Antec Six Hundred Bedienungsanleitung

SIX HUNDRED

USER’S MANUAL

TABLE OF CONTENTS

INTRODUCTION

1.1 Case Specifications.…..…………………………………………………………………………………..3

1.2 Diagram…………………………………………………………………….…………………………………. 3

HARDWARE INSTALLATION GUIDE

2.1 Setting Up….………………………………………………………………………………………………….4

2.2 Power Supply Installation………………………………………………………………………………4

2.3 Cable Management……………………………………………………………………………………….5

2.4 Motherboard Installation..…………………………………………………………………………….5

2.5 Internal 3.5” Device Installation…………………………………………………………………….6

2.6 Front-Loaded Hot Swap SATA Hard Drive Caddy……………………………………………6

2.7 External 5.25” Device Installation………………………………………………………………….7

CONNECTING THE FRONT I/O PORTS

3.1 USB 2.0 Ports………………………………………………….……………………………………………. 8

3.2 AC’97 / HD Audio Ports……………………….……………………………………………………….. 8

3.3 Switch and LED Connectors……………………………………………………………………………9

3.4 Rewiring Motherboard Header Connections………………………………………………… 9

COOLING SYSTEM

4.1 TriCool™ Fan………………………………………………………………………………………………… 10

4.2 TwoCool™ Fans …………………………………………………………………………………………….11

4.2 Optional Fans.……………………………………………………………………………………………….12

4.3 Washable Air Filters………………………………………..…………………………………………….13

UNDRED

SER

’

ANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that

your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an

improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are

correct.

Disclaimer

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive

instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come

with those components.

The Six Hundred does not come with a power supply unit (PSU). Make sure you choose a power supply

that is compatible with your computer components and has a long enough power harness to reach your

motherboard and peripheral devices. We recommend our TruePower New, EarthWatts Green, or

Signature Series power supplies for the latest ATX specification compliance, broad compatibility, and

energy-saving capabilities.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend taking

the appropriate time and care when working with it. Avoid hurried or careless motions. Please use

reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the

motherboard manual for specific mounting instructions and troubleshooting. Before proceeding, check

the manual for your CPU cooler to find out if there are steps you must take before installing the

motherboard. While installing hardware, keep your case on a flat, stable surface.

Warning

The top rails are not designed to support the weight of

your computer. Please do not use them as handles to

carry your case.

CASE SPECIFICATIONS

Case Type

Gaming Mid Tower

Color

Two Tone (Black/Gunmetal Gray)

Dimensions

211.6mm (W) x 492mm (D) x 491mm (H)

Weight

6.9 kg / 15.3 lb

Cooling

1 x Rear 120mm TwoCool™blue LED fan

1 x Top special 200mm TriCool™blue LED fan

2 x Front 120mm fan mounts (optional)

1 x Side 120mm fan mount (optional)

Drive Bays

10 Drive Bays:

-3 x External 5.25” drive bays

-1 x External front-loaded hot swap 3.5” SATA hard drive caddy

-6 x Internal 3.5” drive bays

Expansion Slots

Motherboard Size

Mini-ITX, microATX, Standard ATX

Front I/O Panel

3 x USB 2.0

AC’97 / HD Audio In and Out

1.2 DIAGRAM

1. 120mm rear TwoCool™ blue LED fan

2. 200mm top TriCool™ blue LED fan

3. 120mm front fans (optional)

4. Washable air filters

5. Motherboard mount

6. CPU cutout

7. Power supply mount

8. 5.25” drive bays

9. 3.5” hot-swap SATA drive bay

10. Front I/O panel

11. 3.5” drive bays

Note: The Six Hundred includes a tool bag with included Product Overview located inside of the case

and behind the front bezel.

HARDWARE INSTALLATION GUIDE

2.1 SETTING UP

1. Place the case upright on a flat, stable surface with the

rear of the case facing you.

2. Remove the side panels by first removing the

thumbscrews at the rear of the case. Then, grip each

panel at the top and bottom and slide it toward the rear

of the case until it detaches from the chassis.

3. To remove the front bezel, depress the tabs on the left

side of the inside of the front bezel, then swing the bezel

open. Once open, it will detach easily from the chassis.

Note: Do not use your fingernails to pry or lift the panels.

2.2 POWER SUPPLY INSTALLATION

1. With the case upright, place the power supply on the

bottom of the case.

Note: Power supplies with fans on the bottom of the

power supply will need to be mounted so that the

fan is facing the top of the case. The Six Hundred

provides mounting holes for power supplies with

standard mounting layouts to be installed right-

side-up or upside down.

2. Push the power supply to the back of the case and align

the mounting holes.

3. Attach the power supply to the case with the screws

provided.

2.3CABLE MANAGEMENT

There is a cable management compartment behind the 3.5” drive cage.

You can tuck or route excess cables in this compartment.

1. Open the right side panel as described in section 2.1.

2. Locate the cable management compartment with cable ties located

behind the walls of the 3.5” drive cage.

3. Tuck or route your excess cables to the compartment. This will keep

the cables from interfering with airflow in your case and help with

cooling.

4. Use the cable ties provided to hold them in place.

2.4MOTHERBOARD INSTALLATION

1. Lay the case down, with the open side facing up.

The drive cages and power supply should be visible.

2. Make sure you have the correct I/O panel for your

motherboard. If the panel provided with the case

isn’t suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Align your motherboard with the standoff holes and

remember which holes are lined up. Not all

motherboards will match with all the provided

holes; this is normal and won’t affect its

functionality.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the

motherboard back in.

6. Screw in your motherboard to the standoffs with

the provided Phillips-head screws.

Note: The Six Hundred comes with a CPU cutout on the motherboard tray, which will allow you to

change your CPU heatsink without removing the motherboard.

2.5INTERNAL 3.5” DEVICE INSTALLATION

The Six Hundred provides space for up to six 3.5” hard

drives. Before you begin, remove the side panels and

front bezel of the case as described in section 2.1. Behind

the front bezel there is a fan cage which provides space

for up to two fans at the front of the case.

1. Open the fan cage by pressing both clips to release

it, then swing it open and detach it from the chassis.

2. Insert your 3.5” device into the 3.5” drive cage from

the front of the case until the mounting holes align

with the screw holes in the cage.

3. Fasten the device in place with the provided screws.

4. Mount any other 3.5” HDD devices accordingly.

5. Connect the appropriate power and data cables to

the device(s).

6. Replace the fan cage.

2.6 FRONT-LOADED HOT SWAP SATA HARD DRIVE CADDY

This case comes with a built-in, externally accessible 3.5”

SATA drive bay where you can load/unload your drive

without shutting down your computer.

Note: Before you can use the hot swap feature,

you must install all related drivers that come

with your motherboard and turn on the

“AHCI” function in the BIOS to activate the

hot swap feature.

Loading:

1. Align your SATA HDD with the drive bay with the

connector facing the case.

2. Push the HDD all the way into the bay until it locks

into position.

Unloading:

1. Ensure that your HDD is not in use.

1. Push the release button on the left-hand side of the

drive bay and pull the HDD free.

2.7EXTERNAL 5.25” DEVICE INSTALLATION

There are three externally accessible 5.25” drive bays. Before you begin,

remove both side panels and front bezel as detailed in section 2.1.

1. Remove the drive bay faceplate by applying pressure to the inside

of the plate to loosen, then swing back and forth until it pops free

of the bezel.

2. Slide your 5.25” device into the bay from the front of the case.

3. Secure the drive into position in the drive cage using the provided

screws.

4. Mount any other 5.25” devices accordingly.

5. Connect the appropriate power and data cables to your device(s).

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative Signal

Positive Signal

Ground

Key (No Connection)

Empty

Signal

Names

(HDA)

Signal

Names

(AC’97)

MIC2

MIC In

AGND

GND

MIC2

MIC Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Key (no pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

ONNECTING THE

RONT

I/O

ORTS

3.1 USB 2.0

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the

motherboard user’s manual to ensure that it matches the table below:

3.2AC’97 /HD AUDIO PORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)

connector linked to the front panel of the case.

You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the

internal audio connectors from your motherboard or sound card and connect the corresponding audio

cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system

supports both standards, only use one connector.

1 2

9 10

3.3POWER SWITCH /RESET SWITCH /HARD DISK DRIVE LED CONNECTORS

Connected to your front panel are LED and switch leads for power, reset, and

HDD LED activity. Attach these to the corresponding connectors on your

motherboard. Consult your motherboard manual for specific pin header

locations. For LEDs, colored wires are positive ( + ). White or black wires are

negative ( –). If the LED does not light up when the system is powered on, try

reversing the connection. For more information on connecting LEDs to your

motherboard, see your motherboard user’s manual.

Note: Polarity (positive and negative) does not matter for switches.

3.4REWIRING MOTHERBOARD HEADER CONNECTIONS

There may come a time when you need to reconfigure the pin-out of a motherboard header connector.

Examples could be for your USB header, audio input header, or some other front panel connector such

as the Power Button connector.

Before performing any work, please refer to your motherboard user’s manual or your motherboard

manufacturer's website to be sure of the pin-out needed for your connector. We strongly recommend

making a notated drawing before beginning work so that you can recover if your work gets disturbed.

1. Determine which wires you need to remove in order to rewire your

plug to match the USB pin-outs on your motherboard (refer to your

motherboard user’s manual). Working on one connector at a time,

use a very small flathead screwdriver or similar tool to lift up on

the black tab located beside the gold posts (squares). This will

allow you to easily slide out the pins from the USB plug.

2. Working carefully so as not to damage the wires, connectors, or

pins, slowly remove the pin from the connector. Repeat these

steps for each wire you need to change.

3. Working carefully so as not to damage the wires, connectors or

pins, slowly reinsert the pin into the correct slot of the connector,

then snap closed the black tab that was lifted in step 1. Repeat

these steps for each wire you need to change.

Inhaltsverzeichnis

Andere Antec Computerzubehör Handbücher

Antec

Antec SX1030 Bedienungsanleitung

Antec

Antec P183 Bedienungsanleitung

Antec

Antec 4U Bedienungsanleitung

Antec

Antec Solo Bedienungsanleitung

Antec

Antec P100 Bedienungsanleitung

Antec

Antec Quiet Computing Two Hundred Bedienungsanleitung

Antec

Antec ONE S Bedienungsanleitung

Antec

Antec P190 + 1200 Bedienungsanleitung

Antec

Antec Quiet Computing Mini Skeleton-90 Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-03270-4 Bedienungsanleitung

Antec

Antec Sonata III Bedienungsanleitung

Antec

Antec SONATA II Bedienungsanleitung

Antec

Antec SX1000II Series Bedienungsanleitung

Antec

Antec ISK 300-150 Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-02267-5 Bedienungsanleitung

Antec

Antec TWO HUNDRED Bedienungsanleitung

Antec

Antec NSK 4480 Bedienungsanleitung

Antec

Antec DF-500 Technisches Handbuch

Antec

Antec KS-388 Bedienungsanleitung

Antec

Antec Quiet Computing 0761345-03203-2 Bedienungsanleitung

Antec

Antec Perfomance PLUS600 Series Bedienungsanleitung

Antec

Antec Atlas Bedienungsanleitung

Antec

Antec Dark Fleet DF-85 Bedienungsanleitung

Antec

Antec Dark Fleet DF-30 Bedienungsanleitung

Beliebte Computerzubehör Handbücher anderer Marken

Motorola

Motorola ATRIX Bedienungsanleitung

HP USB Media Docking Station Bedienungsanleitung

Cherry

Cherry B.UNLIMITED 3.0 Bedienungsanleitung

Logitech

Logitech IO2 Bedienungsanleitung

ARM

ARM DSTREAM-ST Bedienungsanleitung

Bartec

Bartec TC 7 Series Bedienungsanleitung

Philips

Philips SPC3540 Bedienungsanleitung

Logitech

Logitech mk220 Bedienungsanleitung

SilverStone

SilverStone LC02 Bedienungsanleitung

Flexispot

Flexispot ML2B Bedienungsanleitung

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Bedienungsanleitung

Adam Equipment

Adam Equipment RS-485 Bedienungsanleitung

Vivo

Vivo MOUNT-KB05-4DW Bedienungsanleitung

Kvaser

Kvaser Memorator Professional Bedienungsanleitung

DRC

DRC D-Imaging Bedienungsanleitung

Sven

Sven Base 305 сombo Bedienungsanleitung

Hama

Hama 108310 Bedienungsanleitung

SpeechWare

SpeechWare FlexyMike FMK03 Bedienungsanleitung