AOpen AK77 PRO Datenblatt

MIC-In

Line-In

Speaker Out

PS/2 Mouse

Connector

PS/2 Keyboard

Connector

USB Port

SPP/EPP/ECP

Parallel Port

COM 1 Port COM 2 Port

Game Port

Resettable Fuse

Keyboard Wake-up Select

Jum

TX Power Connecto

UX Fan Connecto

GP 4x Expansion Slot

462-pin CPU Socket with Voltage

and Frequency Auto-Detection that

supports AMD®Athlon®and Duron®

600MHz~1.4GHz+ CPU

VIA

Apollo KT266 Chipset with

Fansink

CPU Fan Connector with

H/W Monitoring

184-pin DDR SDRAM Slot x3

support maximum up to 3GB

TA/100 IDE RAID Connector x2

(AK77 Plus only)

TA/33/66/100 IDE Connector x2

FDD Connector

CD-IN Connecto

Die Hard BIOS with 100% Virus

Protection (Upgrade Optional)

JP30 Die Hard BIOS Select Jumpe

Onboard AC97 CODEC

Green: AUX-IN Connecto

Red: Modem-IN Connecto

CNR Expansion Slot

32-bit PCI Expansion Slot x5

(PCI 5 supports slave mode PCI card only)

2nd & 3rd USB Port Connecto

Dr. LED Connecto

(Upgrade Optional)

WOM (Wake ON Modem) Connecto

WOL (Wake ON LAN) Connecto

IrDA Connecto

Chassis Fan Connector with

H/W Monitoring

Front Audio Connecto

Front Panel Connecto

JP14 CMOS Data Clear Jumpe

PROMISE

FastTrak 100™ Lite

IDE RAID Controller (AK77 Plus only)

System & RAM Power Indicate LED

Chassis Intrusion Sensor Connecto

JP21 FSB Select Jumper

Pin 1

1. JP14 Clear CMOS

2. JP28 Keyboard Wakeup

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.89A01.012 DOC. NO: AK77P-EG-E0110E

Hard Drive IDE Cable x 1

80-Wire IDE Cable x 1

Floppy Drive Cable x 1

2nd USB Cable x1 (AK77 Plus Only)

Bonus Pack CD disc x 1

Norton Anti-Virus CD x 1

Online Manual x 1

This Easy Installation Guide x 1

This motherboard provides keyboard wake-up function. You can use the JP28 to enable or disable this

function.

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pins 1 & pin2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

Normal Operation

(default) Clear CMOS

Pin 1

Disable

(Default)

Enable

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look for a

(golden) cut edge on the CPU upper interface.

Match Pin 1 and cut edge. Then insert the

CPU into the socket.

3. Press down the CPU socket lever and finish

CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan,

you can also plug it on FAN2 or FAN3 (without H/W monitoring) connector.

5. Setting CPU Voltage & Frequency

4. Installing CPU & Housing Fan

3. Installing CPU

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well, it

may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

GND

+12V

Sensor

Note: Some CPU fans do not have

sensor pin, so that cannot support

fan monitoring.

CPU Fan Connector

Fan3 Connector

GND

+12V

Sensor

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be automatically

detected and the range is from 1.1V to 1.85V. It is not necessary to set CPU Core Voltage

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency / Voltage Control > CPU Speed Setup

Core Frequency = CPU FSB Clock * CPU Ratio

CPU Ratio From 5.5x to 12.5x step 0.5x

CPU FSB (By BIOS table) 100, 102, 105, 108, 110, 113, 115, 117, 120, 122, 124, 133, 136, 138,

140, 142, 144, 147, 152, 154, and 156MHz.

CPU FSB (By manual

Adjustment) FSB=100, 100~129 by 1MHz stepping adjustment technology

FSB=133, 130~248 by 1MHz stepping adjustment technology

CPU CPU Core Frequency EV6 Bus Clock Ratio

Athlon 800 800MHz 200MHz 8.0x

Athlon 850 850MHz 200MHz 8.5x

Athlon 900 900MHz 200MHz 9.0x

Athlon 950 950MHz 200MHz 9.5x

Athlon 1G 1GHz 200MHz 10.0x

Athlon 1.1G 1.1GHz 200MHz 11.0x

Athlon 1.2G 1.2GHz 200MHz 12.0x

Athlon 1.3G 1.3GHz 200MHz 13.0x

Athlon 1.4G 1.4GHz 200MHz 14.0x

Athlon 1G 1GHz 266MHz 7.5x

Athlon 1.13G 1.13GHz 266MHz 8.5x

Athlon 1.2G 1.2GHz 266MHz 9.0x

Athlon 1.33G 1.33GHz 266MHz 10.0x

Athlon 1.4G 1.4GHz 266MHz 10.5x

AthlonXP 1500+ 1.3GHz 266MHz 10.0x

AthlonXP 1600+ 1.4GHz 266MHz 10.5x

AthlonXP 1700+ 1.46GHz 266MHz 11.0x

AthlonXP 1800+ 1.53GHz 266MHz 11.5x

AthlonXP 1900+ 1.6GHz 266MHz 12.0x

Duron 800 800MHz 200MHz 8.0x

Duron 850 850MHz 200MHz 8.5x

Duron 900 900MHz 200MHz 9.0x

Duron 950 950MHz 200MHz 9.5x

Duron 1G 1GHz 200MHz 10.0x

Duron 1.1G 1.1GHz 200MHz 11.0

Tip: If your system hangs or fails to boot because of

overclocking, simply use <Home> key to restore the default

setting (433MHz) or you can wait the AOpen “Watch Dog

Timer” reset the system in five seconds and system will

auto-detect hardware again.

Warning: VIA®Apollo KT266 chipset supports 133MHz FSB (with performance

reaches maximum 266MHz EV6 system bus) and 66MHz AGP clock, higher

clock settin

cause serious s

stem dama

Pin 1

7. Install DIMM Modules

6. JP21 FSB/PCI Clock Ratio

9. Connecting Front Panel Cable

This jumper is used to specify the relationship of PCI and FSB clock. Generally speaking, i

you are not overclockers, we recommend you to set at the default setting. Additionally, this

motherboard also provides “1MHz Stepping Adjustment” feature for overclockers to adjust

CPU FSB frequency via BIOS setup program. Based on the CPU type, the adjustment

range has two levels: 100~129 (FSB=100, such as Athlon 800), 130~248 (FSB=133, such

as Athlon 1000) MHz for your choosing. You may also choose a specific FSB frequency

ranging from 100~117 (say, 105, 110, 115 for example) and 120~156 with reference to a

frequency table in BIOS setup program. If you fix the CPU FSB frequency by JP21, the

“1MHz Stepping Adjustment” range will be changed and following JP21 setting.

This motherboard has installed the DDR SDRAM interface, which allows zero wait state

bursting between the SDRAM and the data buffers at 100 or 133MHz. The three 184-pin

sockets, six banks of DDR SDRAM can be composed of an arbitrary mixture o

1M/2M/4M/8M/16M/32M/64MxN DDR SDRAM with maximum up to 3GB.

Warning: High CPU core voltage

may be able to increase CPU

speed for overclocking, but you

may damage the CPU or reduce

the CPU lifecycle.

Speaker

IDE LED

SPWR

+ ACPI & PWR

LED

Reset

SPWR

GND

ACPI LED-

GND

ACPILED

GND

RESET

GND

IDE LED

GND

SPEAKE

ttach the power LED, speaker, and reset switch connector

to the corresponding pins. If you enable “Suspend Mode

”

item in BIOS Setup, the ACPI & Power LED will kee

flashing while the system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug

this connector to the soft-power switch connector marked

SPWR.

FSB=100MHz

(Default)

DDR

SDRAM

FSB=133MHz

Warning: The AK77 Plus / AK77 Pro

support DDR SDRAM; please do not

install the SDRAM module on the DDR

SDRAM sockets. Otherwise, it will cause

serious damage on memory sockets or

SDRAM module.

8. Connecting IDE, Floppy and IDE RAID Cables

Pin 1 ATA 33/66/100

IDE Connector

FDD Connector

IDE RAID

Connector

(AK77 Plus only) IDE RAID 2 (Secondary)

IDE RAID 1 (Primary)

1 1

Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDC and IDE/IDE

RAID (AK77 Plus only) connector. Be careful of the pin1 orientation. Wrong orientation

may cause system damage.

The ATX power supply uses 20-pin connector shown below. Make sure you plug in the

right direction.

11. Connecting CD / AUX / MODEM

12. Front Audio

9. Connecting ATX Power Connector

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

the jumper cap from the Front Audio Connector before you connect the cable. Do not

remove this yellow jumper cap if housing without an audio port on the front panel.

