APW Wyott FD-18H Bedienungsanleitung

Phone:

Fax: (214) 565-0976

Toll Free: (800) 527-2100

Website: www.apwwyott.com

E-mail: [email protected]

(214) 421-7366

INSTALLATION

AND

OPERATING

INSTRUCTIONS

INTENDED FOR OTHER THAN HOUSEHOLD USE

Models: FD, FDD, FDL & FDDL

RETAIN THIS MANUAL FOR FUTURE REFERENCE

UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

P/N 70400000 Rev. 3/06

OVERHEAD WARMERS

APW WYOTT

729 Third Avenue

Dallas, TX 75226

This equipment has been engineered to provide you with year-round dependable service when used

according to the instructions in this manual and standard commercial kitchen practices.

Initial heating of unit may generate smoke or fumes and must be done in a well ventilated area.

Overexposure to smoke or fumes may cause nausea or dizziness.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance. !!

WARNING: Improper installation, adjustment, alteration, service or maintenance can

cause property damage, injury or death. Read the Installation, Operating and

Maintenance Instructions thoroughly before installing or servicing this equipment. !!

ANSI/NSF4

SECTION

ITEM

Owner’s Information

Important Safety Information

Specifications

Operation

Cleaning

Troubleshooting

Wiring Diagrams

Parts Lists

Warranty

General Information

Installation Instructions

General Operation Instructions

Warranty Information

Electrical

Dimensions

Operating Instructions

General Cleaning Instructions

FD Wiring Diagrams

FDL Wiring Diagrams

FDD Wiring Diagrams

FDDL Wiring Diagrams

FD Replacement Parts

FDL Replacement Parts

FDD or FDDL Replacement Parts

PAGE

TABLE OF CONTENTS

1. OWNERS INFORMATION

General Information:

5. APW Wyott Overhead Foodwarmers are constructed from high quality stainless steel and available

in lengths from 18" to 96”. Utilizing a metal sheath-heating element with a specially designed reflector,

these units give uniform heat over the entire holding surface.

6. In Europe, contact anAPW Wyott authorized service agency for replacement light bulbs.

A. Always clean equipment thoroughly before first use (See cleaning instructions).

B. Provide the following clearances around foodwarmer:

1. Always clean equipment thoroughly before first use. (See general cleaning instructions).

2. Check rating label for your model designation and electrical rating.

3. For best results, use stainless steel countertops.

4. All dimensions in parenthesis in centimeters unless noted.

Installation Instructions:

C. Consult foodwarmer rating label for model designation and correct operating voltage and amperage.

D. Ceiling mounting brackets are provided with each foodwarmer for chain or shelf mounting. Remove

brackets form packaging and screws from ends of foodwarmer to attach brackets. Use four #10 screws

or studs with locknuts for shelf mounting. For chain mounting, use #14 jack chain and “S” hooks.

E. Remote switches are recommended. Longer switch life will result from cooler switch mounting

locations. Optional stainless steel remote toggle and infinite switch box kits are available. Installation

of remote switch box by service personnel requires 7/8" conduit, 1/4" push-on terminals, and no. 14

AWG copper wire suitable for at lest 90ºC. Mount remote box to flat surface with two #10 screws or

studs with locknuts. All wires marked as shown on wiring diagram.

F. Optional tubular stands are available for permanently mounting foodwarmers to non-combustible

countertops.

G. Optional portable legs are available for foodwarmers for use over non-combustible countertops.

H. Installation of cord sets by service personnel should utilize the strain relief, grounding stud, and

porcelain wire nuts provided with foodwarmers.

I. If unit is supplied with a power cord, the appliance must be positioned so that the plug is accessible.

NOTE: TO AVOID BURNING OR CHARRING OF MATERIALS IN THE SURFACE

BELOW THE FOODWARMER USE ONLY ABOVE AN ALL-METAL STRUCTURE

SUCHAS ATABLE OR COUNTERTOP. SEE MINIMUM CLEARANCE CHARTABOVE.

REMOTE SWITCHES ARE RECOMMENDED FOR UNDER SHELF MOUNTING.

LONGER SWITCH LIFE WILL RESULT FROM COOLER SWITCH MOUNTING

LOCATIONS.

Do not install A = Minimum clearance (in inches) to

Bottom Surface of unit from Tabletop

closer than:

= Minimum clearance (in inches) to

Back of unit

Sides of unit.

FDD/FDDL-18

FDD/FDDL-24

FDD/FDDL-30

FDD/FDDL-36

FDD/FDDL-42

FDD/FDDL-48

FDD/FDDL-54

FDD/FDDL-60

FDD/FDDL-66

FDD/FDDL-72

FDD/FDDL-84

FDD/FDDL-96

FD/FDL-18

FD/FDL-24

FD/FDL-30

FD/FDL-36

FD/FDL-42

FD/FDL-48

FD/FDL-54

FD/FDL-60

FD/FDL-66

FD/FDL-72

FD/FDL-84

FD/FDL-96

N/A

MODEL A B C A B C

HIGH WATTAGE LOW WATTAGE

CLEARANCES FOR OVERHEADS

General Operation Instructions:

Warranty Information:

Reliability Backed By APW Wyott’s Warranty:

Service Information:

Electrical:

1. All foodservice equipment should be operated by trained personnel.

2. Do not allow your customers to come in contact with any surface labeled “CAUTION HOT”.

3. Never hold food below 150°F (66°C).

All APW Wyott Overhead Warmers are backed by a one year parts and labor warranty, including On-Site

Service calls within 50 miles of authorized service technicians.

Service Hotline (800) 733-2203

APW Wyott Overhead Warmers are designed, built and sold for commercial use and should be operated by

trained personnel only. Clearly post all CAUTIONS, WARNINGS and OPERATING INSTRUCTIONS near

each unit to insure proper operation and to reduce the chance of personal injury and/or equipment damage.

Always disconnect power before servicing the Overhead Warmer. Surfaces will remain hot after power has

been turned off. Allow unit to cool before cleaning or servicing. Never clean the Overhead Warmer by

immersing it in water. The Overhead Warmer is not protected against water jets; DO NOT CLEAN

OVERHEAD WARMER WITHA WATER JET.Always clean equipment before first use.

If the supply cord is damaged, an authorized service agent or a similarly qualified person must replace it to

avoid a hazard or voiding the warranty.

2. SAFETY INFORMATION

3. SPECIFICATIONS

A. Single-phase operation at 120, 208, 230, and 240 volts. (See label on each unit).

B. Field-wired units provided with 7/8" conduit hole, 6" long leads, and porcelain wire nuts. For supply

connections, use minimum no. 14AWG copper wires suitable for at least 90ºC.

C. U.S. cord-connected units provided with following plug configuration:

1. 120 volt up to 1440 watts = NEMA5-15P; 120 volt up to 1920 watts = NEMA5-20P

2. 208 volt up to 2496 watts = NEMA6-15P; 208 volt up to 3328 watts = NEMA6-20P

3. 240 volt up to 2880 watts = NEMA6-15P; 240 volt up to 3840 watts = NEMA6-20P

D European cord-connected units provided with following plug configuration:

1. Continental Europe230 volt up to 3600 watts = Schuko CEE7/7

2. UK230 volt up to 2930 watts = Bs1363

Overall Dimensions:

.875 [ 2.22 ] CONDUIT HOLE

POWER LEADS

6.923

[ 17.58]

6.000

[ 15.24 ]

PILOT LIGHT TOGGLE OR INFINITE SWITCH

RATING LABEL

OVERHEAD WARMER LENGTH

18.00 [45.72] TO 72.00 [182.88] .75

[1.91]

3.58

[9.09]

MOUNTING BRACKETS

1.00

[2.55]

FD MODELS

9.125

[ 23.18]

10.048

[ 25.52 ]

FDL MODELS

15.125

[ 38.42 ]

16.971

[ 43.11]

FDD, FDDL MODELS

FOR INSTALLATION ABOVE NONCOMBUSTIBLE SURFACE

5/16 -18 STUD MOUNT

1.00[2.54] SQUARE

S/S TUBING 16.00

[40.64]

OVERHEAD WARMER LENGTH + 1.06[2.7]

18.50

[ 46.99 46.99

]

TUBULAR STAND KIT

FOR USE ABOVE NONCOMBUSTIBLE SURFACE

1.00[2.54] SQUARE

S/S TUBING

11.27[28.63]

11.00 [27.94]

16.00 [

40.64 ]

18.50

[]

OVERHEAD WARMER LENGTH + 2.06[5.23]

PORTABLE LEG KIT

WARNING: ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE

INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR

DEATH.

Electrical Ground is required on this appliance.

Do not modify the power supply cord plug. If it does not fit into the outlet, have

the proper outlet installed by a qualified electrician

Do not use an extension cord with this appliance.

Check with a qualified electrician if you are unsure as to whether the appliance

is properly grounded.

4. Operation

5. Cleaning

6. Troubleshooting

A. All foodservice equipment should be operated by trained personnel.

B. Do not allow your customers to come in contact with any surface labeled “CAUTION HOT”.

C. Switch on unit. Place precooked product under heat source. Maximum heat coverage equivalent to

unit length.

D. Never hold food below 150ºF.

A. Never clean any electrical unit by immersing it in water.

B. Never clean any electrical unit using water jets.

C. Disconnect power before cleaning or servicing units.

D. Clean unit daily. Use warm, soapy water. Mild cleansers and non-abrasive pads may be used to

remove baked-on food.

A. Always ask and check:

1. Is the unit connected to a live power source?

2. Check the circuit breaker.

3. Is the power switch on and pilot light illuminating?

4. Check the rating label. Is the unit operating on proper voltage?

B. If the above checks out, and problems still exist, call an APW Wyott authorized service agency.

C. All service should be performed by an APW Wyott authorized service agency.

General Cleaning Instructions:

Turn off before surface cleaning.

All service should be performed by an APW

authorized service agency.

