APW Wyott WS-2 Bedienungsanleitung

Phone: +1

Fax: +1 (307) 637-8071

Toll Free: +1 (800) 752-0863

Website: www.apwwyott.com

E-mail: [email protected]

(307) 634-5801

INSTALLATION

AND

OPERATING

INSTRUCTIONS

INTENDED FOR OTHER THAN HOUSEHOLD USE

Models: WS-2, WS-3, WS-4, WS-5, WS-6

RETAIN THIS MANUAL FOR FUTURE REFERENCE

UNIT MUST BE KEPT CLEAR OF COMBUSTIBLES AT ALL TIMES

P/N 8806100 Rev. 9/05

WARMING SHELVES

APW WYOTT

P.O. Box 1829

Cheyenne, WY 82003

This equipment has been engineered to provide you with year-round dependable service when used

according to the instructions in this manual and standard commercial kitchen practices.

WARNING: Improper installation, adjustment, alteration, service or maintenance can

cause property damage, injury or death. Read the Installation, Operating and

Maintenance Instructions thoroughly before installing or servicing this equipment. !!

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain this manual for the life of the equipment. For

Warranty Service and/or Parts, this information is required.

Model Number Serial Number Date Purchased

takes pride in the design and quality of our products. When used as intended and with proper

care and maintenance, you will experience years of reliable operation from this equipment. To ensure best

results, it is important that you read and follow the instructions in this manual carefully.

Installation and start-up should be performed by a qualified installer who thoroughly read, understands and

follows these instruction.

If you have questions concerning the installation, operation, maintenance or service of this product, write

Technical Service Department APW/Wyott Foodservice Equipment Company, P.O. Box 1829, Cheyenne,

WY 82003.

Before installing and operating this equipment be sure everyone involved in its operation are fully trained

and are aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules

and precautions.

The following words and symbols, found in this manual, alert you to hazards to the operator, service

personnel or the equipment. The words are defined as follows:

APW Wyott

SAFETY PRECAUTIONS

WARNING:

This symbol refers to a potential hazard or unsafe practice, which could result in

seriousinjuryordeath.

DANGER:

Thissymbolwarnsofimminenthazardwhichwillresultinseriousinjuryor death.

CAUTION:

This symbolrefers to a potentialhazard or unsafe practice,which may resultin minor or

moderateinjuryor productor propertydamage.

NOTICE:

This symbol refers to informationthat needs special attention or must be fully understood

eventhoughnot dangerous.

CAUTION:

These models are designed, built, and sold for commercial use. If these models are

positioned so the general public can use the equipment make sure that cautions, warnings, and

operating instructions are clearly posted near each unit so that anyone using the equipment will

useit correctlyandnotinjurethemselvesor harm the equipment.

WARNING:

Check the data plate on this unit before installation. Connectthe unit only to the voltage

andfrequencylistedon the dataplate.Connectonly to 1or 3 phaseaslistedonthedataplate.

WARNING:

Electrical and grounding connections must comply with the applicable portions of the

nationalelectricalcodeand/orotherlocal electricalcodes.

WARNING:

Disconnect device from electrical power supply and place a Tag Out-Lockout on the

powerplug,indicatingthatyouare workingonthe circuit.

WARNING:

Install per the spacing requirements listed in the installation section of this manual. We

strongly recommend having a competent professional install the equipment.A licensed electrician

should make the electrical connections and connect power to the unit. Local codes should always

be used when connecting these units to electrical power. In the absence of local codes, use the

latestversionof theNationalElectricalCode.

WARNING:

Never clean any electrical unit by immersing it in water. Turn off before cleaning

surface.

WARNING: -

SHOCK HAZARD

De-energize all power to equipment before cleaning the

equipment.

NOTICE:

Local codes regarding installation vary greatly from one area to another. The National

Fire ProtectionAssociation, Inc. states in its NFPA96 latest edition that local codes are Authority

Having Jurisdiction when it comes to requirement for installation of equipment. Therefore,

installationshouldcomplywithalllocalcodes.

IMMEDIATELY INSPECT FOR SHIPPING DAMAGE

All containers should be examined for damage before and during unloading. The freight carrier has

assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent

or concealed, a claim must be made with the delivering carrier.

A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed

by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can

supply the necessary forms.

B) Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection

must be made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all

contents and packaging material.

Installation and start-up should be performed by a qualified installer who thoroughly read, understands and

follows these instructions.

LOCATION OF DATA PLATE

The data plate for the warming shelf is located on the back of the unit by the power cord.

WARNING: This appliance must be serviced by an Authorized Service Technician only.

Disconnectthepowersupplybefore cleaningorservicingthe oven

Regular and thorough cleaning will help to keep the ovens operating properly. If service is

required, contact an Authorized Service Agency, your dealer or the factory to obtain a qualified

technician for the required maintenance/service.

WARNING:

An earthing cable must connect the appliance to all other units in the complete

installationand from thereto an independentearthconnection.

NOTICE:

The unit when installed, must be electrically grounded and comply with local codes, or in

the absence of local codes, with the national electrical code ANSI/NFPA70- latest edition.

Canadian installation must comply with CSA-STANDARD C.22.2 Number 0 M1982 General

Requirements-CanadianElectricalCodePartII, 109-M1981-CommercialCookingAppliances.

CONTENTS

Safety Precautions 2

Specifications 4

Installation 4

Electrical Connections 5

Operating Instructions 5

Maintenance 5

General Troubleshooting 6

Wiring Diagram 6

Parts Lists & Exploded View 7

Warranty 11

SPECIFICATIONS

DOMESTIC MODELS

EXPORT MODELS

MODEL DESCRIPTION ELECTRICAL DIMENSIONS

WS-2 24” surface 120V, 200W, 1.7 Amps 2 3/8”Hx18”Wx24”L

WS-3 36” surface 120V, 300W, 2.5 Amps 2 3/8”Hx18”Wx36”L

WS-4 48” surface 120V, 400W, 3.3 Amps 2 3/8”Hx18”Wx48”L

WS-5 60” surface 120V, 500W, 4.2 Amps 2 3/8”Hx18”Wx60”L

WS-6 72” surface 120V, 600W, 5.0 Amps 2 3/8”Hx18”Wx72”L

WS-2 24” surface 220v, 200W, .9 Amps 2 3/8”Hx18”Wx24”L

WS-3 36” surface 220V, 300W, 1.3 Amps 2 3/8”Hx18”Wx36”L

WS-4 48” surface 220V, 400W, 1.8 Amps 2 3/8”Hx18”Wx48”L

WS-5 60” surface 220V, 500W, 2.2 Amps 2 3/8”Hx18”Wx60”L

WS-6 72” surface 220V, 600W, 2.7 Amps 2 3/8”Hx18”Wx72”L

MODEL DESCRIPTION ELECTRICAL DIMENSIONS

WARNING:

This product is intended for commercial use only. Not for household use Retain this

manualfor futurereferenceOvenmustbekeptclearof combustiblesat all times

CAUTION:

These models are designed, built, and sold for commercial use. If these models are

positioned so the general public can use the equipment make sure that cautions, warnings, and

operating instructions are clearly posted near each unit so that anyone using the equipment will

useit correctlyandnotinjurethemselvesor harm the equipment.

WARNING: -

SHOCKHAZARD

Donotopenanypanelsthat require the use of tools.

WARNING:

This unit is not intended to hold potentially hazardous foods such as un-cooked or un-

preservrdmeatsandsausages.

WARNING: Improper installation, adjustment, alteration, service or maintenance can

cause property damage, injury or death. Read the Installation, Operating and

Maintenance Instructions thoroughly before installing or servicing this equipment. !!

INSTALLATION

The warming shelf has been inspected and tested at the factory prior to shipment.

Unpack the warming shelf and remove all packing materials. Place it on a flat, horizontal surface at the

desired location.

Clean the unit before using. Wipe body and the inside of the unit with a hot, wet cloth to remove any shipping

dust or protective oil.

At 120 volts, this unit draws up to 5 amperes. If connected to a circuit loaded down with too many

other appliances, the fuse will blow out or the circuit breaker will trip, or a reduction in performance will be

experienced.

All food service equipment should be operated by trained personnel.

Never hold food below 150°F or above 40°F.

NOTE:

ELECTRICAL CONNECTIONS

OPERATING INSTRUCTIONS

MAINTENANCE

Check the data plate to determine for which voltage this unit is wired and what voltage service is to use.

These units have been provided with the appropriate cord and plug set. Do not attempt to defeat its purpose

by substituting a plug with different configuration.

When installed, the plug for this unit should be accessible.

1. Switch power to on. NOTE: auxiliary outlet will be energized at this time.

2. Adjust heater to a setting of 7 1/2.

3. Allow 20-30 minutes for unit to come up to temperature. Surface temperature of the shelf will be

between 180°F and 190°F. If too hot or too cool, adjust knob to a better setting for the product.

Higher numbers are hotter and lower numbers are cooler.

Once a week, or more often if necessary, clean the warming shelf thoroughly. Turn off the warming shelf

and allow it to cool.

STAINLESS STEEL: To remove normal dirt or product residue from stainless steel, use ordinary soap and

water (with or without detergent) applied with a sponge or cloth. Dry thoroughly with a clean cloth. Never

use vinegar or corrosive cleaner. Do not use chorine based cleaners.

To remove grease and food splatter or condensed vapors that have hardened on the equipment, apply

cleaners to a damp cloth or sponge and rub cleanser on the metal in the direction of the polished lines on the

metal. Rubbing cleanser as gently as possible in the direction of the polished lines will not mar the finish of

the stainless steel. NEVER RUB WITH A CIRCULAR MOTION. Soil and burned on deposits which do not

respond to the above procedure can usually be removed by rubbing the surface with SCOTCH-BRITE

scouring pads or STAINLESS scouring pads.

a wire brush, steel or abrasive scouring pads (except stainless), scraper, file or other steel

tools. Surfaces which are marred collect dirt more rapidly and become more difficult to clean. Marring also

increases the possibility of corrosive attack.

use any corrosive cleaner. Use only cleaners approved for stainless steel.

use cleaning solvents with a hydrocarbon base.

NEVER USE

NEVER

CAUTION:

Check the data plate on this unit before installation. Connect the unit only to the voltage

andfrequencylistedon the dataplate.Connectonly to 1-or 3-phaseaslistedon the dataplate.

CAUTION:

Ifthe powercordis damaged,replaceonly with an identicalpowercord.

WARNING:

Improper grounding could result in electrical shock. This appliance is equipped with a

three-prong (grounded plug) for your protection against shock hazard and should be plugged

directly into a properlygroundedthree-prongreceptacle. Do not cut or removethe grounding prong

fromthisplug.

WARNING:

Never clean any electrical unit by immersing it in water. Turn off before cleaning

surface.

CAUTION:

Do not useordinary steel woolas any particles left on the surface will rust.

WARNING: -

SHOCK HAZARD

De-energize all power to equipment before cleaning the

equipment.

GENERAL TROUBLESHOOTING

WIRING DIAGRAM

If the unit fails to operate, check the following.

1. Make sure the unit is connected to a live power source.

2. Check the circuit breaker to be sure it has not been tripped.

3. Check if the power switch is on and the indicator light is glowing.

4. Check the data plate and make sure the unit is operating on the proper voltage.

If the above checks out and you still have problems, call an APW Wyott Foodservice authorized service

agency.

E: Service work should be performed only by a qualified technician who is experienced in and

knowledge-able with the operation of commercial gas, electric, steam cooking equipment. Contact the

Authorized Service Agency for reliable service, dependable advice or other assistance and for genuine

factory parts.

Warranty will be void and the manufacturer is relieved of all liability if:

A. Service work is performed by other than an APW Wyott Foodservice authorized Service

Agency; or

B. Other than GenuineAPW Wyott Foodservice replacement parts are installed.

A current listing of all authorized APW Wyott Foodservice authorized parts/service distributors is included

with this product manual at the time of shipment. In the absence of this list, you can call the APW Wyott 24-

hour Service Hot Line which gives access to the nearest Authorized APW Wyott parts/service distributor.

Call 1-800-733-2203.

NOTIC

Wire Diagram

Use with E.G.O. Infinite Switch

ROPE HEATER

Black

White

Green

Power

Cord

Infinite

Switch

Pilot Pilot

Light

H1 H2

7.000

12.500

ROPE HEATER

Routing Pattern

24" 1 8705610 KNOB 24" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1514000 INDICATOR LIGHT

3 1532500 78" CORD SET 16/3 AWG 3 1506600 78" CORD SET, EUR

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1327900 INFINITE SWITCH 5 1327310 INFINITE SWITCH

6 1431101 HEAT CABLE, 60", 120V 6 1431125 HEAT CABLE, 60", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

36" 1 8705610 KNOB 36" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1514000 INDICATOR LIGHT

3 1532500 78" CORD SET 16/3 AWG 3 1506600 78" CORD SET, EUR

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1327900 INFINITE SWITCH 5 1327310 INFINITE SWITCH

6 1431102 HEAT CABLE, 84", 120V 6 1431126 HEAT CABLE, 84", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

48" 1 8705610 KNOB 48" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1514000 INDICATOR LIGHT

3 1532500 78" CORD SET 16/3 AWG 3 1506600 78" CORD SET, EUR

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1327900 INFINITE SWITCH 5 1327310 INFINITE SWITCH

6 1431105 HEAT CABLE, 108", 120V 6 1431129 HEAT CABLE, 108", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

60" 1 8705610 KNOB 60" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1514000 INDICATOR LIGHT

3 1532500 78" CORD SET 16/3 AWG 3 1506600 78" CORD SET, EUR

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1327900 INFINITE SWITCH 5 1327310 INFINITE SWITCH

6 1431108 HEAT CABLE, 136", 120V 6 1431132 HEAT CABLE, 136", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

72" 1 8705610 KNOB 72" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1514000 INDICATOR LIGHT

3 1532500 78" CORD SET 16/3 AWG 3 1506600 78" CORD SET, EUR

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1327900 INFINITE SWITCH 5 1327310 INFINITE SWITCH

6 1431111 HEAT CABLE, 160", 120V 6 1431135 HEAT CABLE, 160", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

UNIT

SIZE ITEM P/N DESCRIPTION UNIT

SIZE ITEM P/N DESCRIPTION

120 V0LT UNITS 220 VOLT UNITS

PARTS LISTS & EXPLODED VIEW

24" 1 8705610 KNOB 24" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1513903 INDICATOR LIGHT

3 1547000 CORD SET 16/3 3 1547000 CORD SET, 16/3

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1328200 INFINITE SWITCH 5 1328200 INFINITE SWITCH

6 1431113 HEAT CABLE, 60", 208V 6 1431125 HEAT CABLE, 60", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

36" 1 8705610 KNOB 36" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1513903 INDICATOR LIGHT

3 1547000 CORD SET 16/3 3 1547000 CORD SET, 16/3

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1328200 INFINITE SWITCH 5 1328200 INFINITE SWITCH

6 1431114 HEAT CABLE, 84", 208V 6 1431128 HEAT CABLE, 84", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

48" 1 8705610 KNOB 48" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1513903 INDICATOR LIGHT

3 1547000 CORD SET 16/3 3 1547000 CORD SET, 16/3

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1328200 INFINITE SWITCH 5 1328200 INFINITE SWITCH

6 1431117 HEAT CABLE, 108", 208V 6 1431129 HEAT CABLE, 108", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

60" 1 8705610 KNOB 60" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1513903 INDICATOR LIGHT

3 1547000 CORD SET 16/3 3 1547000 CORD SET, 16/3

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1328200 INFINITE SWITCH 5 1328200 INFINITE SWITCH

6 1431120 HEAT CABLE, 136", 208V 6 1431132 HEAT CABLE, 136", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

72" 1 8705610 KNOB 72" 1 8705610 KNOB

2 1513903 INDICATOR LIGHT 2 1513903 INDICATOR LIGHT

3 1547000 CORD SET 16/3 3 1547000 CORD SET, 16/3

4 8967400 STRAIN RELIEF 4 8967400 STRAIN RELIEF

5 1328200 INFINITE SWITCH 5 1328200 INFINITE SWITCH

6 1431123 HEAT CABLE, 160", 208V 6 1431135 HEAT CABLE, 160", 240V

7 2119200 BUMBER FEET 7 2119200 BUMBER FEET

UNIT

SIZE ITEM P/N DESCRIPTION UNIT

SIZE ITEM P/N DESCRIPTION

208 V0LT UNITS 240 VOLT UNITS

EXPLODED VIEW

Warranty Procedure

IF YOU NEED WARRANTY SERVICE FOR YOUR APW EQUIPMENT, FOLLOW THESE STEPS:

1. Secure the model and serial number from the data tag of your unit.

2. Non-portable equipment - The service agency will dispatch a technician to your location for repairs.

3. Portable equipment - If you request service at your location, you will be responsible for payment of

travel and mileage charges. You can take the unit to the service agency to avoid these charges.

4. For the name of the closest authorized service/parts distributor consult the published list supplied

byAPW Wyott or call theAPW Wyott Service Hot Line, 1-800-733-2203

Notes:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere APW Wyott Speisenwärmer Handbücher

APW Wyott

APW Wyott FDDB-18 Bedienungsanleitung

APW Wyott

APW Wyott HDC-4 Bedienungsanleitung

APW Wyott

APW Wyott Radiant Black FDB-18 Bedienungsanleitung

APW Wyott

APW Wyott BS-1 Bedienungsanleitung

APW Wyott

APW Wyott OVERHEAD WARMERS FD Bedienungsanleitung

APW Wyott

APW Wyott W-3Vi Bedienungsanleitung

APW Wyott

APW Wyott HFWS-2 Bedienungsanleitung

APW Wyott

APW Wyott CW-3A Bedienungsanleitung

APW Wyott

APW Wyott HDC-4 Bedienungsanleitung

APW Wyott

APW Wyott DWC13 Bedienungsanleitung

APW Wyott

APW Wyott CWK-1 Bedienungsanleitung

APW Wyott

APW Wyott BM-30 Bedienungsanleitung

APW Wyott

APW Wyott SM-50-11 Bedienungsanleitung

APW Wyott

APW Wyott Porta-Stove CHP-1A Bedienungsanleitung

APW Wyott

APW Wyott HFW-1 Kurzanleitung

APW Wyott

APW Wyott DWC13-N Bedienungsanleitung

APW Wyott

APW Wyott HFW-43 Bedienungsanleitung

APW Wyott

APW Wyott Classic RCW - 7 Bedienungsanleitung

APW Wyott

APW Wyott W-3V Bedienungsanleitung

APW Wyott

APW Wyott EHP-H Bedienungsanleitung

APW Wyott

APW Wyott W-46V Bedienungsanleitung

APW Wyott

APW Wyott Classic RCW - 7 Bedienungsanleitung

APW Wyott

APW Wyott W-3Vi Bedienungsanleitung

APW Wyott

APW Wyott SHFWEZ-1 Bedienungsanleitung

Beliebte Speisenwärmer Handbücher anderer Marken

ARREDO

ARREDO Illusion 1000 Bedienungsanleitung

Vollrath

Vollrath Mirage 74701DW Bedienungsanleitung

Moffat

Moffat BKRW3 Service-Handbuch

Hupfer

Hupfer SPTW-2/EBF Bedienungsanleitung

Kontour

Kontour K1043E Bedienungsanleitung

Hatco

Hatco Glo-Ray GRMW-3 Anwendungshandbuch

HATO

HATO Macho Nacho FST-1-MN Bedienungsanleitung

Wittco

Wittco 500-CW Bedienungsanleitung

Wells

Wells SS-276ULT Bedienungsanleitung

Kerbl

Kerbl FastHeat Bedienungsanleitung

Johnson

Johnson Kaldino Bedienungsanleitung

Wells

Wells BMW206ULRTD/AF Bedienungsanleitung

KRATOS

KRATOS 29М-008 Bedienungsanleitung

Wells

Wells M227 Series Bedienungsanleitung

Henny Penny

Henny Penny HCS-2 Bedienungsanleitung

Amba

Amba RADIANT RSWH-P Bedienungsanleitung

Homecraft

Homecraft BS15BS Bedienungsanleitung

Hatco

Hatco PW Series Bedienungsanleitung