AOR AR-STV Bedienungsanleitung

AR-STV

WIRELESS CAMERA DETECTOR

INSTRUCTION MANUAL

AOR, LTD.

TABLE OF CONTENTS

Table of contents ------------------------------------------------------------------------------------------- 1

1 Index ------------------------------------------------------------------------------------------------ 2

1-1 Introduction -------------------------------------------------------------------------------------- 2

1-2 Maintaining the unit ---------------------------------------------------------------------------- 2

1-3 Power requirements --------------------------------------------------------------------------- 2

1-4 Supplied accessories ------------------------------------------------------------------------- 3

1-5 Features ------------------------------------------------------------------------------------------ 3

2 Control and functions ------------------------------------------------------------------------------ 3

2-1 Front panel controls ---------------------------------------------------------------------------- 3

2-2 Rear Panel --------------------------------------------------------------------------------------- 6

3 Connections -------------------------------------------------------------------------------------------- 6

4 Power Switch ------------------------------------------------------------------------------------------- 6

5 Operations of the AR-STV -------------------------------------------------------------------------- 6

5-1 Display --------------------------------------------------------------------------------------------- 6

5-2 Operation mode --------------------------------------------------------------------------------- 7

5-2-1 Search mode ----------------------------------------------------------------------------------7

5-2-2 Memory mode -------------------------------------------------------------------------------- 10

5-2-3 Setting mode --------------------------------------------------------------------------------- 11

5-3 PC interface -------------------------------------------------------------------------------------- 13

6 Specifications ------------------------------------------------------------------------------------------- 13

7 Limited warranty ---------------------------------------------------------------------------------------- 14

FCC statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must

accept any interference received, including interference that may cause undesired operation.

1 Introduction

1-1Introduction

Thank you for purchasing the AR-STV Wireless Camera Detector.

The AR-STV is a wireless camera receiver with a 2.5 inch color LCD display, steel picture recorder and sensor

that captures analog video signals in real-time. It is mainly designed for use in surveillance applications.

Its built-in clock allows images to be time-stamped and an optional 1 GB SD memory card can be used to store

up to nearly 2000 images.

manual may be copied or transferred by any means without the prior written consent of AOR,

LTD. AOR and the AOR logo are trademarks of AOR, LTD. All other trademarks and names are

acknowledged.

1-2Maintaining the unit

There are no internal operator adjustments. In the unlikely event of service being required,

please contact your dealer for technical assistance.

Level of risk

As the AR-STV operates with a 6 V DC power source, there is little chance of serious injury as long as common

sense is applied.

Observe the polarity of connections if using an external battery charger . DC input is a nominal 6V DC, with the

connector wired center conductor positive. Reverse polarity connection will damage the AR-STV and could lead

to the risk of fire or explosion under severe circumstances.

NEVER connect the AR-STV directly to the AC outlet.

Handling the AR-STV

Use a soft, dry cloth to gently wipe the AR-STV clean. Never use abrasive cleaners or organic

solvents which may damage certain parts. Treat the unit with care, avoid spillage or leakage of

liquids into the cabinet and power supply. Special care should be taken to avoid liquid entering

around the keys, main dial or via the connectors.

[Note: Never push or knock the LCD screen – it is very fragile and sensitive to shock.]

Special remarks

Do not use or leave the AR-STV in direct sunlight (especially the TFT display). It is best to avoid

locations where excessive heat, humidity, dust and vibration are expected. Always keep the

AR-STV free from dust and moisture.

1-3Power requirements

The AR-STV is designed for operation from a nominal 6 V DC (4 AA size alkaline battery or Ni-MH cells). An

external 6V DC power supply (not included), which should be capable of supplying a minimum of 1 amp

continuous may be used to charge the internal Ni-MH cells.

Do not use an external power supply when alkaline battery cells are in the unit.

[ Notice: Always disconnect the external power supply when in use.]

1-4 Supplied accessories

The following accessories are provided in the shipping box.

1 Instruction manual (this booklet)

1 Flexible rubber antenna

1 Belt clip

4 AA size Ni-MH battery cells

1 Battery charger

1-5 Features

zBuilt-in 2.5 inch color LCD display

zBuilt-in clock for time stamp

zStore up to nearly 2000 images with an optional 1 GB SD memory card

zDetect NTSC, PAL, CCIR, EIA or scrambled reverse polarity video signals

zReceives and displays video signals on L-band (1.2 GHz) or S-band (2.4 GHz)

zThe USB connector makes it easy to download stored images into a computer

zEasy to operate with four AA size batteries

zContinuous search between 900 ~ 2800 MHz

z10 search banks

zEasy menu-driven operation

2 Controls and functions

2-1Front panel

The front panel of the AR-STV is dominated by the large color LCD. On the top right corner of the AR-STV, there

is a red LED marked as “STA” (Status). The LED blinks while in the search mode.

Front View

Left View Right View

Right Side of the AR-STV

1 Power ON/OFF switch

Slide the power switch upward to switch on the AR-STV.

To switch off the AR-STV, slide the switch downward.

2 CONT (USB connector)

Using a USB cable (not supplied), connect between the CONT (Control) connector and

a PC to download images.

3 VIDEO (Video Output connector)

This 3.5 mm mono connector provides the composite video output.

An external video monitor may be connected.

4 DC 6V (External power input connector)

To charge the internal Ni-MH cells, connect a 6 V DC charger into this connector. Note

that the center pin of the jack is positive.

5 SD (SD memory card slot)

Insert a SD memory card (up to 4 GB) into this slot to save images.

Approx. 2,000 images may be saved on a 1GB SD card.

Before using a SD memory card, it must be formatted (FAT 32) by a PC.

6 ALM OUT (Alarm output connector)

Connect an external alarm device into this connector. (3.5 mm stereo)

Pin assignment of the connector:

Tip --- Beep output and alarm output

Ring --- Relay output (this pin will make a short circuit to the ground for 2

seconds after a video signal is detected)

(Relay specifications: 50 V DC, 150 mA max. )

Sleeve --- Ground

Left Side of the AR-STV

7 MODE (Mode selector) switch

Press this switch to select the operation mode.

8 REC (Record) switch

Press this switch to store image onto memory.

7 FREQ UP DOWN (Frequency selector switch)

Press this switch upward/downward to change the receive frequency or change search

direction.

2-2Rear panel

8 Belt clip

Attach the supplied belt clip.

9 Battery compartment cover

3 Connections

Connect the supplied flexible rubber antenna to the SMA antenna connector on the top of

the AR-STV.

If required, an external antenna may be connected with a SMA connector for the coaxial cable.

Insert the supplied 4 AA size Ni-MH cells into the battery compartment in the AR-STV.

If not fully charged, connect an external battery charge into the DC 6V connector.

4. Power switch

To switch on the AR-STV, slide the power switch on the right side of the AR-STV upward.

4-1 Start-up

After inserting the batteries, switch on the power switch. The LCD displays search screen

and a STA (Status) LED will blink indicating the AR-STV is in the search mode.

4-2 Powering down

To switch off the AR-STV, slide down the power switch.

4-3 Low Battery

When internal battery voltage becomes low, the Low Battery indicator will appear on the LCD screen. In the

meantime, a beep will sound.

When this message appears on the screen, all operations of the AR-STV will quit

automatically. Immediately switch off the AR-STV, and replace all internal battery cells with

new ones or charge batteries with an external charger.

5 Operations of the AR-STV

5-1 Display

This section explains what you can expect to see on the AR-STV LCD monitor screen.

Once the AR-STV is properly powered up, the display will appear on the screen.

(1) 1G 2G 3G (Hz)

The horizontal axis displays the receive frequency. The AR-STV can receive between

900 MHz ~ 2800 MHz.

(1G indicates 1 GHz in frequency, 2 G for 2 GHz, and 3 G for 3 GHz accordingly.)

(2) V (Video level) N (Noise level)

Video Level

The V (Video) line on the vertical axis displays the video quality threshold level.

Note that video level is NOT related to the signal strength.

Setting the video threshold level higher will display the video signal only with the better

quality.

Setting the video threshold level lower will display the video signal even it has a poor

quality.

Noise Level

The N (Noise) line on the vertical axis displays the signal strength.

Setting the Noise threshold level higher can detect only strong signals.

Setting the Noise threshold level lower can detect any weak signals even it has a poor

quality.

Video Level and Noise level can be adjusted on the Search Bank Setting Menu.

5-2 Operation Mode

There are three (3) operation modes with the AR-STV.

Search Mode

Memory Mode

Setting Mode

5-2-1 Search Mode

This is a default operation mode of the AR-STV. On this mode, the AR-STV will search frequencies

between 900 MHz ~ 2.8 GHz (2800 MHz) continuously until signal is detected.

Once the AR-STV detects the signal, then it will automatically switch the screen to display the received

video signal.

To stop searching, press the FREQ switch inward. Then above screen will appear.

Signal Level Battery Level SD Card inside I Search Mode

Search Bank # Receive frequency

5-2-1-1 Frequency adjustment

To change the receive frequency, press the FREQ. switch upward or downward.

5-2-1-2 Recording image

To record the received image, press and hold the REC switch for 3 seconds.

(Note: To record an image, an optional SD memory card must be installed in the AR-STV. Otherwise,

a beep will sound, and the SD Error message will appear on the LCD screen.)

5-2-1-3 Search Bank setting

To register a search bank, perform the following steps:

1. On the Search Mode screen, press and hold the MODE switch for 3 seconds.

2. The following search bank setting screen will appear.

Search: Search bank number 0 ~ 9

To change the search bank, press the MODE key.

Start: Select the start frequency. (Frequency range: 900 ~ 2800 MHz)

On above example, 09 is highlighted in reverse color and 900 MHz has

been set as the start frequency.

To change the first 2 digits, press the FREQ. switch inward.

The highlighted area will change into green indicating it is ready to

change the parameter.

Press the FREQ. switch upward or downward to select the desired

frequency.

To confirm entry, press the FREQ. switch inward again.

The highlighted area will change into white.

To change the last 2 digits of frequency, press the FREQ. switch downward.

Repeat above steps to change the last 2 digits of frequency.

End: Select the end frequency. (Frequency range: 900 ~ 2800 MHz)

On above example, 2800 is highlighted in reverse color and 2800 MHz has

set as the end frequency.

To change the end frequency, perform the same procedures as the start

frequency entry.

Step: Select the search frequency step. (Entry range: 2 ~ 10 MHz)

To change the parameter, perform the same procedures as the start

frequency entry

Noise Level: Select the noise threshold level.

(Entry range: -30 ~ -80 dbm in 5 dB increments)

Suggested level: 75 (for normal search)

0 (for weak signal)

Run: Select the search bank enable or disable.

To change the parameter, perform the same procedures as the start

frequency entry

Video Level: Select the video threshold level.

Andere Handbücher für AR-STV

Inhaltsverzeichnis

Andere AOR Sicherheitssensor Handbücher

AOR

AOR AR-STV Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung