AOpen MX4B-533 Bedienungsanleitung

PS/2 Mouse

Connector SPP/EPP/ECP Parallel Port MIDI/Game Port

MIC-In

Line-In

Speaker Out

PS/2 Keyboard

Connector USB Port COM 1 Port COM 2 Port

FAN3 Connecto

CD-IN Connecto

CNR Ex

ansion Slot

IrDA Connecto

Front Panel Connecto

JP14 CMOS Clear Jum

Dr. LED Connecto

Resettable Fuse

478-pin CPU socket with Voltage and

Frequency Auto-detection supporting

Intel®Pentium®4

JP1 Buzzer Select Jum

32-bit PCI Expansion Slot x3

CPU Fan Connecto

184-pin DIMM Socket x2 support

DDR200/266 DDR SDRAM

maximum up to 2 GB

Intel

845E chipset with MCH,

ICH4 that supports LAN, Ultra

ATA/100, SDRAM Solution

Low ESR Capacitors

TX Power Connecto

-IN Connecto

4-pin 12V. ATX Power Connecto

4MB Flash ROM BIOS

Chassis Intrusion Connecto

Front Audio Connecto

WOL Connecto

WOM Connecto

FDD Connecto

JP28 Keyboard/Mouse Wakeup

Enable/Disable Jumper

TA/33/66/100 IDE Connector x2

FAN2 Connecto

GP Expansion Slot

USB2.0 Connectors

S/PDIF Connecto

LAN Connector

This motherboard comes with a 20-pin and 4-pin ATX power connector as shown below. Make sure you plug

in the right direction. We strongly recommend you to insert the 4-pin connector before connecting the 20-pin

connector.

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD. Thanks for the

help of saving our earth.

PART NO: 49.88W10.E01 DOC. NO: MX4B533-EG-E0205A

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug theAC power.

2. RemoveATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. ConnectATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

2. Connecting ATX Power Connector

This Motherboard x1

This Easy Installation Guide x1

ATA Cable x1

Floppy Disk Drive Cable x1

Bonus Pack CD x1

Registration Card

Ground

12V

Ground

COM

-5

+12

5VSB

PO-O

COM

PS-ON

COM

-12V

+3.3V

COM

+5V

COM

Pin 1

Normal

(

default

)

Clear CMOS

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look fo

a (golden) cut edge on the CPU uppe

interface. Match Pin 1 and cut edge.

Then insert the CPU into the socket.

3. Press down the CPU socket lever and

finish CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan, you

can also plug it in FAN2 or FAN3 connector.

CPU Ratio 8x, 9x, 10x… 21x, 22x, 23x, 24x

CPU FSB 100~248MHz by 1MHz stepping

Northwood

CPU CPU Core

Frequency FSB

Clock System

Bus Ratio

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.6G 1600MHz 133MHz 533MHz 12x

Pentium 4 1.7G 1700MHz 133MHz 533MHz 13x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

Pentium 4 2.2G 2200MHz 100MHz 400MHz 22x

Pentium 4 2.4G 2400MHz 100MHz 400MHz 24x

Pentium 4 2.4G 2400MHz 133MHz 533MHz 18x

5. Setting CPU Voltage & Frequency

Setting CPU Core Voltage

This motherboard supports CPU VID function. The CPU core voltage will be automaticall

detected and the range is from 1.10V to 1.85V. It is not necessary to set CPU core

voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency / Voltage Control > CPU Speed Setting

Core Frequency = CPU FSB Clock * CPU Ratio

3. Installing Processor

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well,

you may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

Note: Some CPU fans do not have

sensor pin so they cannot support fan

monitoring.

FAN2 Connector

4. Installing CPU & System Fan

FAN3 Connector

This socket supports Micro-FC-PGA2 package CPU, which is the latest CPU package

developed by Intel. Other forms of CPU package are impossible to be fitted in.

