Andersen E Series Gebrauchs- und Pflegehandbuch
9069265 BA-0 0 Revised 01/19/18
Window Blind Replacement
for Andersen®E-Series Casement Windows with System 3 Blinds
Use caution when working at elevated heights and around unit openings.
Follow manufacturers’ instructions for ladders and/or scaffolding. Failure
to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always
wear safety glasses. Failure to do so may result in injury and/or
product damage.
Parts Included
(1) Replacement Blind
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.andersenwindows.com.
Please leave this guide with building owner.
▶Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.
▶Check with your local building code ofcial to identify and conrm compliance with local building code requirements.
Tools Needed
∙Safety Glasses
∙Phillips Screwdriver
∙Flat Blade Screwdriver
∙Needle-nose Pliers
∙.050" Hex Key
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2018 Andersen Corporation. All rights reserved.
Replacement Blind
2
9069265
5
Interior
6
Interior
2
Interior
3
Interior
4
Interior
▶Proceed to step 2 for windows WITH insect screens.
▶Proceed to step 5 for windows WITHOUT insect screens.
Lift up and out on lift bar at bottom of insect screen to unseat
insect screen from window frame.
Unlock and open sash.
Feed plastic tassels of blind cords one at a time through grommet in
insect screen frame.
Remove insect screen from window opening. Close and lock window. Remove blind panel screws with phillips screwdriver and save for reuse.
Unwrap lift blind cord from cord retainer clip and slowly lower the
blind.
1
Interior
Plastic Tassels
Grommet
Blind Panel
Screw
Window
Frame
Blind
Panel
Insect
Screen
Window Frame
Insect Screen
Cord Retainer Clip
Blind Cords
Lift Bar
Phillips
Screwdriver
Window
Frame
3
9069265
8
Interior
9
Interior
7
Interior
11
Interior
10
Interior
Lift blind panel out of window sash. Lay on a clean at surface with the
interior surface face down. Position panel on table so that the control
knob is hanging over table edge. Failure to do so could result in panel
damage.
Disconnect the tilt control cable from the D-rod located along the top
side of the panel using .050" hex key.
Insert at blade screwdriver between blind panel frame and blind head
rail and pry. Repeat at locations of mounting clips as necessary to
release blind assembly.
Remove blind panel frame cord from blind panel frame.
Feed plastic tassels through the blind cord hole one at a time. Dispose
of blind properly.
Insert tilt control knob cable and cords from new blind through the holes
in blind panel frame.
12
Interior
The grommet is split to allow it to
be removed from the cords.
Control knob hanging over
edge of table
Tilt Control Cable
D-rod
.050" Hex Key
Flat Blade Screwdriver
Blind Panel Frame
Blind Head Rail
Blind Panel
Frame Grommet
Plastic Tassels
Blind Cord Hole Blind Cords
Blind Panel Frame
Tilt Control Knob Cable
4
9069265
13
Interior
14
Interior
15
Interior
Insert blind cords and re-insert blind panel grommet into hole in blind
panel frame. Position the split in blind panel frame grommet so that
it will face toward sash when installed. Failure to do so will result in
damage to the blind cords.
Push the blind assembly toward top of blind panel and snap into
mounting clips.
Reconnect tilt control knob cable to D-rod. Tighten hex screw using
.050" hex key.
Lift blind panel into window opening. Set bottom of panel onto window
sash and tip into place. Fasten using saved screws.
17
Interior
Unlock and open window. Position insect screen near window opening.
▶Proceed to step 17 for windows WITH insect screens.
▶Proceed to step 21 for windows WITHOUT insect screens.
16
Interior
Feed plastic tassels of blind cords one at a time through grommet in
insect screen frame.
18
Interior
Blind Panel
Frame
Blind
Panel Frame
Grommet
Tilt Control Knob
Cable
.050" Hex Key
D-rod
Window
Frame
Insect
Screen Plastic Tassels
Grommet
Window Frame
Blind Panel
Phillips Screwdriver
Split in cord pass through grommet must be
positioned to face toward sash. Failure to
do so will result in damage to cords.
5
9069265
▶System 3 blind replacement is complete.
Lift up and toward sash on lift bar at bottom of insect screen to seat
insect screen into window frame.
Close and lock window.
19
Interior
21
Interior
Check for proper operation. Secure blind cords to cord retainer clip.
20
Interior
Cord Retainer Clip
Blind Cords
Andere Handbücher für E Series
2
Dieses Handbuch passt für folgende Modelle
1
Andere Andersen Jalousie Handbücher