Low ESR capacito

The CD-IN connector is used to connect CD Audio

cable from CDROM or DVD drive to onboard sound.

The AUX-IN connector is used to connect MPEG

udio cable from MPEG card to onboard sound.

The MODEM-CN connector is used to connect

Mono In/ Mic Out cable from internal modem card to

onboard sound circuit.

MODEM-CN (Red)

Connector Pin1 Pin2 Pin3 Pin4

CD-IN Left GND GND Right

AUX-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

UX-IN

(Green)

CD-IN (Black)

+5V

+3.3V

COM

COM COM

COM

COM COM

-5V

COM

-12V

PS-ON

PW-OK

+12V

5VSB

Pin 1

FP_MIC

FP_VREF

PHONE_R

PHONE_L

GND

+5V

JS1

KEY

1 2

9 10

10. Connect IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this

module and application software such as Laplink or Windows 95 Direct Cable

Connection, the user can transfer files to or from laptops, notebooks, PDA devices and

printers. This connector supports HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function

from BIOS Setup, UART mode select, make sure to have the correct orientation when

you plug in the IrDA connector.

+5V

IR_T

KEY

GND

IR_RX

Pin 1

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

13. Power-on and Load BIOS Setup

14. AOpen Bonus Pack CD 16. BIOS Upgrade

Open Easy Flash is more use

-friendly than traditional flash method. The BIOS binary

file and flash routine are combined together and you simply run a single file to complete

the flash process.

1. Download new BIOS upgrade zipped file from AOpen's web site. For example,

AK77P102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com/) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, AK77P102.BIN & AK77P102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> AK77P102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and you probably need to re-configure your system.

15. Installing Onboard Sound Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and select

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU,

SDRAM, HDD, etc.) are good enough for

turbo settin

This motherboard comes with an AD 1885 AC97 CODEC; you can find the audio drive

from the Bonus Pack CD auto-run menu.

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

AK77 Plus R1.00 Feb. 01. 2001 AOpen Inc.

ward Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AK77 Plus is model name of motherboard; R1.00 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com.tw/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com.tw/tech/report/default.htm

FAQ: The latest FAQ (FrequentlyAsked Questions) may contain a

solution to your problem.

http://www.aopen.com.tw/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com.tw/tech/download/default.htm

News Group: Your problem probably had been answered by our support

engineer or professional users on the news group.

http://www.aopen.com.tw/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem more efficiently than us. After all, their

attitude of service is an important reference for you if next time you want to

buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com.tw/tech/contact/techusa.htm

Japanese http://aojp.aopen.com.tw/tech/contact/techjp.htm

Chinese http://w3.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://aofr.aopen.com.tw/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

Open Inc.

Tel: 886-2-2696-1333

Fax: 886-2-8691-2233

merica

Open America Inc.

Tel:

510

498

8928

Europe

Open Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

Open Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102

China

艾尔鹏国际上海(股)

有限公司

Tel: 49-2102-157700

Fax: 49-2102-157799

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen AX45F-1394 Datenblatt

AOpen

AOpen i915Ga-EFRII Bedienungsanleitung

AOpen

AOpen s661FXm-7S Bedienungsanleitung

AOpen

AOpen AK77-600N Bedienungsanleitung

AOpen

AOpen MX46-800N Datenblatt

AOpen

AOpen AK89 MAX Bedienungsanleitung

AOpen

AOpen i915Gm-IE Datenblatt

AOpen

AOpen s651M Datenblatt

AOpen

AOpen AX37D Plus Datenblatt

AOpen

AOpen AX4B Max Datenblatt

AOpen

AOpen MX46-800N Einrichtungshandbuch

AOpen

AOpen AX4C Max II Einrichtungshandbuch

AOpen

AOpen AK73-1394 Einrichtungshandbuch

AOpen

AOpen AX4LR Bedienungsanleitung

AOpen

AOpen DXPL-U Bedienungsanleitung

AOpen

AOpen i945GTm-VHL Bedienungsanleitung

AOpen

AOpen DX34-U Bedienungsanleitung

AOpen

AOpen MK73LE Einrichtungshandbuch

AOpen

AOpen i915Ga-E Bedienungsanleitung

AOpen

AOpen AX4SPE Max II Datenblatt

AOpen

AOpen AX4BR-U Bedienungsanleitung

AOpen

AOpen Fortress 7000 Bedienungsanleitung

AOpen

AOpen D X37PU-EG-E0110A Datenblatt

AOpen

AOpen AX59PRO Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung