Anvil VRX1200/330 Bedienungsanleitung

Stainless Steel Counter Top Servery/Prep Refrigerators

Models:

VRX1200/330 VRX1500/330 VRX1800/330 VRX2000/330

Table Of Contents

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Pack Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Fit Glass Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Storing Food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Turn On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Lock/Unlock the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Enter the Parameter Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Manual Defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cleaning, Care & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cleaning the Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Tips

• Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any

repairs if required. Do not remove any components or service panels on

this product.

• Consult Local and National Standards to comply with the following:

• Health and Safety at Work Legislation

• BS EN Codes of Practice

• Fire Precautions

• IEE Wiring Regulations

• Building Regulations

• DO NOT use jet/pressure washers to clean the appliance.

• DO NOT use the appliance outside.

• DO NOT use this appliance to store medical supplies.

• Always carry, store and handle the appliance in a vertical position and

move by holding the base of the appliance.

• Always switch off and disconnect the power supply to the unit before

cleaning.

• Keep all packaging away from children. Dispose of the packaging in

accordance with the regulations of local authorities.

• If the power cord is damaged, it must be replaced by a RWA agent or

a recommended qualified technician in order to avoid a hazard.

Product Description

VRX1200/330- 5 x ¼ Container Refrigerated Counter Top/Servery Prep

VRX1500/330- 7 x ¼ Container Refrigerated Counter Top/Servery Prep

VRX1800/330- 9 x ¼ Container Refrigerated Counter Top/Servery Prep

VRX2000/330- 10 x ¼ Container Refrigerated Counter Top/Servery Prep

Introduction

Please take a few moments to carefully read through this manual. Correct

maintenance and operation of this machine will provide the best possible

performance from your RWA product.

Pack Contents

The following is included:

RWA prides itself on quality and serv ice, ensuring that at the time of

packaging the contents are supplied fully functional and free of damage.

Should you find any damage as a result of transit, please contact your RWA

dealer immediately.

Installation

1. Remove the appliance from the packaging. Make sure that all protective

plastic film and coatings are thoroughly removed from all surfaces.

2. Maintain a distance of 20cm (7 inches) between the unit and walls or

other objects for ventilation. Increase this distance if the obstacle is a

heat source.

3. Set the brakes on the castors to keep the appliance in position.

Fit Glass Panels

1. Screw the collars to the rim of the appliance.

2. Slot the two side panels into the collars, with the holes in the glass at

the top.

3. Screw a grub screw into each collar to secure the panels.

4. Slot the rear panel into the collars, with the holes in the glass at the top.

5. Screw a grub screw into each collar to secure the panel.

6. Slot the plastic plugs into each of the holes.

7. Screw the brackets to the inside of each pane using the bolt assemblies.

8. Place the top panel onto the brackets, ensuring all holes line up.

9. Insert the plugs and attach the top panel to the brackets with the bolt

assemblies (see below) .

Operation

Storing Food

To get the best results from your RWA appliance, follow these instructions:

• Only store foodstuffs in the appliance when it has reached the correct

operating temperature.

• Do not obstruct the fans inside the appliance.

Turn On

1. Ensure the power switch is set to [O] and turn on at the socket.

2. Switch on the Power [I]. The current temperature within the appliance

is displayed.

Note: If the unit has been stored in a non-vertical position,

stand it in an upright position for approximately 12 hours

before operation.

• RWA Refrigerator or Freezer

• Top glass panel

• Rear glass panel

• Side glass panels x 2

• Instruction manual

• Collars x 6

• Brackets x 7

• Grub screws x 7

• Screws x 12

• Plugs x 14

• Gastranorm adaptor bar

• Adjustable feet x 4

Note: Before using the appliance for the first time, clean the

internal cabinet and shelves with soapy water.

Note: Ensure the hole in the collar for the grub screw faces

inwards.

Note: Ensure the screw hole furthest from the edge of the

panel goes to the back of the appliance.

Note: Ensure the soft end of the grub screw is the end making

contact with the glass.

Note: Ensure the short end of the bolt assembly is on the

outside of the panels.

Lock/Unlock the Control Panel

To lock the control panel:

1. Press and hold the UP and DOWN buttons simultaneously for 10 seconds.

2. Pof flashes on the display and the keyboard is locked.

To unlock the control panel:

1. Press and hold the UP and DOWN buttons simultaneously for 10 seconds.

2. Pon flashes on the display and the keyboard is unlocked.

Enter the Parameter Menu

1. Unlock the control panel, if locked.

2. Press and hold the SET button until ‘d1 ’ flashes on the display.

3. Press the SET button repeatedly to scroll to the desired parameter (see below).

Note:

If a button is not pressed for 10 seconds while using the control panel it times out and reverts to standby mode.

When parameters are being set the Setpoint LED will flash on the display.

Parameter Name Description Range

d1 Operating temperature Set the operating temperature of the appliance -2°C to 10°C

d2 Temperature

Differential

The Temperature Differential is the allowed temperature difference above and below the

operating temperature before the compressor starts/cuts off 0 to 20°C

Temperature Range Set the minimum (d3) and maximum (d4) temperatures that the appliance can fluctuate

between

-40°C

d4 95°C

d5 Compressor Activation

Time Intervals Enter the minimum time interval between the compressor turning off after turning on. 0-999 seconds

d6 Maximum Temperature

Differential Alarm

Set an alarm to sound if the temperature inside the appliance exceeds the set operating

temperature by a specified amount 0°C-50°C

d7 Temperature

Differential Alarm Delay Set a delay before the temperature differential alarm is triggered 0-99 minutes

d8 Defrost Cycle Time

Intervals Set the time between each defrost cycle 1-999 hours

d9 Maximum Defrost

Duration

Set the maximum length of the defrost cycle

Note: The defrost duration can be overridden by parameter d10 (below), if the

cut-off temperature is reached before the end of the defrost duration

0-999 minutes

d10Defrost Cut-off

Temperature Set the defrost cut-off temperature -45°C to 50°C

d11Additional Cut-off

Defrost Period

Set an additional amount of defrost time after the defrost cut-off point has been reached (if

required) 0-99 minutes

d12Delayed Actual

Temperature Display

Set the length of time the inner temperature of the appliance (before defrost started) is

displayed for after a defrost cycle has finished 0-99 minutes

d13Compressor On/Off

During Defrost Turn the Compressor On or Off during the defrost cycle On (1) or Off (0)

d14Evaporator Drying Time Set the amount of time the compressor remains turned Off after a defrost cycle, reducing the

amount of frost build up 0-99 minutes

=19 Temperature Offset Should there be any variance between measured and actual temperature, the measured

temperature can be offset to compensate -20°C to 20°C

Manual Defrost

The appliance will automatically run a defrost cycle every six hours.

To manually defrost the appliance:

1. Press and hold the DEFROST button for 5 seconds.

2. The defrost cycle will start immediately and the Defrost LED illuminates. The defrost will last a maximum of 30 minutes.

3. Waste water is collected in the waste water tray.

Cleaning, Care & Maintenance

• Switch off and disconnect from the power supply before cleaning.

• Clean the interior of the appliance as often as possible.

• Do not use abrasive cleaning agents. These can leave harmful residues.

• Clean the door seal with water only.

• Always wipe dry after cleaning.

• Do not allow water used in cleaning to run through the drain hole into the evaporation pan.

• Take care when cleaning the rear of the appliance. Sharp edges can cut.

• A RWA agent or qualified technician must carry out repairs if required.

Cleaning the Condenser

Periodically cleaning the condenser can extend the life of the appliance.

RWA recommend that a RWA agent or qualified technician clean the condenser.

Parameter Name Description Range

=22 Unit of Measurement Set whether the temperature is displayed in Centigrade or Fahrenheit Centigrade (0) or Fahrenheit (1)

=23 Compressor Operation

During Probe Failure Set whether the compressor runs or remains Off during a temperature probe failure

Compressor runs (1)

Remains Off until fault fixed (0)

Runs intermittently with

parameters =24 and =25 (2)

=24 Compressor ‘On’

Duration Set the length of time the compressor runs during a temperature probe failure 1-99 minutes

=25 Compressor ‘Off’

Duration Set the length of time the compressor remains Off during a temperature probe failure 1-99 minutes

=34 Initial Defrost After

Startup

Set whether the appliance starts a defrost cycle 10 minutes after startup or after the time

programmed in parameter d8 (Defrost Cycle Time Intervals)

Begins 10 minutes after startup

(0) or when programmed (1)

=38 Minimum Temperature

Alarm

Set the display to flash should the inner temperature of the appliance drop beyond a specified

point from the programmed operating temperature 1°C to 50°C

Note: The cycle starts from the time the appliance is initially powered up.

Note: Starting a manual defrost also resets the automatic defrost timer.

The next automatic defrost will start six hours after the manual defrost has finished.

Troubleshooting

If your POLAR appliance develops a fault, please check the following table before making a call to the Helpline.

Error Messages

The following table details the cause and subsequent response of the appliance to errors.

The alarm message will end when the alarm trigger is no longer present, except PF1 and PF2 that require the appliance to be turned Off, then On again.

Technical Specifications

Fault Probable Cause Action

The appliance is not working

The unit is not switched on Check the unit is plugged in correctly and switched on

Plug and lead are damaged Call RWA agent or qualified Technician

Fuse in the plug has blown Replace the fuse

Power supply Check power supply

Internal wiring fault Call RWA agent or qualified Technician

The appliance turns on, but the

temperature is too high/low

Too much ice on the condenser Defrost the appliance

Condenser blocked with dust Call agent or qualified Technician

Doors are not shut properly Check doors are shut and seals are not damaged

Appliance is located near a heat source or air flow

to the condenser is being interrupted

Move the refrigerator to a more suitable location

Ambient temperature is too high Increase ventilation or move appliance to a cooler position

Unsuitable foodstuffs stored in the appliance Remove any excessive hot foodstuffs or blockages to the fan

Appliance is overloaded Reduce the amount of food stored in the appliance

The appliance is leaking water

The appliance is not properly levelled Adjust the screw feet to level the appliance

The discharge outlet is blocked Clear the discharge outlet

Movement of water to the drain is obstructed Clear the floor of the appliance

The water container is damaged Call RWA agent or qualified Technician

The drip tray is overflowing Empty the drip tray

The appliance is unusually loud

The frame has become loose Check and tighten all nuts and screws

The appliance has not been installed in a level or

stable position

Check installation position and change if necessary

Error Message

(flashing) Cause Appliance Response Action

HtAThe inner temperature exceeds

the set maximum temperature

Display flashes

Alternating error message and current temperature

Check Troubleshooting Guide

If problem persists call RWA agent or

qualified Technician

LtAThe inner temperature exceeds

the set minimum temperature

Display flashes

Alternating error message and current temperature

Check Troubleshooting Guide

If problem persists call RWA agent or

qualified Technician

PF1Short circuit or interruption of

the thermostat probe input line Display flashes Compressor operates as specified by

parameter ‘=23 ’

PF2Short circuit or interruption of

the evaporator probe input line Display flashes Defrost as specified by parameters d8 and d9

HLA Inner temperature greater than

90°C

Display flashes

Alternating error message and current temperature Call RWA agent or qualified Technician

LLAInner temperature lower than

-45°C

Display flashes

Alternating error message and current temperature Call RWA agent or qualified Technician

Model Voltage Power Current Temperature

Range Capacity Refrigerant Dimensions

H x W x D (mm)

Weight

(Kg)

VRX1200/330

VRX1500/330

VRX1800/330

VRX2000/330

230V 50Hz 250W 1.1A 2°C to 10°C 5 x Gastranorm ¼ Container 430 x 1200 x 335

230V 50Hz 250W 1.1A 2°C to 10°C 7 x Gastranorm ¼ Container 430 x 1500 x 335

230V 50Hz 250W 1.1A 2°C to 10°C 9 x Gastranorm ¼ Container R134a 430 x 1800 x 335

230V 50Hz 250W 1.1A 2°C to 10°C 10 x Gastranorm ¼ Container R134a 430 x 2000 x 335

Electrical Wiring

RWA appliances are supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard.

The plug is to be connected to a suitable mains socket.

RWA appliances are wired as follows:

• Live wire (coloured brown) to terminal marked L

• Neutral wire (coloured blue) to terminal marked N

• Earth wire (coloured green/yellow) to terminal marked E

All RWA appliances must be earthed, using a dedicated earthing circuit.

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and

federal authorities.

BUFFALO products have been approved to carry the following symbol: