AOpen MK73LE-N Datenblatt

JP13 LAN Select Jumpe

(MK73LE-N Only)

MIC-In

PS/2 Mouse

Connecto

PS/2 Keyboard

Connector USB Port

SPP/EPP/ECP

Parallel Port

COM 1 Port VGA

Connecto

MIDI/Game

Port

Line-In

Speaker

Out

TX Power Connecto

CPUFan Connector

Low ESR Capacitor

462-pin CPU Socket

Supports AMD Duron /

thlon 600MHz~1.4GHz

VIAApollo KLE133 Chipset

PC-100/133 DIMM Socket x2

JP21 CPU FSB Select

TA 33/66/100 IDE Connector x2

FDD Connector

AUX-IN Connector (Green)

WOM Connecto

(Wake On MODEM)

MODEM-CN Connector (Red)

CD-IN Connector (Black)

CNR Slot

Support 2nd USB Port

Fan2 Connecto

Onboard AC’97 CODEC

IrDA Connecto

COM2 Connector

2Mb Flash ROM BIOS

32-bit PCI Slot x3

JP14 Clear CMOS

WOL Connecto

(Wake On LAN)

Front Audio Connecto

Front Panel Connecto

Resettable Fuse

RTL8100 LAN Chip

(

MK73LE-N Onl

Fan3 Connecto

GPO Connector

RJ-45 LAN Connector

(MK73LE-N Only)

1. Clear CMOS Data

2. Installing CPU

Everything you need to boot thi

motherboard is included in thi

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks fo

the help of saving our earth!

PART NO: 49.89E03.001 DOC. NO: MK73LEN-EG-E0110A

80-conductor IDE Cable x 1

Floppy Drive Cable x 1

Bonus Pack CD disc x 1

This Easy Installation Guide x 1

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

Normal Operation

(Default) Clear CMOS

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pin 2-3 for a few seconds.

. Return JP14 to its normal setting by shorting pin 1 & pin2.

5. Connect ATX power cable back to connector PWR2.

1. Pull CPU socket lever and up to 90-degree angle.

2. Locate Pin 1 on the socket and look for a black dot

or cut edge on the CPU upper left. Match Pin 1 and

cut edge. Then insert CPU into the socket.

3. Press down CPU socket lever to finish CPU

installation.

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well,

ou ma

dama

e the CPU.

CPU Pin1

CPU socket

Lever

This jumper is used to specify the relationship of PCI and FSB clock. Generall

speaking, if you are not an overclocker, we recommend you to set at the default setting.

Plug in the CPU fan cable to the 3-pin CPUFAN connector. If you have housing fan,

you can also plug it on FAN2 connector.

JP21 FSB Select Jumper

5. Setting CPU Voltage & Frequency

4. Select FSB/PCI Clock

3. Installing CPU & Housing Fan

Home

Tip: If your system hangs or fails to boot

because of overclocking, simply use <Home>

key to restore the default setting.

CPU Core Voltage Auto-Detection

This motherboard supports CPU VID function. The CPU core voltage will be automatically

detected from 1.1V~1.85V. It is not necessary to set CPU Core Voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency/Voltage Control > CPU Host Clock (CPU/PCI)

Core Frequency = CPU FSB Clock * CPU Ratio

CPU Ratio 5.5x, 6x, 6.5x …..12x, 12.5x, 13x

CPU FSB 100.2, 102, 104, 106, 107, 108, 109, 110, 111, 112, 113, 114,

115, 116, 118, 120, 133, 136, 140, 145, 150, 155, 160, and

166MHz

CPU CPU Core

Frequency FSB Clock Ratio

Athlon 800 800MHz 200MHz 8x

Athlon 850 850MHz 200MHz 8.5x

Athlon 900 900MHz 200MHz 9x

Athlon 950 950MHz 200MHz 9.5x

Athlon 1G 1GHz 200MHz 10x

Athlon 1.1G 1.1GHz 200MHz 11x

Athlon 1.2G 1.2GHz 200MHz 12x

Athlon 1.3G 1.3GHz 200MHz 13x

Athlon 1.4G 1.4GHz 200MHz 14x

Athlon 1G 1GHz 266Mhz 7.5x

Athlon 1.13G 1.13GHz 266MHz 8.5x

Athlon 1.2G 1.2GHz 266MHz 9.0x

Athlon 1.33G 1.33GHz 266MHz 10x

Athlon 1.4G 1.4GHz 266MHz 10.5x

Athlon XP 1500+ 1.3GHz 266MHz 10x

Athlon XP 1600+ 1.4GHz 266MHz 10.5x

Athlon XP 1700+ 1.46GHz 266MHz 11x

Athlon XP 1800+ 1.53GHz 266MHz 11.5x

Athlon XP 1900+ 1.6GHz 266MHz 12x

Duron 800 800MHz 200MHz 8x

Duron 850 850MHz 200MHz 8.5x

Duron 900 900MHz 200MHz 9x

Duron 950 950MHz 200MHz 9.5x

Duron 1G 1GHz 200MHz 10x

Duron 1.1G 1.1GHz 200MHz 11x

Note: Some CPU fans do not have

sensor pin, so that they cannot

support fan monitoring.

CPUFAN

FAN2

FAN3

Pin 1

FSB=124MHz~

166MHz

FSB=100MHz~

124MHz

GND

+12V

SENSOR

GND

+12V

SENSOR

Secondary

Slave (4th)

Primary

Master (1st)

Primary

Slave (2nd)

Secondary

Master (3rd)

Pin 1

7. Connecting IDE and Floppy Cable

6. CNR Expansion Slots 8. JP13 LAN Select Jumper (MK73LE-N Only)

9. Connecting Front Panel Cable

Connect 34-pin floppy cable and 40-pin IDE cable to floppy connector FDC and IDE

connector. The blue connector is IDE1 for clear identification. Beware of the pin1

orientation. Wrong orientation may cause system damage.

This jumper allows you to enable or disable the LAN onboard function by adjusting the

position of yellow cap.

IDE2 (Secondary)

Pin 1

IDE1 (Primary)

FDD Connector

IDE Connector

Attach the power LED, ACPI, speaker, power and reset switch connectors to the

corresponding pins. If you enable “Suspend Mode” item in BIOS Setup, the ACPI & Power

LED will keep flashing while the system is in suspend mode.

Locate the power switch cable from your ATX housing. It is 2-pin female connector from the

housing front panel. Plug this connector to the soft-power switch connector marked SPWR.

Speaker

IDE LED

Power Switch

+ACPI &

Power LED

Reset

CNR (Communication and Network Riser) is a riser card specification to replace the

MR (Audio / Modem Riser) that supports V.90 analog modem, multi-channel audio, and

phone-line based networking. This motherboard implements sound CODEC on board

(can be disabled in BIOS), but reserves CNR slot for the option of modem function. Note

that you can still use PCI modem card. And due to hardware limitation, if the

motherboard you purchased implements an optional Creative CT5880 Audio Controller,

then there will not be CNR expansion slot on your motherboard. Pin 1

Enable Disable

You can install LAN Driver under Windows95/98, Windows NT and Windows 2000 for Realtek

RTL8139 Family (RTL8100 included) PCI Fast Ethernet adapter by following steps.

Installing driver procedure on Microsoft Windows 95 :

-----------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which driver you

would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95\WIN95A (for Windows 95 and Win95A) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95 (for Windows 95 OSR2).

3. Follow the procedure and insert Windows 95 system disk to complete setup step.

4. Windows 95 will finish the other installation procedures automatically, and then restart your

system.

Installing driver for Win98/Win98 SE/Windows2000/Windows ME :

-------------------------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which driver you

would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN98 (for Windows 98/98 SE) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN2000 (for Windows 2000) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\Windows ME (for Windows ME)

3. Follow the procedure and insert your system disk (Win98/Win98 SE/Windows2000/Windows

ME) to complete setup step.

4. Win98/Win98 SE/Windows2000/Windows ME will finish the other installation procedures

automatically, and then restart your system.

12. Power-on and Load BIOS Setup

13. Installing LAN Driver (MK73LE-N Only)

10. Installing Front Audio

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector.

11. Connecting CD / MODEM / AUX-IN

Del

Warning: Please avoid using

"Load Turbo Defaults", unless you

are sure your system components

(CPU, DRAM, HDD etc.) are good

enough for turbo setting.

The CD-IN connector is used to connect CD Audio

cable from CDROM or DVD drive to onboard sound.

The MODEM-CN connector is used to connect

Mono In/ Mic Out cable from internal modem card to

onboard sound circuit.

The AUX-IN connector is used to connect MPEG

udio cable from MPEG card to onboard sound.

CD-IN

Connector Pin1 Pin2 Pin3 Pin4

CD-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

AUX-IN Left GND GND Right

MODEM-CN

AUX-IN

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

FP_MIC

FP_VREF

PHONE_R

PHONE_L

GND

+5V

1 2

9 10

Pin 1

14. AOpen Bonus Pack CD

15. Installing Onboard AGP Driver 17. BIOS Upgrade

Open Easy Flash is user-friendlier than traditional flash method. The BIOS binary file

and flash routine are combined together and you simply run a single file to complete the

flash process.

1. Download new BIOS upgrade zipped file from AOpen's web site. For example,

MK73LEN102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com/) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, MK73LEN102.BIN & MK73LEN102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> MK73LEN102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and

robabl

need to re

confi

ure

our s

stem.

16. Installing Onboard Audio Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and

select model name. This motherboard comes with an AC97 CODEC. You can find the audio driver from

the Bonus Pack CD disc autorun menu.

VIA Apollo KLE133 chipsets integrates a 2D/3D graphics accelerator and provides

GP 2X/4X incredible performance to access main memory at over 1GB/s. You can

find the AGP driver from the autorun menu of Bonus Pack CD.

If you encounter any trouble to boot you system, follow the

procedures accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

MK73LE-N R1.00 Oct. 01. 2001 AOpen Inc.

ward Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

MK73LE-N is model name of motherboard, R1.00 is BIOS version.

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com.tw/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com.tw/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com.tw/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com.tw/tech/download/default.htm

News Group: Your problem probably had been answered by our support

engineers or professional users on the news group.

http://www.aopen.com.tw/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem more efficiently. After all, it is an

important reference when you want to buy something else from them next

time.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com.tw/tech/contact/techusa.htm

Japanese http://aojp.aopen.com.tw/tech/contact/techjp.htm

Chinese http://w3.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://aofr.aopen.com.tw/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

Open Inc.

Tel: 886-2-2696-1333

Fax: 886-2-8691-2233

merica

Open America Inc.

Tel: 1-510-498-8928

Fax: 1-408-922-2935, 1-408-432-0496

Europe

Open Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

Open Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)

有限公司

Tel: 86-21-62258622

Fax: 86-21-62257926

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung