APsystems YC1000-3-EU Bedienungsanleitung

2018/05/28 REV1.7 Quick Installation Guide

YC1000-3-EU 3-Phase Microinverter Quick Installation Guide

The sketch of YC1000-3 support system.

All the solar panels are placed into two lines. Then put a YC1000-3 in the middle of the two lines and make

sure it is easy to connect with to four panels which are next to it, as well all the cables.

Step 1. Verify the grid voltage to match with microinverter rating.

Step 2. Lay the AC bus according to the arrangement of APsystems Microinverter.

Step 3. Attach the APsystems Microinverters to the racking.

NOTE: Do not place the inverters (including DC and AC connectors) where exposed to the sun, rain or snow,

even gap between modules. Allow a minimum of 3/4’’(1.5cm.) between the roof and the bottom of the

Microinverter to allow proper air flow.

Step 4. Connect the APsystems Microinverter cables to the AC bus cable.

NOTE: AC connector interface as follows, NOTE: Cover all unused T connectors with

from left to right PE, N, L3, L2, L1. Bus Cable End Cap to protect the T connectors.

Please scan the QR code to get

mobile app and more support

to help the installation.

Click

2018/05/28 REV1.7 Quick Installation Guide

Step 5. Place the PV modules and connect each YC1000 to four PV modules close-by.

CH4 CH3 CH2 CH1

Step 6. Install a protective end cap at the end of AC bus cable.

a．Wire stripping

b．Set the parts on the cable.

c．Insert five wires into the core wires hole of the

body.

d．Insert seal and Clamp Finger into the

body ,then tighten the nut, torque 2.5±0.5NM.

Step 7. Install the AC branch circuit junction box.

Step 8. Connect the cables to the branch junction box.

a. Put the unused end of the AC interconnector cable into the branch junction box.

b. Place cable connecting to the point of load interconnection into the branch junction box.

c. Wire the conductors of the AC bus: BROWN-L1; BLACK -L2; GRAY-L3; LIGHT BLUE-N;

YELLOW GREEN-PE.

NOTE: Wiring colour code can be different according local regulation, check all the wires of the installation

before connecting to the AC bus to be sure they match.

Wrong cabling can damage irreparably the microinverters, such an issue is not covered by the warranty.

NOTE: Using apsystems' mobile app ArrayApp can make the installation and registion much more simple.

Step 9. Complete the APsystems installation map.

Each APsystems microinverter has two removable serial number labels. Peel labels off, affix one to the

respective location on the APsystems installation map, and affix another to the PV module frame which is

easy to see. Use the Scanning Gun to scan the serial numbers on the map into the computer or scan by

mobile phone with APsystems ArrayApp, then complete the setting (see ECU manual).

NOTE: Step 1~9 can change sequence for convenience of installation.

Step 10. Start the operation.

1. Turn on the AC circuit breaker on each microinverter AC branch circuit.

2. Turn on the main utility-grid AC circuit breaker. Your system will start producing power after a

five-minute waiting time.

Product information is subject to change without notice.

(Please download manuals at www.APsystems.com).

Inhaltsverzeichnis

Andere APsystems Wechselrichter Handbücher

APsystems

APsystems QS1-EU Bedienungsanleitung

APsystems

APsystems EZ1 Series Bedienungsanleitung

APsystems

APsystems YC500A Bedienungsanleitung

APsystems

APsystems YC500A Bedienungsanleitung

APsystems

APsystems DS3-M Bedienungsanleitung

APsystems

APsystems QT2-220 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems YC500A Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems YC1000-3-NA Bedienungsanleitung

APsystems

APsystems QT2D Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems DS3D Bedienungsanleitung

APsystems

APsystems DS3D-AU Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems QT2 Bedienungsanleitung

APsystems

APsystems YC1000-3 Series Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems DS3 Series Bedienungsanleitung

APsystems

APsystems YC600 Bedienungsanleitung

APsystems

APsystems YC1000-3-208 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung