APsystems DS3D Bedienungsanleitung

1 2022/01/06

Rev1.4 Quick Installation Guide

APsystems Microinverter Quick Installation Guide

APsystems DS3D Microinverter

(For EMEA)

ALTENERGY POWER SYSTEM Inc.

emea.APsystems.com

APsystems

Karspeldreef 8, 1101 CJ, Amsterdam, The Netherlands

Tel: +31 (0)85 3018499 EMAIL: info.emea@APsystems.com

APsystems

Rue des Monts d'Or, ZAC de Folliouses Sud-Les Echets 01700 Miribel, France

TEL: +33-481-65-60-40 EMAIL:info[email protected]

Please scan this QR code to have access

to our APPs and Products information

2 2022/01/06

Rev1.4 Quick Installation Guide

DS3D Microinverter Quick Installation Guide

Step 1. Verify that grid voltage is matching with microinverter rating

Step 2. Y3 AC Bus Cable distribution

a. Each connector drop of the AC Bus cable shall be matching the position of the microinverter.

b. One end of the AC bus cable is used to access the junction box into the power grid.

c. Wire the conductors of the AC bus: L - BROWN; PE - YELLOW GREEN; N - BLUE; (European Standard).

NOTE: Wiring color code can be different according to the local regulation. Check all the wires of the installation before

connecting to the AC bus to be sure they match. Wrong cabling can damage irreparably the microinverters such damage

is not covered by the warranty.

Step 3. Attach the APsystems Microinverters to the Racking

NOTE: Install the microinverters (including DC and AC connectors) under the PV modules to avoid direct exposure to

rain, UV or other harmful weather events. Allow a minimum of 1.5 cm (3/4”) below and above the casing of the

microinverter to allow proper air flow. The racking must be properly grounded as per local electrical code.

ATTENTION: Do NOT carry the microinverter

by the AC cable. This may cause the AC cable to

partially or fully disconnect from the unit,

resulting in no or poor operation.

a. Mark the location of the microinverter on the rack, with respect to the PV module junction box or any other obstructions.

b. Mount one microinverter at each of these locations using hardware recommended by your module racking vendor.

Grounding washer

(Warning injure hand)

Step 4. Ground the system

Y3 AC Bus cable has an embedded PE wire: this might be sufficient to ensure proper grounding of the whole PV array. However

in areas with special grounding requirements, external grounding work may still be needed, using the grounding lug supplied

with the Microinverter.

(Not supplied by

APsystems)

Grounding lug

3 2022/01/06

Rev1.4 Quick Installation Guide

Step 5. Connect the APsystems Microinverter to AC bus cable

Insert the microinverter AC connector into the trunk cable connector. Make sure to hear the “click” as a proof of robust

connection.

Step 6. Install a Bus Cable End Cap at the end of AC bus cable

Step 7. Connect APsystems Microinverters to the PV Modules

NOTE: When plugging in the DC cables, the microinverter should immediately blink green ten times. This will happen

as soon as the DC cables are plugged in and will show that the microinverter is functioning correctly. This entire check

function will start and end within 10 seconds of plugging in the unit, so pay careful attention to these lights when

connecting the DC cables.

WARNING: Double check to make sure all of the AC and DC wiring has been correctly installed. Ensure that none of the

AC and/or DC wires are pinched or damaged. Make sure that all of the junction boxes are properly closed.

WARNING: Each PV panel must be carefully connected to the same channel.

Make sure to not split positive and negative DC cables into two different input channels: microinverter will be damaged

and warranty will not apply.

Click

Best Practice: Use the AC Bus Cable Unlock Tool to disconnect

the connectors.

NOTE: AC connector interface as follows

NOTE: Cover any

unused connectors with Bus Cable Y

CONN to protect the unused connectors

From left to right are:

L-PE-N.

Nut

Seal

Body

3.3

mm~

4 2022/01/06

Rev1.4 Quick Installation Guide

NOTE: Each channel connects 2 PV modules in series (For PV modules with Voc<60V).

The input channel will not work if connects to a single module (Voc<60V).

That means the quantity of PV modules in the system is an even number.

Step 8. Complete the APsystems installation map

a. Each APsystems Microinverter has 2 removable serial number labels.

b. Complete installation map by sticking ID label of each microinverter at the right location.

c. The second serial number label, could be stuck on the solar module frame, which could help later to confirm the position

of the microinverter without dismantling the PV module.

NOTE:

.

The layout of the microinverters' serial numbers installation map is only suitable for typical

installation.

. Installation Map is available in the last page appendix of this manual.

. Use ECU_APP (available in the EMA Manager) to scan the serial numbers on the map when

setting up the ECU (see ECU instruction manual for more info).

Product information is subject to change without notice. (Please download manuals at www.APsystems.com).

Andere Handbücher für DS3D

Inhaltsverzeichnis

Andere APsystems Wechselrichter Handbücher

APsystems

APsystems DS3-M Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems QT2-EU Bedienungsanleitung

APsystems

APsystems YC1000-3 3-Phase Bedienungsanleitung

APsystems

APsystems YC600B Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems YC1000-3-208 Bedienungsanleitung

APsystems

APsystems YC500I-LK Bedienungsanleitung

APsystems

APsystems YC500I-ZA Bedienungsanleitung

APsystems

APsystems YC1000-3 Series Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems QT2D Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems YC500A Bedienungsanleitung

APsystems

APsystems DS3D Bedienungsanleitung

APsystems

APsystems YC1000-3-3 Bedienungsanleitung

APsystems

APsystems QT2-208 Bedienungsanleitung

APsystems

APsystems YC500I-EU Bedienungsanleitung

APsystems

APsystems QS1 Bedienungsanleitung

APsystems

APsystems QS1A Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems QS1-EU Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung