ANTAIRA LNP-0800G-M12-67-24 Bedienungsanleitung

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

LNP-0800G-M12-67-24

8-Port Industrial M12 IP67 Waterproof Gigabit PoE+ Ethernet Switch,

w/8*10/100/1000Tx (30W/Port) M12 Connector (X-Coded), 24~55VDC;

-10° to 60°C

Version 1.0

(September 2018)

User Manual

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

This document contains information, which is protected by copyright. Reproduction, adaptation, or translation

without prior permission is prohibited, except as allowed under the copyright laws.

Trademark Information

Antaira is a registered trademark of Antaira Technologies, LLC., Microsoft Windows and the Windows logo are

the trademarks of Microsoft Corp. All other brand and product names are trademarks or registered trademarks of

their respective owners.

Disclaimer

Antaira Technologies, LLC. provides this manual without warranty of any kind, expressed or implied, including but

not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,

LLC. may make improvements and/or changes to the product and/or specifications of the product described in

this manual, without prior notice. Antaira Technologies, LLC. will not be liable for any technical inaccuracies or

typographical errors found in this guide. Changes are periodically made to the information contained herein and

will be incorporated into later versions of the manual. The information contained is subject to change without prior

notice.

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

iii

FCC Notice

This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy. It may cause

harmful interference to radio communications if the equipment is not installed and used in accordance with the

instructions. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's

authority to operate the equipment.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause radio interference in which case the

user may be required to take adequate measures.

Industrial Ethernet Switches

User Manual

This manual supports the following models:

•LNP-0800G-M12-67-24

Please check our website (www.antaira.com) for any updated manual or contact us by e-mail

([email protected]).

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

Table of Contents

1.Overview....................................................................... 1

1.1 Key Features...................................................... 1

1.2 Package Contents.............................................. 1

1.3 Safety Precaution............................................... 1

2.Hardware Description ................................................. 3

2.1 Physical Dimensions.......................................... 3

2.2 Front Panel ........................................................ 4

2.3 Top View............................................................ 4

2.4 LED Indicators ................................................... 5

2.5 Grounding .......................................................... 6

2.6 Ethernet Ports.................................................... 6

2.7 Power Inputs...................................................... 7

2.8 Relay Contact and Digital Input ......................... 8

2.9 Prioritization of PoE Ports................................ 10

2.10 Bypass Function ............................................ 10

2.11 Prioritization of Packets ................................. 11

3.Mounting Installation ................................................ 12

3.1 Wall Mounting .................................................. 12

4. Hardware Installation................................................ 14

4.1 Installation Steps.............................................. 14

4.2 Maintenance and Service ................................ 15

5. Network Application ................................................. 16

6. Trouble Shooting ...................................................... 17

7. Technical Specifications.......................................... 18

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

1.Overview

Antaira Technologies’ LNP-0800G-M12-67-24 is an 8-port 10/100/1000Tx M12 IP67 PoE+ industrial

Ethernet switch that meets the high-reliability requirements demanded by industrial applications. Its M12

connectors ensure a tight and robust connection and it guarantees reliable operation on applications that

are subject to high vibration and shock in dust, liquid, or gas laden environments. Being able to operate

under the temperature range from -10°C to 60°C, the LNP-0800G-M12-67-24 can be installed in almost

any harsh environment.

1.1 Key Features

◼System Interface/Performance

•All copper ports support auto MDI/MDI-X function

•Embedded 8*10/100/1000Tx with IEEE 802.3at compliant ports (30W/port)

•Store-and-forward switching architecture

•8K MAC Address Table

•Supports 12.2Kbytes Jumbo Frame

•448Kbits memory buffer

◼Power Input

•Redundant power DC 24-55V through M12 4-Pin T-Coded male connector

•Max. current 8.8A

•Max. PoE output: 200Watts

•Relay Contact: 24VDC, 1A resistive, through M12 5-Pin A-Coded female connector

◼Operating Temperature

•Standard operating temperature model: -10°C ~ 60°C

◼Case/Installation

•Aluminum case

•IP67 protection

•Installation in a Pollution Degree 2 industrial environment

•Wall mount design

1.2 Package Contents

•1 –Quick Installation Guide

•1 –LNP-0800G-M12-67-24

•1 –Set of 10*M12 protective caps

1.3 Safety Precaution

Attention

If the DC voltage is supplied by an external circuit, please use a protection device on the power supply

input. Supply by a UL listed industrial use power. The industrial Ethernet switch’s hardware specs, ports,

cabling information, and wiring installation will be described within this user manual.

