Anritsu MD1230A-06 Bedienungsanleitung
Document No.: M-W2122AE-8.0
ANRITSU CORPORATION
Tcl Interface
Operation Manual
Eighth Edition
•This is an operation manual of MD1230A-06,
MD1230B-06, MD1231A-06, MD1231A1-06,
MX123001A-06.
•Read this manual before using the equipment.
•To ensure that the equipment is used safely, read
the “For Safety” in the Operation Manual for each
main unit first.
•Keep this manual with the equipment.
ii
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following
safety symbols to indicate safety-related information. Insure that you clearly understand the meanings of the sym-
bols BEFORE using the equipment. Some or all of the following five symbols may not be used on all Anritsu
equipment. In addition, there may be other labels attached to products which are not shown in the diagrams in this
manual.
Symbols used in manual
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
This indicates a hazardous procedure or danger that could result in light-to-severe
injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual
The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. Insure that you clearly understand the meanings of the symbols
and take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated sym-
bolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is indicat-
ed symbolically in or near the circle.
This indicates warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
Tcl Interface
Operation Manual
1 February 2003 (First Edition)
25 November 2005 (Eighth Edition)
Copyright © 2003-2005, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
DANGER
WARNING
CAUTION
iii
Equipment Certificate
Anritsu guarantees that this equipment was inspected at shipment and
meets the published specifications.
Anritsu Warranty
•During the warranty period, Anritsu will repair or exchange this soft-
ware free-of-charge at the company’s own discretion if it proves defec-
tive when used as described in the operation manual.
•The warranty period is 1 year from the purchase date.
•The warranty period after repair or exchange will remain 1 year from
the original purchase date, or 30 days from the date of repair or ex-
change, depending on whichever is longer.
•This warranty does not cover damage to this software caused by Acts
of God, natural disasters, and misuse or mishandling by the customer.
In addition, this warranty is valid only for the original equipment pur-
chaser. It is not transferable if the equipment is resold.
Anritsu Corporation will not accept liability for equipment faults due to
unforeseen and unusual circumstances, nor for faults due to mishandling
by the customer.
Anritsu Corporation Contact
In the event that this equipment malfunctions, contact an Anritsu Service
and Sales office. Contact information can be found on the last page of
the printed version of this manual, and is available in a separate file on
the CD version.
iv
Notes On Export Management
This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from you
r
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals are
needed to be broken/shredded so as not to be unlawfully used for military
purpose.
v
Software License Agreement
Please read this Software License Agreement before using the accom-
panying software program (hereafter this software).
You are authorized to use this software only if you agree to all the terms
of this License.
By opening the sealed package containing this software, you are agreeing
to be bound by the terms of this License.
If you do not agree to these terms, return the unopened software package
to Anritsu Corporation (hereafter Anritsu).
1. License
(1) This License gives you the right to use this software on one comput-
er system.
(2) To use this software on one computer system, this License allows
you to make one copy of this software on the storage device of your
computer system.
(3) You must obtain a site license to use this software on more than one
computer system even if such computer systems are not operating
simultaneously.
2. Copyright
(1) Although you are licensed to use this software, Anritsu retains the
copyright.
(2) Although you have purchased this software, rights other than those
specified in this License are not transferred to you.
(3) You may not print, copy, modify, create derivative works, incorpo-
rate in other software programs, decompile or disassemble this
software in whole or in part, without obtaining prior written per-
mission from Anritsu.
3. Copying
Notwithstanding item (3) of section 2 above, you may make one copy of
this software for backup purposes only. In this case, you may only use
either the original or the backup copy of this software.
4. Termination
(1) Anritsu will deem this License to be automatically terminated if you
fail to comply with any provision of this License. Upon termination,
you will lose all rights to this software.
(2) Either party (Anritsu or yourself) to this Software License Agree-
ment may terminate this Agreement by giving 1 months notice in
writing to the other party.
(3) Upon termination of this License for any reason, you must either
immediately destroy this software and related documentation, or re-
turn it to Anritsu.
vi
CE Conformity marking
Anritsu affixes the CE Conformity marking on the following product (s) in
accordance with the Council Directive 93/68/EEC to indicate that they
conform to the EMC and LVD directive of the European Union (EU).
CE marking
1. Product Model
Option: MD1230A-06 Tcl interface,
MD1230B-06 Tcl interface,
MD1231A-06 Tcl interface,
MD1231A1-06 Tcl interface
2. Applied Directive and Standards
When the above options are installed in the main frame shown below,
the applied directive and standards of these options are conformed to
those of the main frame.
Main frame: MD1230A/B Data Quality Analyzer,
MD1231A/A1 IP Network Analyzer
PS: About main frame
The kind of main frame (a measuring apparatus) will be to increase.
Please, contact us about the newest information of the main frame.
vii
C-tick Conformity marking
Anritsu affixes the C-tick marking on the following product (s) in accor-
dance with the regulation to indicate that they conform to the EMC
framework of Australia/New Zealand.
C-tick marking
1. Product Model
Option: MD1230A-06 Tcl interface,
MD1230B-06 Tcl interface,
MD1231A-06 Tcl interface,
MD1231A1-06 Tcl interface
2. Applied Directive and Standards
When the above options are installed in the main frame shown below,
the applied directive and standards of these options are conformed to
those of the main frame.
Main frame: MD1230A/B Data Quality Analyzer,
MD1231A/A1 IP Network Analyzer
PS: About main frame
The kind of main frame (a measuring apparatus) will be to increase.
Please, contact us about the newest information of the main frame.
viii
I
About This Manual
MD1230 family operation manual consists of the main unit, control soft-
ware, modules, remote control and options shown below.
Note:
MD1230 family is the generic name of MD1230A/B Data Quality
Analyzer, MD1231A/A1 IP Network Analyzer and MT7407A Multislot
Chassis.
Explains MD1230A/B basic operations.
MD1230 family
Operation Manual
configuration
Explains the usage of software that controls the
main frame of the MD1230 family.
MX123001A Data Quality Analyzer
Control Software Operation Manual
Explains basic operations for each SDH/SONET
module.
Explains basic operations for each Ethernet
module.
Ethernet Module
Operation Manual
Remote Control
Operation Manual
Explains the remote control via RS-232C, GPIB
and Ethernet Interfaces.
shows this document.
Explains basic operations for each SDH/SONET
module.
MU120119A OC-3/12 STM-1/4 Module (1310 nm)
MU120120A OC-3 STM-1 Module (1310 nm)
Operation Manual
MU120103A/B 2.5G (1.31) Module
MU120104A/B 2.5G (1.55) Module
MU120105A 10G (1.31) Module
MU120106A 10G (1.55) Module
Operation Manual
MD1230A/B Data Quality Analyzer
Operation Manual
Explains MD1231A/A1 basic operations.
MD1231A/
A
1 IP Network Analyzer
Operation Manual
Explains MT7407A basic operations.
MT7407A Multislot Chassis
Operation Manual
II
Tcl Interface
Operation Manual
Explains basic operation for Tcl Interface.
Expert Analysis Module
Operation Manual
Explains basic operation for the Expert Analysis
Module.
Decode Module
Operation Manual
Explains basic operations for Decode Module.
A
pplication Traffic Monitor
Operation Manual
Explains operation for the software that monitors
traffics on Ethernet.
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Anritsu Aufnahmegeräte Handbücher
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