CPUFAN Connector

Willamette

CPU CPU Core

Frequency FSB

Clock System

Bus Ratio

Pentium 4 1.5G 1500MHz 100MHz 400MHz 15x

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.7G 1700MHz 100MHz 400MHz 17x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 1.9G 1900MHz 100MHz 400MHz 19x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

Warning: Intel®845E chipset

supports maximum 400MHz

(100MHz*4) / 533MHz

(133MHz*4) system bus and

66MHz AGP clock; higher

clock setting may cause

serious system damage.

Note: Since the latest

rocessor, Northwood,

would detect the clock

ratio automatically, you

may not be able to

adjust the clock ratio in

BIOS manually.

GND

SENSOR +12V

GND

+12V

SENSOR

GND

+12

SENSO

8. S/PDIF Connector

9. JP28 Keyboard/Mouse Wakeup Select Jumper

7. Dr. LED Connector

Connecting Dr. LED you can easily find the system problems that may occur while

assembling. It can clearly indicate whether the problem is caused from components or

improper installation through the 8 LED lights of Dr. LED on the front panel. That is to say

you can diagnose your system status quickly.

S/PDIF (Sony/Philips Digital Interface) is a latest audio transfer file format that provides

impressive quality through optical fiber and allows you to enjoy digital audio instead o

analog. Normally there are two S/PDIF outputs as shown, one for RCA connector, the

most common one used for consumer audio products, and the other for optical connecto

with a even better audio quality. Through a specific audio cable, you can connect the

S/PDIF connector to a S/PDIF audio module bearing S/PDIF digital output. However, you

must have a S/PDIF supported speaker with S/PDIF digital input to make the most of this

function.

This motherboard provides keyboard / mouse wake-up function. You can use JP28 to

enable or disable this function, which could resume your system from suspend mode with

keyboard or mouse. The factory default setting is set to “Enable”(1-2), and you may

disable this function by setting the jumper to 2-3.

6. Support USB2.0 Ports

This motherboard provides six USB2.0 ports to connect USB devices such as mouse,

keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You

can use proper cables to connect USB devices from PC99 back panel or connect USB2

and USB3 headers to the front panel of chassis.

USB2 and USB3 Connectors

Pin 1

USBPWR0

USB_FP_P0-

USB_FP_P0+

GND

KEY

USBPWR0

USB_FP_P1-

USB_FP_P1+

GND

USB_FP_OC0

1 2

S/PDIF Module

(Optional)

Connecting to

RCA Cable

Connecting to

Optical Cable

Audio

cable

1+5V

SPDIFOUT

GND

NO SPDIFIN

JP28

KB/Mouse Wake-up

Pin1

1 2

5 6

3.3V

GND

S3 Enable

Disable

(Default)

12. Power-on and Load BIOS Setup

10. JP1 Buzzer Enable/Disable Jumper

This motherboard comes with another considerate option that allows you to turn off the

voice from buzzer. You can choose not to be bothered by the warning made from buzzer

when it detects an error in operating system. To disable this function, set JP1 to pin 2-3 to

stop the buzzer from sending out voices.

After you finish jumper settings and connect correct cables, power on and enter the

BIOS Setup. Press <Del> during POST (Power On Self Test). Choose "Load Setup

Defaults" for recommended optimal performance.

13. AOpen Bonus Pack CD

11. Chassis Intrusion Connector

The “CASE OPEN” header provides chassis intrusion-monitoring function. To make this

function works, you have to enable it in the system BIOS, connect this header to a sensor

somewhere on the chassis. So, whenever the sensor is triggered by lights or by the

opening of the chassis, the system will beep to inform you. Please be informed that this

useful function only applies to advanced chassis, you may purchase an extra sensor, attach

it on your chassis, and make a good use of this function.

You can use the autorun menu of Bonus CD. Choose the utility and driver and select model

name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

Pin1

JP1 (Buzzer)

Enable

(Default)

Disable

Enable

(Default)

Disable

AOpen Easy Flash is user-friendlier than traditional flash method. The BIOS binary file and

flash routine are combined together and you simply run a single file to complete the flash

process.