Warning Labels

The caution label means that you should check the certain information in the user manual when working

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

with the device. (Shown in Figure 1)

Figure 1: Caution Label

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

2. Hardware Description

2.1 Physical Dimensions

Figure 2.1, below, shows the physical dimensions of Antaira Technologies’ LNP-0800G-M12-67-24:

(W x H x D) is 253.6mm x 122mm x 116.1mm

Figure 2.1

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

2.2 Front Panel

The front panel of the LNP-0800G-M12-67-24 can be seen below (Figure 2.2).

1. Power 1 LED

2. Power 2 LED

3. Fault LED

4. PoE Load LED

5. 10/100/1000Mbps Link/Act LED

6. PoE Output LED

7. Screw Holes for Wall Mounting

8. Grounding Screw

9. Power Input Port: M12 4-Pin T-Coded Male Connector

10. Product Label

11. 10/100/1000Base-T(X) Ethernet Port: From Port G1 to G8 with M12 8-Pin X-Coded Female

Connector

2.3 Top View

Figure 2.3, below, shows the bottom panel of the LNP-0800G-M12-67-24 that is equipped with 8 x

M12 X-Coded female connectors, 1 x M12 T-Coded male connector for dual DC power inputs (24-

55VDC), and 1 x M12 A-Coded female connector for relay contact/digital input.

Figure 2.2

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

2.4 LED Indicators

There are LED light indicators located on the front panel of the industrial Ethernet switch that

displays the power and network status. Each LED indicator has a different color and has its own

specific meaning, see below in Table 2.1.

LED

Color

Description

Green

Power input 1 is active

Off

Power input 1 is inactive

Green

Power input 2 is active

Off

Power input 2 is inactive

Fault

Red

There are three possible conditions that would make the

LED light up:

1. If the current PoE outputs of all connected PDs were

overloaded (>200 Watts)

2. If Power 1 or Power 2 was inactive

3. If the current PoE output of one or more PDs was

overloaded (>30Watts)

Off

Since the last reset of the fault LED, the PoE output of all

connected PDs has not over 200W and no PD has been

overloaded in this period and the power 1 & power 2 have not

failed

PoE Load

Off

The current PoE output of all connected PDs is ≤ 50%

Green

The current PoE output of all connected PDs is 51% ~ 70%

Blue

The current PoE output of all connected PDs is 71% ~ 90%

Red

The current PoE output of all connected PDs is 91% ~ 100%

Note: The Max. PoE output of this switch is 200Watts.

Figure 2.3

Antaira Technologies - Industrial Ethernet Switches

LNP-0800G-M12-67-24 User Manual V1.0

Port G1 to G8

L/A

Green

Connected to the network with 1000Mbps

Flashing

Networking is active

Off

Not connected to network

Amber

Connected to network with 10/100Mbps

Flashing

Networking is active

Off

Not connected to network

Port G1 to G8

PoE

Green

The current PoE output is enabled

Flashing

Overload occurred (>30 Watts) at the connected PD

Off

The current PoE output is disabled

NOTE: "P1/P2" is the abbreviation for "Power 1/Power 2", and “L/A” is for Link/Activity”.

2.5 Grounding

Grounding and wire routing help limit the effects of noise due to electromagnetic interference

(EMI). Run the ground connection from the ground screw to the grounding surface prior to

connecting devices. The grounding screw symbol is shown blow in Figure 2.4.

Figure 2.4

Caution: Using a shielded cable achieves better electromagnetic compatibility.

2.6 Ethernet Ports

M12 Interface (Auto MDI/MDIX)

◼Connection Format: M12 8-Pin X-Coded Female Connector

◼Transmission Rate: 10/100/1000 Mbit/s

Prepare the M12 8-Pin X-Coded Ethernet Port mating cable for Ethernet connection. The M12 X-

Coded Ethernet ports are auto-sensing for 10Base-T, 100Base-TX, or 1000Base-T devices

Table 2.1

Andere Handbücher für LNP-0800G-M12-67-24

Inhaltsverzeichnis

Andere ANTAIRA Schalten Handbücher

ANTAIRA

ANTAIRA LNX-0601G-SFP Bedienungsanleitung

ANTAIRA

ANTAIRA USB-HUB4K Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-C800 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-C602G-SFP-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0501-M-24 Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0601G-SFP-24-V2 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-1202G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1802G-M12-10G-SFP-67-110 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-C800 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-602N Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-2602G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-1802G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1002G-10G-SFP-24 Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-1202M-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-1202M-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-0800G Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0800-24 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-500AG Bedienungsanleitung

ANTAIRA

ANTAIRA LMP-2012G-SFP Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-C500-T-CC Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-1802G-M12-10G-SFP-67-110 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNP-0501 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LMX-0802 Series Bedienungsanleitung

ANTAIRA

ANTAIRA LNX-1802G-SFP Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch