Antrica ANT-48100 Bedienungsanleitung
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 1
ANT-48100 User Manual
1 Channel Transcoder
(4 Channel Decoder)
Contents
Overview
1.0 Whats in the box
2.0 Setting up the ANT-48100
3.0 Configuring the ANT-48100
4.0 Network
5.0 Operation Mode
6.0 Encoder
7.0 Decoder
8.0 Transcoder
9.0 Mixer Mode
10.0 Display
11.0 Extensions
12.0 System
13.0 Other Information
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 2
Overview
The ANT-48100 TRANSCODER is a highly flexible IP to IP transcoder. Featuring up
to 4 channels of decoding on one Ethernet port (NIC) and 1 channel of re-encoding
(Transcoding) on a second Ethernet Port (NIC). This transcoder is intended for IP to
IP transcoding without offering any local video inputs or outputs. The Transcoder
engine can take up to 4 decoded streams and re encode them as a 1x1 or 2x2
image with a single stream (no secondary stream is available) . The decoder block
can decode 1-4 streams then combine them as a quad image or in the case of one
decoded stream a single image. These quad and single images can also be scaled
to 1080P 720P and 576P resolutions. Additionally the decoder engine can decode
URLs or pre recorded video files. SRT decoding is supported.
Once decoded and scaled the images pass to the Encoder engine. The encoder can
then re-encode (transcode) these decoded streams as HTTP RTSP RTP MPEG-TS ,
RTMP and SRT streams on to a completely independent LAN Network Interface.
As the Transcoder features two independent Network interfaces it acts as an
effective Video stream air gap between two networks.
1.What’s in the Box
The ANT-48100 box contains
- ANT-48100 Transcoder
-12 Volt Power converter (requires an IEC AC mains lead)
-UK/EU/USA or China IEC 110/240v AC Lead (depending on your location)
-HDMI leads x1
-1 sets of stereo Audio line input cables
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 3
2. Setting up the ANT-48100
Connect the ANT-48100 to a laptop or PC via an Ethernet switch using standard
ethernet cables.
Connect the Output Video using an HDMI OUTPUT to a suitable monitor. Connect
the HDMI input to a suitable HDMI source.
Connect the 12 volt power input and switch on.
The ANT-48100 will take approximately 1 minute to boot up. You will see there are 3
LEDS on the front panel …Power, Not Used and LAN. On power up the RED LED
will illuminate and the Green LAN LED will illuminate if connected via ethernet to a
switch or laptop PC. You are now ready to setup the ANT-48100 Transcoder
3. ANT-48100 IP addresses and Log In
The ANT-48100 default IP address is
192.168.1.168 (Encoder IP output) and
192.168.1.160 (Decoder IP Input). Please set
the laptop/PC Ethernet IP address to be in the
same sub-domain e.g 192.168.1.XXX
Open Chrome to view settings and Preview
video (or other up to date browser to just view
settings without video preview) and browse to
192.168.1.168/160 You will be asked to LOGIN: User : admin , password: admin
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 4
adm
adm
4.0 Setup of the ANT-48100 in IP INPUT
(Decoder) mode (192.168.1.160)
4.1 Status
The status tab will show you information on the IP Input settings . This is effectively a
decoder within the transcoder and can decode up to 4 streams or files. This screen
will show if you are in 1x1 mode (1-1 transcode) or 2x2 mode (4 channels decoded
and arranged as a quad image then transcoded) . The input URLs or files are shown
here
4.2 Network
This section defines the network settings of the IP Ethernet input port. NOTE! The
ANT-48100 has two ethernet ports (NICs) which are independent . This setting is for
the Transcoder IP input (decode)
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 5
4.3 Video Source
Video source has 3 sub sections (tabs): On protocol Video , P2P video and SRT
settings
4.31 On Protocol Video XXXXXX?????
Output Resolution: This allows you to set the resolution of the decoded image/
images prior to re encoding
Network Caching: This is a buffer for the decoder section and helps with Network
jitter but as a result introduces latency in the overall Transcode process.
MPTS Program: XXXXXXXXXXXXX????
Private Protocol: On or OFF XXXXXXXXXXX???
Path Setting: This is either a URL or a .SDP file location for using as the source of
the decoder section
Split Mode (if using a URL): Select 1x1 or 2x2 mode (quad) for decoding
Input: 1-4: These are the URLs for the 4 decoded inputs . Generally you would use
1 input in 1x1 mode or 2,3 or 4 inputs for 2x2 mode .
Audio Channel: This defines which URL Input you will be using as the source of the
audio . Enter XXXXXXXXXX in this section
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 6
4.3.2 P2P Video
In this section you are able to XXXXXXX
Intranet Search or Manual input: Allows you to XXXXXXXX
Play: This will enable XXXXXXX
4.3.3 SRT Settings
This section allows Secure Reliable Transport settings to be input if XXXXXXXX
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 7
4.4 System
System Settings Tab: This allows the Decoder section of the transcoder to be
Factory reset or rebooted
Change Password: Allows for the default admin password or previously used
password to be changed.
Update: This allows firmware for the decoder section to be upgraded
Version: The firmware currently installed for the Decoder part of the Transcoder.
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 8
Timing Reboot: Allows the Decoder section to be rebooted automatically every N
Hours ( 0-200 Hours)
5.0 Setup of the ANT-48100 in IP OUTPUT
(Encoder) mode (192.168.1.168)
5.1 Status
Status shows information about the Encoder section of the ANT-48100 Transcoder
and is broken down into 4 sections:
Access Address: The URL of the encoded stream depending what stream method
is selected HTTP RTSP RTP etc .
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 9
Video Parameters: Defines the resolution and frame rate of the encoder input being
supplied by the decoder section.
Hardware Status: A visual indication of XXXXXXX
Preview: Allows a preview of the encoded video stream if using Chrome as a
browser. XXXXXXX
Antrica Quick Start Guide
ANT-48100 Series V12021
Page 10
Andere Handbücher für ANT-48100
1
Inhaltsverzeichnis
Andere Antrica Transcoder Handbücher
Beliebte Transcoder Handbücher anderer Marken
ASTRO
ASTRO U 224 Bedienungsanleitung
scope
scope Connexions CX5 Bedienungsanleitung
Hangzhou Dibsys Technologies Co., Ltd.
Hangzhou Dibsys Technologies Co., Ltd. Caster-T322 Bedienungsanleitung
scope
scope LARYNGOSCOPE Bedienungsanleitung
scope
scope Connexions CX5E Bedienungsanleitung
Kramer
Kramer FC-404NETxI Bedienungsanleitung