BLUE

ELEMENT

GL1L

BROWN

LIGHT

PILOT

TOGGLE

SWITCH

GREEN

BROWN

200-240V: BLUE

120V: WHITE

GREEN

ELEMENT

200-240V: BLUE

BROWN

120V: WHITE

REMOTE CONFIGURATION

FD18-72 WIRING DIAGRAM

INFINITE CONTROL CONFIGURATION

TOGGLE SWITCH CONFIGURATION

BLUE

GREEN

PILOT

LIGHT

ELEMENT

L1 L2

BROWN

120V: WHITE

BROWN

CONTROL

INFINITE PL1L

H1 H2

200-240V: BLUE

INDICATOR LIGHT

HEATING ELEMENT

DISPLAY LIGHT

PILOT

EGO

INFINITE

CONTROL

67177 REV-11/2001

7. WIRING DIAGRAMS

GREEN

WHITE BLACK

36,42,48,54 MODELS

TWO LAMPHOLDERSONE LAMPHOLDER

18,24,30 MODELS

ELEMENT

200-240V: BLUE

BROWN

120V: WHITE

BROWN

WHITE BLACK

BLUE

200-240V: BLUE

120V: WHITE

N/L2

LABELS

WHITE BLACK

THREE LAMPHOLDERS

60,66,72 MODELS

WHITE BLACK

FOUR LAMPHOLDERS

84,96 MODELS

BLUE

BROWN

BLUE

BROWN

200-240V: BLUE

BROWN

N/L2

GREEN WHITE BLACK WHITE

36,42,48,54 MODELS

TWO LAMPHOLDERSONE LAMPHOLDER

18,24,30 MODELS

ELEMENT

TOGGLE

SWITCH

LIGHT

PILOT

2 3

BLACK

5 4

120V: WHITE

BLUE

LABELS

BLACK

60,66,72 MODELS

THREE LAMPHOLDERS

WHITE

BLUE

BLACK

84,96 MODELS

FOUR LAMPHOLDERS

WHITE

BLUE

REMOTE CONFIGURATION

FDL18-72 WIRING DIAGRAM

INFINITE CONTROL CONFIGURATION

TOGGLE SWITCH CONFIGURATION

GREEN

BROWN

200-240: BLUE

N/L2

BROWN

BLUE

BROWN

WHITE BLACK WHITE BLACK

ELEMENT

36,42,48,54 MODELS

TWO LAMPHOLDERSONE LAMPHOLDER

18,24,30 MODELS

CONTROL

INFINITE PL1L2

H1 H2 PILOT

LIGHT

120V: WHITE

5 4

BLUE BLUE BLUE

LABELS

BLACKWHITE

FOUR LAMPHOLDERS

84,96 MODELS

BLACK

WHITE

THREE LAMPHOLDERS

60,66,72 MODELS

BLUE

9 9

INDICATOR LIGHT

HEATING ELEMENT

DISPLAY LIGHT

PILOT

H2 EGO

INFINITE

CONTROL

REMOTE CONFIGURATION

FDD18-72 WIRING DIAGRAM

INFINITE CONTROL CONFIGURATION

TOGGLE SWITCH CONFIGURATION

GREEN

200-240V: BLUE

ELEMENT

BROWN

120V: WHITE

N/L2

ELEMENT

200-240V: BLUE

120V: WHITE

BROWN

N/L2

LABELS

200-240V: BLUE

120V: WHITE

BROWN

GREEN

N/L2

PILOT

LIGHT

PILOT

LIGHT

BLUE

BROWN

ELEMENT

PL1 L2

H1 H2

PL1 L2

H1 H2

INDICATOR LIGHT

HEATING ELEMENT

DISPLAY LIGHT

PILOT

H2 EGO

INFINITE

CONTROL

LABELS

REMOTE CONFIGURATION

FDDL18-72 WIRING DIAGRAM

INFINITE CONTROL CONFIGURATION

TOGGLE SWITCH CONFIGURATION

LABELS

N/L2

120V: WHITE

200-240: BLUE

120V: WHITE

200-240: BLUE

120V: WHITE

200-240: BLUE

BROWN

GREEN

1 LAMPHOLDER 2 LAMPHOLDERS 3 LAMPHOLDERS 4 LAMPHOLDERS

18,24,30 MDLS 36,42,48,54 MDLS 60,66,72 MDLS 84,96 MDLS

ELEMENT

WHITE WHITE WHITE WHITE

BLACK BLACK BLACK BLACK

BLUE BLUE BLUE

INDICATOR LIGHT

HEATING ELEMENT

DISPLAY LIGHT

PILOT

H2 EGO

INFINITE

CONTROL

BROWN

ELEMENT

BLUE

BROWN

ELEMENT

BLUE

PILOT

LIGHT

PILOT

LIGHT

INFINITE

CONTROL

INFINITE

CONTROL

PL1 L2

H1 H2

PL1 L2

H1 H2

LABELS

N/L2

120V: WHITE

200-240: BLUE

BROWN

GREEN

G1 LAMPHOLDER

18,24,30 MDLS

2 LAMPHOLDERS

36,42,48,54 MDLS 3 LAMPHOLDERS

84 MDL

3 LAMPHOLDERS

60,66,72 MDLS

WHITE WHITE WHITE WHITE

BLACK BLACK BLACK BLACK

BLUE BLUE BLUE BLUE

PILOT

LIGHT

PILOT

LIGHT

LABELS

N/L2

120V: WHITE

200-240: BLUE

BROWN

GREEN

G1 LAMPHOLDER

18,24,30 MDLS

2 LAMPHOLDERS

36,42,48,54 MDLS 4 LAMPHOLDERS

84,96 MDL

3 LAMPHOLDERS

60,66,72 MDLS

TOGGLE

SWITCH

TOGGLE

SWITCH

BROWN BROWN

BROWN

BLUE

BLUE BLUE BLUE

ELEMENT

WHITE WHITE WHITE WHITE BLACK

BLACK

67179 REV-7/00

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere APW Wyott Speisenwärmer Handbücher

APW Wyott

APW Wyott DW-1A Bedienungsanleitung

APW Wyott

APW Wyott CW-3A Bedienungsanleitung

APW Wyott

APW Wyott Porta-Stove CHP-1A Bedienungsanleitung

APW Wyott

APW Wyott CH-11D Bedienungsanleitung

APW Wyott

APW Wyott HFW-43 Bedienungsanleitung

APW Wyott

APW Wyott DWC-13-1 Bedienungsanleitung

APW Wyott

APW Wyott IP30-rated L2+ W-3Vi Bedienungsanleitung

APW Wyott

APW Wyott SM-50-11 Bedienungsanleitung

APW Wyott

APW Wyott BW-20 Bedienungsanleitung

APW Wyott

APW Wyott CCW Bedienungsanleitung

APW Wyott

APW Wyott HFW-1 Bedienungsanleitung

APW Wyott

APW Wyott FD Bedienungsanleitung

APW Wyott

APW Wyott W-3V Bedienungsanleitung

APW Wyott

APW Wyott OVERHEAD WARMERS FD Bedienungsanleitung

APW Wyott

APW Wyott Cooker / Warmer Merchandising Systems CWM-2A Bedienungsanleitung

APW Wyott

APW Wyott Radiant Black FDB-18 Bedienungsanleitung

APW Wyott

APW Wyott SHFWEZ-1 Bedienungsanleitung

APW Wyott

APW Wyott C-Radiant FDDC-18H Bedienungsanleitung

APW Wyott

APW Wyott SM-50-4ULS Bedienungsanleitung

APW Wyott

APW Wyott Classic RCW - 7 Bedienungsanleitung

APW Wyott

APW Wyott DWC13-N Bedienungsanleitung

APW Wyott

APW Wyott BM-30 Bedienungsanleitung

APW Wyott

APW Wyott FDD-18 Bedienungsanleitung

APW Wyott

APW Wyott FD Bedienungsanleitung

Beliebte Speisenwärmer Handbücher anderer Marken

ARREDO

ARREDO Illusion 1000 Bedienungsanleitung

Vollrath

Vollrath Mirage 74701DW Bedienungsanleitung

Moffat

Moffat BKRW3 Service-Handbuch

Hupfer

Hupfer SPTW-2/EBF Bedienungsanleitung

Kontour

Kontour K1043E Bedienungsanleitung

Hatco

Hatco Glo-Ray GRMW-3 Anwendungshandbuch

HATO

HATO Macho Nacho FST-1-MN Bedienungsanleitung

Wittco

Wittco 500-CW Bedienungsanleitung

Wells

Wells SS-276ULT Bedienungsanleitung

Kerbl

Kerbl FastHeat Bedienungsanleitung

Johnson

Johnson Kaldino Bedienungsanleitung

Wells

Wells BMW206ULRTD/AF Bedienungsanleitung

KRATOS

KRATOS 29М-008 Bedienungsanleitung

Wells

Wells M227 Series Bedienungsanleitung

Henny Penny

Henny Penny HCS-2 Bedienungsanleitung

Amba

Amba RADIANT RSWH-P Bedienungsanleitung

Homecraft

Homecraft BS15BS Bedienungsanleitung

Hatco

Hatco PW Series Bedienungsanleitung