleitung

Analog Devices

Analog Devices UG-185 Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADPD1081Z-PPG Bedienungsanleitung

Analog Devices

Analog Devices EVAL-RS485HDEBZ Bedienungsanleitung

Analog Devices

Analog Devices DC2958A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices EV-21569-SOM Bedienungsanleitung

Analog Devices

Analog Devices EVAL-AD5753SDZ Bedienungsanleitung

Analog Devices

Analog Devices AD8333-EVALZ Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADV7612-7511 Bedienungsanleitung

Analog Devices

Analog Devices DC2652A-A Bedienungsanleitung

Analog Devices

Analog Devices EVAL-FLTR-DF-1RZ Montage- und Bedienungsanleitung

Analog Devices

Analog Devices EVAL-ADPD188BIZ-SK Bedienungsanleitung

Analog Devices

Analog Devices MAX17553C EV Kit A Bedienungsanleitung

Analog Devices

Analog Devices Linear Technology DC2472A Kurzanleitung zur Einrichtung

Analog Devices

Analog Devices ADZS-AD2428MINI Bedienungsanleitung

Analog Devices

Analog Devices EVAL-SSM6515 Bedienungsanleitung

Analog Devices

Analog Devices SSM2529 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung