Antec ISK 300-150 Bedienungsanleitung

ISK 300-150

USER’S MANUAL

TABLE OF CONTENTS

INTRODUCTION

1.1 Case Specifications.…..…………………………………………………………………………………..3

1.2 Diagram…………………………………………………………………….…………………………………. 3

1.3 Power Supply Specifications…………………………………………………………………………. 4

HARDWARE INSTALLATION GUIDE

2.1 Removing the Top Panel.……………………………………………………………………………….5

2.2 Removing the Drive Tray Assembly……….……………………………………………………… 5

2.3 Motherboard Installation..…………………………………………………………………………….5

2.4 Internal 2.5” Device Installation…………………………………………………………………….6

2.5 External Slim 5.25” Device Installation…………………………………………………………. 6

CONNECTING THE FRONT I/O PORTS

3.1 USB 2.0 Ports………………………………………………….……………………………………………. 7

3.2 eSATA Port…………………………………….………………………………………………………………7

3.3 AC’97 / HD Audio Ports……………………….…………………………………………………………7

3.4 Switch and LED Connectors……………………………………………………………………………8

3.5 Rewiring Motherboard Header Connections………………………………………………… 8

COOLING SYSTEM

4.1 TriCool™ Exhaust Fan…………………………………………………………………………………….9

ISK

300-150

SER

’

ANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible

that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s

simply an improvement. As of the date of publication, all features, descriptions, and illustrations in

this manual are correct.

Disclaimer

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive

instructions on installing the motherboard and peripherals, please refer to the user’s manuals that

come with those components.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend

taking the appropriate time and care when working with it. Avoid hurried or careless motions. Please

use reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the

motherboard manual for specific mounting instructions and troubleshooting. Before proceeding,

check the manual for your CPU cooler to find out if there are steps you must take before installing the

motherboard. While installing hardware, keep your case on a flat, stable surface.

1.1 CASE SPECIFICATIONS

Case Type

Mini-ITX Desktop

Color

Black

Dimensions

96mm (H) X 222mm (W) X 328mm (D)

3.8” (H) x 8.7” (W) x 12.9” (D)

Net Weight

5.5 lb / 2.5 kg

Cooling

1 x side 80mm TriCool™ fan

Drive Bays

3 drive bays:

-1 x External 5.25” slim drive bay

-2 x Internal 2.5” drive bays

Expansion Slots

1 x half-height slot

Motherboard Size

Mini-ITX

Front I/O Panel

2 x USB 2.0

1 x eSATA

AC’97 / HD Audio In and Out

Power Supply

FP-150-8 power supply

1.2 DIAGRAM

1. Side 80mm TriCool™ fan

2. External slim optical 5.25” drive bay

3. Internal 2 x 2.5” HDD bays

4. Half-height expansion slot

5. Motherboard mount –Mini-ITX

6. Front I/O panel

7. FP-150-8 power supply

Note: The ISK 300-150 includes a tool bag with Product Overview located inside of the case.

1.3 POWER SUPPLY SPECIFICATIONS

The ISK 300-150 is powered by an FP-150-8 power supply.

Input characteristics:

Input Voltage Range

Frequency Range

100VAC ~ 240VAC

47 Hz ~ 63 Hz

Output characteristics:

DC Output

+5V

+3.3V

+12V

-12V

+5Vsb

Max. Output

10A

0.2A

1.5A

+3.3V and +5V maximum combined output: 65W

Total Continuous Power: 150W

A variety of industrial-grade safety circuitry will help protect your computer: OVP (Over Voltage

Protection), SCP (Short Circuit Protection) and OCP (Over Current Protection). Sometimes the

PSU will “latch” into a protected shutdown state. This means that you will need to power off the

power supply and clear the fault before it will function again.

There are no user-replaceable fuses in the FP-150-8.

HARDWARE INSTALLATION GUIDE

2.1 REMOVING THE TOP PANEL

Place the case flat on an even, stable surface.

1. Remove the three thumbscrews from the rear of the

top panel.

2. Grip the top panel and slide it back several inches

until it stops.

3. Grip the panel from the sides and lift it up until it

pulls completely free of the main chassis.

Note: Do not use your fingernails to pry or lift the

panels.

2.2 REMOVING THE DRIVE TRAY ASSEMBLY

Remove the top panel as detailed in section 2.1.

1. Using a Phillips-head screwdriver, remove the three screws on the

top of the tray that attach it to the chassis.

2. Grip the tray in the middle and pull it a few inches toward the rear

of the case until it pulls loose.

3. Pull the drive tray assembly up and completely free of the chassis.

2.3 MOTHERBOARD INSTALLATION

Remove the top panel and remove the drive tray assembly as detailed in sections 2.1 and 2.2.

1. Lay the case down, with the open side facing up. The drive cages and

power supply should be visible.

2. Make sure you have the correct I/O panel for your motherboard. If

the panel provided with the case isn’t suitable, please contact your

motherboard manufacturer for the correct I/O panel. Install the I/O

panel at the rear of the case.

3. Align your motherboard with the motherboard standoff holes

located at the rear of the case.

4. Screw in your motherboard to the standoffs with the provided

Phillips-head screws.

Your motherboard is now installed.

2.4INTERNAL 2.5” DEVICE INSTALLATION

Remove the top panel as described in section 2.1. Included at the top

of the drive tray assembly is a HDD tray that can support up to two

2.5” devices.

1. On the right side of the drive tray assembly, remove the

thumbscrew holding the HDD tray to the rest of the device.

2. Slide the HDD tray back a centimeter so the locking hinges

unhook.

3. Pull the HDD tray away from the drive tray assembly.

4. Align your 2.5” device with the HDD tray. Invert the tray so the

lower screw holes are accessible, then secure the device to the

tray with the provided Phillips-head screws.

5. Reattach the HDD tray to the drive tray assembly and replace

the thumbscrew.

6. Connect the data and power connectors from the motherboard

and power supply to the device.

2.5 EXTERNAL SLIM OPTICAL DEVICE INSTALLATION

Remove the top panel and drive tray assembly as described in sections 2.1 and 2.2. There is one

externally accessible slim optical drive bay that is compatible with a slim optical drive.

1. While facing the front of the case, press on the upper right of

the front of the drive bay cover until it clicks, then release to

allow the cover to unhinge.

2. Remove the drive bay face plate by applying pressure to the

inside of the plate until it pops free of the bezel.

3. Install your slim optical drive in the drive bay assembly by

sliding it into position from the rear of the assembly. Secure the

device in place by attaching the included small screw on the

right-hand side of the tray.

4. Connect the data and power connectors from the motherboard

and power supply to the device.

5. Replace the drive tray assembly in the chassis.

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative Signal

Positive Signal

Ground

Key (No

Connection)

Empty

Signal

Names

(HDA)

Signal

Names

(AC’97)

MIC2

MIC In

AGND

GND

MIC2

MIC Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Key (no pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

ONNECTING THE

RONT

I/O

ORTS

3.1 USB 2.0

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the

motherboard manual to ensure that it matches the table below:

3.2 ESATA

You will find a SATA connector on a cable attached to the front ports. This internal SATA connector is

designed to connect to a standard SATA connector on your motherboard. This will allow high-speed

external hard disk enclosures such as the Antec MX-1 to run at the same speeds as internally installed

hard disks.

3.3 AC’97 /HD AUDIO PORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)

connector linked to the front panel of the case.

You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the

internal audio connectors from your motherboard or sound card and connect the corresponding audio

cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system

supports both standards, only use one connector.

1 2

9 10

3.4 POWER SWITCH /RESET SWITCH /HARD DISK DRIVE LED CONNECTORS

Connected to your front panel are LED and switch leads for power, reset, and

HDD LED activity. Attach these to the corresponding connectors on your

motherboard. Consult your motherboard user’s manual for specific pin

header locations. For LEDs, colored wires are positive ( + ). White or black

wires are negative ( –). If the LED does not light up when the system is

powered on, try reversing the connection. For more information on

connecting LEDs to your motherboard, see your motherboard user’s manual.

Note: Polarity (positive and negative) does not matter for switches.

3.5 REWIRING MOTHERBOARD HEADER CONNECTIONS

There may come a time when you need to reconfigure the pin-out of a motherboard header connector.

Examples could be for your USB header, audio input header, or some other front panel connector such

as the Power Button connector.

Before performing any work, please refer to your motherboard user’s manual or your motherboard

manufacturer's website to be sure of the pin-out needed for your connector. We strongly recommend

making a notated drawing before beginning work so that you can recover if your work gets disturbed.

1. Determine which wires you need to remove in order to rewire your

plug to match the USB pin-outs on your motherboard (refer to your

motherboard user’s manual). Working on one connector at a time,

use a very small flathead screwdriver or similar tool to lift up on

the black tab located beside the gold posts (squares). This will

allow you to easily slide out the pins from the USB plug.

2. Working carefully so as not to damage the wires, connectors, or

pins, slowly remove the pin from the connector. Repeat these

steps for each wire you need to change.

3. Working carefully so as not to damage the wires, connectors or

pins, slowly reinsert the pin into the correct slot of the connector

then snap closed the black tab that was lifted in step 1. Repeat

these steps for each wire you need to change.

OOLING

YSTEM

4.1 TRICOOL™EXHAUST FAN

There is an 80 x 25mm TriCool™ fan pre-installed on the right-hand side of the case. It has an external,

three-speed switch that allows you to choose between quiet performance or maximum cooling. The

default speed setting is Low. The fan is mounted so that air blows out of the case. There are externally

accessible switches for these fans located at the rear of your case.

Size: 80 x 25mm TriCool™ fan

Rated Voltage: 12V

Operating Voltage: 10.2V - 13.8V

Speed

(RPM)

Input

Current

Airflow

Static

Pressure

Acoustic

Noise

Input

Power

High

2600

0.2A

(Max.)

0.96 m³ / min

(34 CFM)

3.04mm-H2O

(0.12 inch-H2O)

30 dBA

2.4W

Medium

2000

0.15A

0.74 m³ / min

(26 CFM)

1.79mm-H2O

(0.07 inch-H2O)

24.3 dBA

1.8W

Low

1500

0.1A

0.55 m³ / min

(20 CFM)

1.0mm-H2O

(0.03 inch-H2O)

18.05 dBA

1.2W

Note: The minimum voltage to start a TriCool™ fan is 5V. We recommend that you set the fan

speed switch to High if you choose to connect the fan(s) to a fan control device. A fan

control device regulates the fan speed by varying the voltage, which may start as low as

4.5V to 5V. Connecting a TriCool™ fan set on Medium or Low to a fan-control device may

result in the fan not being able to start because the already lowered voltage from the fan

control device will be further reduced by the TriCool™ circuitry below 5V.

Inhaltsverzeichnis

Andere Antec Computerzubehör Handbücher

Antec

Antec Twelve Hundred Bedienungsanleitung

Antec

Antec P190 + 1200 Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-02220-0 Bedienungsanleitung

Antec

Antec SONATA II Bedienungsanleitung

Antec

Antec VSK-2000 Bedienungsanleitung

Antec

Antec KS 382 Bedienungsanleitung

Antec

Antec TAKE 3 3U RACKMOUNT CASE Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-03270-4 Bedienungsanleitung

Antec

Antec SONATA II Bedienungsanleitung

Antec

Antec ONE S Bedienungsanleitung

Antec

Antec Atlas Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-02267-5 Bedienungsanleitung

Antec

Antec ARIA Bedienungsanleitung

Antec

Antec Nine Hundred Bedienungsanleitung

Antec

Antec TITAN 550 550 Bedienungsanleitung

Antec

Antec Six Hundred Bedienungsanleitung

Antec

Antec SKELETON Bedienungsanleitung

Antec

Antec Quiet Computing Mini Skeleton-90 Bedienungsanleitung

Antec

Antec Perfomance PLUS600 Series Bedienungsanleitung

Antec

Antec Dark Fleet DF-85 Bedienungsanleitung

Antec

Antec Nine Hundred Bedienungsanleitung

Antec

Antec Perfomance Plus 1000 Series Bedienungsanleitung

Antec

Antec SOLO II Bedienungsanleitung

Antec

Antec NSK 4480 Bedienungsanleitung

Beliebte Computerzubehör Handbücher anderer Marken

Motorola

Motorola ATRIX Bedienungsanleitung

HP USB Media Docking Station Bedienungsanleitung

Cherry

Cherry B.UNLIMITED 3.0 Bedienungsanleitung

Logitech

Logitech IO2 Bedienungsanleitung

ARM

ARM DSTREAM-ST Bedienungsanleitung

Bartec

Bartec TC 7 Series Bedienungsanleitung

Philips

Philips SPC3540 Bedienungsanleitung

Logitech

Logitech mk220 Bedienungsanleitung

SilverStone

SilverStone LC02 Bedienungsanleitung

Flexispot

Flexispot ML2B Bedienungsanleitung

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Bedienungsanleitung

Adam Equipment

Adam Equipment RS-485 Bedienungsanleitung

Vivo

Vivo MOUNT-KB05-4DW Bedienungsanleitung

Kvaser

Kvaser Memorator Professional Bedienungsanleitung

DRC

DRC D-Imaging Bedienungsanleitung

Sven

Sven Base 305 сombo Bedienungsanleitung

Hama

Hama 108310 Bedienungsanleitung

SpeechWare

SpeechWare FlexyMike FMK03 Bedienungsanleitung