1. Download new BIOS upgrade zipped file fromAOpen's web site. For example,

MX4B533102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com/) which supports miscellaneous

operation systems to extract the binary BIOS file and the flash utility. Or Winzip

(http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, MX4B533102.BIN & MX4B533102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> MX4B533102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup Defaults",

then “Save & Exit Setup” and finish the BIOS upgrade.

This motherboard comes with an Intel®10/100Mbps LAN controller. You can find the LAN

driver from the Bonus Pack CD.

14. Installing LAN Driver

15. Installing Audio Driver 17. BIOS Upgrade

16. Installing USB2.0 Driver

Under Windows XP System

After enabling the USB 2.0, Windows XP setup will show a "Found New Hardware" dialog

box. Under Windows XP, "Universal Serial Bus (USB) Controller" will be displayed.

1. Click "Next," and from the generated list box, choose "Install from a list or special

location (Advanced)", click "Next"

2. Click "Next," and from the generated choices, choose "Include this location in the

search:"

3. Insert the Bonus CD in CD-ROM.

4. Type "[CD-ROM]:\Driver\Intel\USB2.0\WinXP" in the text box that appears.

5. Click "Next."A message informing you that Windows XP has found "Intel PCI to USB

Enhanced Host ControllerA1" should appear.

6. When the New Hardware Wizard has finished installing the USB driver, click "Finish"

This motherboard comes with a RealTek AC97 CODEC. You can find the audio driver from

the Bonus Pack CD auto-run menu.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnPinformation

will be refreshed and you probably need to re-configure your system.

If you encounter any trouble to boot you system, follow the procedures

accordingly to find the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

MX4B-533 R1.02 May 01. 2002 AOpen Inc.

Award Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

MX4B-533 is model name of motherboard; R1.02 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com/tech/download/default.htm

News Group: News posted by computer experts. You are welcome to join

any discussion there.

http://www.aopen.com/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem efficiently and provide important

reference for you if next time you want to buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com/tech/contact/techusa.htm

Japanese http://www.aopen.co.jp/tech/contact/techjp.htm

Chinese http://www.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5399

America

AOpen America Inc.

Tel: 1-408-922-2100

Fax: 1-408-922-2935

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

AOpen Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)有限公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Japan

AOpen Japan Inc.

Tel: 81-048-290-1819

Fax: 81-048-290-1820

Inhaltsverzeichnis

Andere AOpen Hauptplatine Handbücher

AOpen

AOpen AX45 PRO-533 Datenblatt

AOpen

AOpen MX3W Pro Einrichtungshandbuch

AOpen

AOpen MT85 Bedienungsanleitung

AOpen

AOpen VKM400AM-S Bedienungsanleitung

AOpen

AOpen MK77M-V Bedienungsanleitung

AOpen

AOpen I865Gm-7L/7N Bedienungsanleitung

AOpen

AOpen Manual Bedienungsanleitung

AOpen

AOpen MK77 Bedienungsanleitung

AOpen

AOpen AP5T Bedienungsanleitung

AOpen

AOpen AX4SG Max II Bedienungsanleitung

AOpen

AOpen AK77-8X Einrichtungshandbuch

AOpen

AOpen DXPN-U Datenblatt

AOpen

AOpen AX4T II-533 Einrichtungshandbuch

AOpen

AOpen AX63 Einrichtungshandbuch

AOpen

AOpen MX36CE Einrichtungshandbuch

AOpen

AOpen Fortress 1100 Datenblatt

AOpen

AOpen AK79D-400VN Datenblatt

AOpen

AOpen i915Ga-HFS Bedienungsanleitung

AOpen

AOpen Fortress 7000 Bedienungsanleitung

AOpen

AOpen AX37D Pro Einrichtungshandbuch

AOpen

AOpen MK77M-8XN Datenblatt

AOpen

AOpen AK73 Series Einrichtungshandbuch

AOpen

AOpen MX33 Bedienungsanleitung

AOpen

AOpen XC CUBE UX915G Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung