AOpen AK77-600 Max Bedienungsanleitung

TX Power Connecto

SYSFAN1 Connector

GP 8x Expansion Slot

462-pin CPU Socket with Voltage and

Frequency Auto-Detection that supports

MDTMAthlonTM / DuronTM / and AthlonTMXP

(with CPU Overheat Protection circuit to

thlonTMXP CPU only)

VIA

Apollo KT600 Chipset and VT8237

SouthBridge

CPUFAN Connector

184-pin DIMMx3 supports DDR400 max.

to 2GB and DDR333/266 max. to 3GB

FDD Connecto

CD-IN Connecto

IEEE 1394 Connecto

Onboard AC97 CODEC

AUX-IN Connecto

32-bit PCI Expansion Slot x6

(PCI 1 supports slave mode PCI card only)

Dr. LED Connecto

WOL (Wake ON LAN) Connecto

IrDA Connecto

SYSFAN2 Connecto

Front Audio Connecto

Front Panel Connecto

JP14 CMOS Data Clear Jum

Case Open Connecto

JP2

umpe

USB2.0 Connecto

S/PDIF Connecto

BroadCom BCM5705 LAN Controller

JP15

anguage

Selection Jum

JP2 Dr. Voice II Speaker/buzzer

Out

ut Jum

2200μF Low ESR Capacitors

JP28 Keyboard/Mouse Wakeup Jumpe

PS/2 Mouse

Connector

PS/2 Keyboard

Connector USB2.0 Ports

SPP/EPP/ECP

Parallel Port

COM 1 Port COM 2 Port

RJ45 LAN Jack

Line-In

Speaker

Out

MIC-In

USB2.0 Ports

Die Hard BIOS (BIOS 2)

Die Hard BIOS (BIOS 1)

GamePort Connecto

Promise SATA Controller and Connecto

IDE Connector x3 (ATA/66/100/133 supported)

JP24 Die Hard BIOS Select Jumpe

Open reserves the right to revise all the specifications and information contained in this documentation, which are subject to change without notice.

SATA Connectors (provided by VIA VT8237)

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD. Thanks for the

help of saving our earth.

PART NO: 49.8A705.EE1 DOC. NO: AK77600MAX-EG-E0307A

This Easy Installation Guide x 1

Online Manual x 1

EzRestore Guide x 1

40-Wire IDE Cable x 1

80-Wire IDE Cable x 1

Floppy Drive Cable x 1

USB2.0 + Game Port Cable x 1

IEEE 1394 Cable x 1

Serial ATA Cable x 2

Serial ATA Power Cable x 1

S/PDIF Cable x 1

Bonus Pack CD x 1

Norton Anti-Virus CD x 1

I/O Shield x 1

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug theAC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

Pin 1

2. Onboard IEEE 1394 Controller

This motherboard comes with IEEE 1394 controller Agere FW323 onboard. The IEEE 1394 provides data

transfer rate up to 400Mb/s, and USB just has 12Mb/s. Hence, the IEEE 1394 interface can connect with the

devices that need high data transferring performance, such as digital camera, scanner or others IEEE 1394

devices. Please use the proper cable to connect with devices.

IEEE

1394

Port 1

IEEE 1394

Port 2

KEY

1394_PWR

TPB+

GND

TPA-

Shielding GND

1394_PWR

TPB-

GND

TPA+2 1

10 9

Normal

(

default

)

Clear CMOS

Plug in the CPU fan cable to the 3-pin CPUFAN connector. If you have chassis fan, you

can also plug it on SYSFAN1 or SYSFAN2 connector.

5. Setting CPU Voltage & Frequency

4. JP21 K7 Host Clock Selection

3. Installing CPU & Housing Fan

This jumper is used to specify the relationship of PCI and FSB clock. Generally speaking, i

you are not an over-clocker, we recommend you to set it to the default setting. Additionally,

this motherboard also provides “1MHz Stepping Adjustment” feature for overclockers to

adjust CPU FSB frequency via BIOS setup program. If you fix the CPU FSB frequency b

JP21, the “1MHz Stepping Adjustment” range will be changed to 100MHz~248MHz.

Note: Some CPU fans do not have

sensor pin, so that cannot support

fan monitorin

CPUFAN Connector

SYSFAN2 Connector

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be

automatically detected and the range is from 1.1V to 1.85V. It is not

necessary to set CPU Core Voltage

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency

through the BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency / Voltage Control > CPU Speed Setup

Core Frequency = CPU FSB Clock * CPU Ratio

CPU Ratio From 5x to 18x step 0.5x

CPU FSB (By manual

Adjustment) 100~248 by 1MHz stepping adjustment technology

CPU CPU Core

Frequency EV6 Bus Clock Ratio

Athlon 1.33G 1.33GHz 266MHz 10.0x

Athlon 1.4G 1.4GHz 266MHz 10.5x

AthlonXP 1500+ 1.3GHz 266MHz 10.0x

AthlonXP 1600+ 1.4GHz 266MHz 10.5x

AthlonXP 1700+ 1.46GHz 266MHz 11.0x

AthlonXP 1800+ 1.53GHz 266MHz 11.5x

AthlonXP 1900+ 1.6GHz 266MHz 12.0x

AthlonXP 2000+ 1.667GHz 266MHz 12.5x

AthlonXP 2100+ 1.73GHz 266MHz 13x

AthlonXP 2200+ 1.80GHz 266MHz 13.5x

AthlonXP 2400+ 2.0GHz 266MHz 15x

AthlonXP 2500+ (Barton) 1.833GHz 333MHz 11x

AthlonXP 2600+ 2.13GHz 266MHz 16x

AthlonXP 2600+ 2.08GHz 333MHz 12.5x

AthlonXP 2700+ 2.16GHz 333MHz 13x

AthlonXP 2800+ (Barton) 2.083GHz 333MHz 12.5x

AthlonXP 3000+ (Barton) 2.167GHz 333MHz 13x

AthlonXP 3200+ (Barton) 2.2GHz 400MHz 11x

Note: With CPU speed changing rapidly, there might be fastest CPU on the

market by the time you received this installation guide. This table is kindly for

your references only.

SYSFAN1 Connector

Pin 1

JP21 K7 Host Clock

Select Jumper

Warning: VIA®

pollo KT600

chipset supports

200MHz FSB (with

erformance

reaches maximum

400MHz EV6

system bus) and

66MHz AGP clock,

higher clock setting

may cause serious

system damage.

Tip: If your system hangs or fails to boot because of overclocking, simply use <Home>

key to restore the default setting or you can wait the AOpen “Watch Dog ABS” reset

the s

stem in five seconds and s

stem will auto

detect hardware a

ain.

Warning: Supposed you have had adjusted CPU ratio on your current CPU, and you

lan to replace a new CPU. Please use <Home> key or Clear CMOS to restore the

default setting when changing a new CPU, because the system will still implement the

revious CPU setting on the new one.

GND

+12V

SENSOR

Auto detect

(

default

)

100MHz

GND

+12V

SENSOR

GND

+12V

SENSOR

9. Connecting Front Panel Cable

ttach the power LED, speaker, and reset switch connector

to the corresponding pins. If you enable “Suspend Mode

”

item in BIOS Setup, the ACPI & Power LED will kee

flashing while the system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug

this connector to the soft-power switch connector marked

SPWR.

8. Connecting IDE, Floppy Cables

Pin 1 ATA 66/100/133

IDE Connector

FDD Connector

Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDD connector. Be

careful of the pin1 orientation. Wrong orientation may cause system damage.

IDE 2 (Secondary)

IDE 1 (Primary)

6. Connecting IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this module

and application software such as Laplink or Windows 98 Direct Cable Connection, the use

can transfer files to or from laptops, notebooks, PDA devices and printers. This connecto

supports HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function from

BIOS Setup, UART mode select, make sure to have the correct orientation when you plug in

the IrDA connector.

7. Connecting Serial ATA Disk

To connect a Serial ATA disk, you have to have a 7-pin serial ATA cable. Connect two ends

of the serial ATA cable to the serial ATA header on the motherboard and the disk. Like ever

other traditional disk, you also have to connect a power cable. Please be noted that it is a

umper free implement; you don’t need to set jumpers to define a master or slave disk.

When connecting two serial ATA disks, the system will automatically take the one connected

to “Serial ATA 1” header as a master disk.

ATA 66/100/133

IDE 3 (Third)

Pin 1

IrDA Connector

1 KEY

GND

IR_RX

+5V

IR_TX

SATA port 2 (promise)

SATA port 1 (promise)

Promise SATA Chip

SATA port 4 (VIA VT8237)

SATA port 3 (VIA VT8237)

SPEAKER

IDE LED

Power Switch

CPI & Power LED

RESET

SPWR

GND

CPILED-

GND

CPILED+

GND

RESET

GND

+5V

IDE LED

+5V

GND

SPEAKER

11. Support Eight USB 2.0 Ports

10. Front Audio Connector

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

5-6 and 9-10 jumper caps from the Front Audio Connector before connecting the cable.

Please do not remove these 5-6 and 9-10 yellow jumper caps if there’s no audio port on

the front panel.

This motherboard provides eight USB ports to connect USB devices, such as mouse,

keyboard, modem, printer, etc. There are six connectors on the PC99 back panel. You can

use proper cables to connect the other USB connectors to the USB modules or front panel

of chassis. Compared to traditional USB 1.0/1.1 with the speed of 12Mbps, USB 2.0 has a

fancy speed up to 480Mbps, which is 40 times faster than the traditional one.

Pin 1

13. Super 5.1 Channel Audio Effect

This motherboard comes with an ALC650 CODEC, which supports high quality of 5.1

Channel audio effects, bringing you a brand new audio experience. On the strength of the

innovative design of ALC650, you're able to use standard line-jacks for surround audio

output without connecting any external module. To apply this function, you have to install

the audio driver in the Bonus Pack CD as well as an audio application supporting 5.1

Channel. Picture bellow represents the standard location of all speakers in 5.1 Channels

sound track. Please connect the plug of your front speakers to the green “Speaker out”

port, rear speakers’ plug to the blue “Line in” port and both of the center and subwoofe

speakers to the red “MIC in” port.

12. S/PDIF Connector

S/PDIF (Sony/Philips Digital Interface) is a newest audio transfer file format, which provides

impressive audio quality through optical fiber and allows you to enjoy digital audio instead o

analog audio. Through a specific audio cable, you can connect the S/PDIF connector to othe

end of the S/PDIF audio module, which bears S/PDIF digital output. Normally there are two

S/PDIF outputs as shown, one for RCA connector, the most common one used for consume

audio products, and the other for optical connector with better audio quality. Same as outputs,

you can also connect RCA or optical audio products to input connectors on the module and

have the voice or music come out from your computer. However, you must have a S/PDIF

supported speaker/amplifier/decoder with S/PDIF digital input/output to connect to the S/PDIF

digital input/output to make the most out of this function.

S/PDIF Connector

+5V

S/PDIFOUT

GND

S/PDIFIN

S/PDIF Module

S/PDIF

Cable

S/PDIF OUT

S/PDIF IN

(RCA)

S/PDIF IN

(Optical)

S/PDIF OUT

Pin 1

+5V

SBD3-

SBD3+

GND

+5V

SBD2-

SBD2+

GND

USB2 Connector

UD_GND

UD_VCC

UD_RET_R

KEY

UD_RET_L

AUD_MIC

AUD_MIC_BIAS

AUD_FPOUT_R

AUD_FPOUT_L

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

Die Hard BIOS

15. Power-on and Load BIOS Setup

16. AOpen Bonus Pack CD

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU,

SDRAM, HDD, etc.) are good enough for

turbo settin

17. BIOS Upgrade under Windows Environment

You may accomplish BIOS upgrade procedure with EzWinFlash by the following steps,

and it’s STRONGLY RECOMMENDED to close all the applications before you start the

upgrading.

1. Download the new version of BIOS package zip file from AOpen official web site. (ex:

http://english.aopen.com.tw/)

2. Unzip the download BIOS package (ex: WAK77600MAX102.ZIP) with WinZip

(http://www.winzip.com) in Windows environment.

3. Save the unzipped files into a folder, for example, WAK77600MAX102.EXE &

WAK77600MAX102.BIN.

4. Double click on the WAK77600MAX102.EXE, EzWinFlash will detect the model

name and BIOS version of your motherboard. If you had got the wrong BIOS, you will

not be allowed to proceed with the flash steps.

5. You may select preferred language in the main menu, then click [Start Flash] to start

the BIOS upgrade procedure.

6. EzWinFlash will complete all the process automatically, and a dialogue box will pop

up to ask you to restart Windows. You may click [YES] to reboot Windows.

7. Press <Del> at POST to enter BIOS setup, choose "Load Setup Defaults", then

“Save & Exit Setup”. Done!

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win2000/WinXP PnP

information will be refreshed and you probably need to re-configure your system.

Many viruses have been found that they may destroy bios code and data area lately. This

motherboard implements a very effective hardware protection method without any software

or BIOS coding involved, therefore it is 100% virus free. Once your BIOS is crashed, it is

easy to save it back. First step is to set JP24 to Pin2-3 to boot up the system with BIOS 2.

fte

that, please set the JP24 back to Pin1-2, goto Aopen website

(http://download.aopen.com.tw/downloads) to get your BIOS version suited for you

motherboard, and have it downloaded.

Normal

(

default

)

Boot from

BIOS 2

JP24

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this ba

code label on the outside packing or on component side of PCB. For example:

Model name and BIOS version

AK77-600 Max R1.02 Mar. 01. 2003 AOpen Inc.

ward Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AK77-600 Max is model name of motherboard; R1.02 is BIOS version

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS, then plug the ATX power cord correctly.

(For P4 system, please also plug the 4pin(+12V) cord.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reseller

or local distributor for repairing.

Perhaps your VGA card or monitor

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem

eboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Web Site: http://english.aopen.com.tw/

E-mail: Send us email by going through the contact form below.

English http://english.aopen.com.tw/tech/default.htm

Japanese http://www.aopen.co.jp/tech/default.htm

Chinese http://www.aopen.com.tw/tech/default.htm

German http://www.aopencom.de/tech/default.htm

Simplified Chinese http://www.aopen.com.cn/tech/default.htm

Pacific Rim

Open Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5899

Europe

Open Computer b.v.

Tel: 31-73-645-9516

Email: [email protected]

Germany

Open Computer GmbH.

Tel: 49-2131-1243-710

Fax: 49-2131-1243-999

China

艾爾鵬國際貿易(上海)有限公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Japan

Open Japan Inc.

Tel: 81-048-290-1800

Fax: 81-048-290-1820

merica

Open America Inc.

Tel: 1-510-489-8928

Fax: 1-510-489-1998

Online Manual: To download manual, please log on and then select your

preferred language. Under “Type” directory, choose “Manuals” to go to our

manual database. You can also find the manual and EIG in AOpen Bonus Pack.

http://download.aopen.com.tw/downloads

Test Report: We recommend you to choose board/card/device from the

compatibility test reports for assembling your PC. It may prevent incompatibility

problems.

http://english.aopen.com.tw/tech/report/default.htm

FAQ: Here we list problems that users often encounter and FAQ

(Frequently Asked Questions). You may select your preferred language

after log on and find a solution to your problem.

http://club.aopen.com.tw/faq/

Download Software: After log on and having language selected, you may

get the latest updated BIOS/utility and drivers you need under “Type”

directory. In most case, newer versions of drivers and BIOS have solved

earlier bugs or compatibility problems.

http://download.aopen.com.tw/downloads

eForum: AOpen eForum is provided to discuss our products with other users, in

which your problem probably had been discussed before or will be answered.

After log on, you may select your preferred language under “Multi-language”.

http://club.aopen.com.tw/forum/

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well

and should be able to solve your problem efficiently and provide important

reference for you.

symptom before contacting us. The part number, serial number

and BIOS version are also very helpful.

Andere Handbücher für AK77-600 Max

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen AK77 PLUS Bedienungsanleitung

AOpen

AOpen n250a-FR Bedienungsanleitung

AOpen

AOpen AX64 Einrichtungshandbuch

AOpen

AOpen MX3W-E3 Einrichtungshandbuch

AOpen

AOpen AX4G Pro Datenblatt

AOpen

AOpen MX46LS-V Einrichtungshandbuch

AOpen

AOpen AK77-333F Einrichtungshandbuch

AOpen

AOpen AX4B-G2 Datenblatt

AOpen

AOpen MX36LE-N Bedienungsanleitung

AOpen

AOpen AX34 Pro II Einrichtungshandbuch

AOpen

AOpen AK77-8X Datenblatt

AOpen

AOpen AK77-600GN Einrichtungshandbuch

AOpen

AOpen AK79G TUBE Datenblatt

AOpen

AOpen MX46L Datenblatt

AOpen

AOpen AX59PRO Bedienungsanleitung

AOpen

AOpen AK75 Einrichtungshandbuch

AOpen

AOpen MK79G-N Einrichtungshandbuch

AOpen

AOpen AX4B Max Datenblatt

AOpen

AOpen AX4GE Tube-G Einrichtungshandbuch

AOpen

AOpen AX4SPE Max II Einrichtungshandbuch

AOpen

AOpen s760GXm-SL Bedienungsanleitung

AOpen

AOpen MX4LR-GN Datenblatt

AOpen

AOpen MK79G-N Bedienungsanleitung

AOpen

AOpen AK79G MAX Datenblatt

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung