Aqua J-8010 Bedienungsanleitung
3
Content
Cover 1
Acknowledge 2
Content 3
Important Precautions 4
Filtration Introduction 5
Filtration Technical Parameters 6
Prepare Technical Compartment Pit 6~7
Prepare Indoor Control Panel Pit 8
Connect The Control Panel To The Unit 8
Operation Guiding For Parts Of The Unit 9
Guiding For By Pass Pipes 9
Instruction Of The Control Panel 10~12
Clean The Pool Manually With Filtration System 13~14
Daily Maintenance 14
Frequent Asked Questions 14
Guarantee of services 15
4
Important Precautions
1. In order to prevent severe damage to the unit, never power on the unit when it is outside of the
swimming pool.
2. The power cord must be connected to an appropriate earthed socket.
3. Do not operate the unit when people are in the pool.
4. Ensure the drainage pipe for technical compartment leakage is pre-buried.
5. For optimal performance, before power on make sure that there is no air left inside the unit
(full of the water through priming jet which is inside of the unit).
6. Do not try to lower the unit down to the level of the ground. Install them always above the
ground according to the installation guidance.
7. Before power on, make sure the unit is connected well with the control panel, which could
affect the unit’s performance or cause damage.
8. The filter bags should be cleaned every time you use the unit. This will prevent that the dirty
filter bags affect the normal operation of the unit.
9. The unit should be stored in a cool and ventilated place or protected with cover, away from
direct sunlight, when not in use.
10. The control panel should be placed indoor area. In order to avoid raining and the potential
damage of components, never cover the control panel with wet items.
11. Only authorized after sales service personnel should open the technical compartment and the
control panel, otherwise the warranty will be invalidated.
12. In order to avoid any accident, it is strongly recommended to connect the handrail with the unit
(included in the box) for the safety of going up and down the pool.
13. Do not use the unit beyond the working environment/conditions stated in this manual.
Please read the instruction manual carefully before use and keep it for future
reference.
5
Introduction
“Degaulle” Pool Water Treatment Principle
Vacuum negative pressure has been produced when the motor and pump running
→Raw water will be drawn from skimmer opening on the side of the unit to the filter
basket (Water come into the basket from the surface to filter the leaves…)
→After basket filtered, water outgoing to the filter bag (5~15microns) for precision filtered
→After filtered by Bag filter, water will be discharged back to the pool
→”Degaulle”filtration system includes all traditional system functions
→It is efficiency, coupled with easy maintenance, will provide complete satisfaction.
“Degaulle”Pool Filtration System Features
1. High filtering capability: it can reach up to 5um.
2. Room saving: No operation room needed, it has the ABS, PP or PE housing instead
of the operation room. Nowadays, the earth for building is really expensive, so this
filter can be your best choice.
3. Pipe free: Our filter system does not need pipelines any more, so it can help with the
leakage problem.
4. Auto chemical feeder: Chemicals can be sent to pool automatically once the motor
start, if you do not like to put chemicals to pool, switch off the valve.
5. Vacuum functions: This system has two vacuum functions. All dirt &debris can be
sucked into the skimmer basket or sucked through the vacuum pipe then out.
6. Massage functions: Our machine has turbo boost massage jet, something like
Jacuzzi. And air switch can be used to control the air bubble. And auxiliary jet can
assist the massage jet to strengthen the power of the water to massage.
7. Multiple functions: No underwater light, handrail, ladders, transformer, pump, sand
filter needed any more, etc.
8. Environmental &Reliable: We start this system for more than 6 years and have
thousands of successful cases in locally and overseas. And our machines are with
CE approvals already. Successfully exported to India, Singapore, Taiwan, France,
Turkey, Vietnam, Laos, and Cambodia…etc.
9. Warranty: We offer 2-year-limited warranty for our machine.
10. Professional technical supports: Our senior managers are with 22 years
experience in swimming pool filters, so we ensure you that we can help you with any
difficulties if needed and offer you our best services.
11. Corrosion Proof Housing: This machine is made out of PP material with the
functions of anticorrosion, watertight protection, scratches, cracks, tears proof etc...
12. Digital Control panel: Three groups working time setting, automatic and manual
6
working mode, overheating, overvoltaging, overcurrent protection etc…
“Degaulle”Filtration System Technical Parameters
Model Number: J-8010
Specification: 960×580×810mm
Power: 0.75Hp
Voltage: 220V/50Hz
Filtering: 15m3/h
Underwater Light: 6W/12V LED
Filter Capability: 5um
Filter Medium: Bag Filter
N.W.: 80Kgs
G.W.: 95Kgs
Available Colors: White, Yellow, Blue, Red
Packing Size:
Main Host:1060×670×880mm
Handrail: 1140×810×100mm
Prepare Technical Compartment Pit Beside The Pool
1. Please make sure The Gap (Pool wall for supporting the filtration unit) between
technical compartment and filtration compartment is 25cm.(Fig.1)
7
Fig.1
2. Please ensure the size for technical compartment pit is : 960×530×420mm (Fig.2)
3. Please make sure there is drainage pipe for the technical compartment water
outgoing. (Fig.2) if there is no connector inside of the unit; please open a suitable hole
yourself. But please make sure the location is well connected with the drainage pipe.
Fig 2
4. Please take care of the wire in the electrical conduit pipe to connect the technical
compartment is 4*2.5m2;If possible, please make the wire inside of a protective
sheath.
5. Please leave the handrail 2 round holes for installation accordingly.(Fig. 3)
Handrail Hole
8
Fig. 3
6. Please backfill fine sand (Depth≥110mm) at the bottom of the technical compartment
pit for shock absorption and noise level reduction.
7. Please backfill sand or concrete and then coping stone to fix the unit and decorate the
gap between compartment and the pool wall.
Prepare Indoor Control Panel Pit
1 The size for indoor control panel pit should be 280×180×100mm (Fig. 4)
2 Control panel is not water proof, is a must to install it indoor and never cover or wet it
Fig. 4
Connect The Control Panel To The Unit
1. Connect the cable to the junction box inside of the unit. (Fig. 5)
2. Connect the cable to the control panel.(Fig 5)
9
Fig 5
Operation Guiding For Parts Of The Unit
1. Empty air inside of the pump and plumbing system inside of the unit with full of water
through the priming jet.
2. Add Chemicals into the chlorine feeder (if there is in the technical compartment)
or filter basket in filtration compartment.【Ref.: 4g chlorine for 1 m3pool water】
3. Strengthen power with pneumatic switch to change the pump speed to high or low
4. Close the side water nozzle to strengthen the front nozzle power.
5. Boost the water bubble by air switch
6. Change the directions of the discharge nozzle for massage or filtration.
Guiding For By Pass Pipes
1. Vacuum Ports
There are two vacuum ports in our filtration unit. Vacuum inlet locates at the side of
filtration compartment (front vac.port) and vacuum outlet locates at the side of
10
technical compartment (back vac.port).get the vacuum hose to be well connected
with front port and turn the valve inside of the filtration system to correct position, start
the motor to begin the vacuum. (Fig. 6)
2. Delivery/Return
Connect the port at the side of technical compartment to plumbing system around the
pool and close the port at the side of the filtration system. Turn on the motor to start
filtering to deliver /return the water. (Fig. 6)
Fig. 6
Instruction Of The Control Panel
Basic Operation Guiding
POWER: (This switch cannot shut down the general power, please shut down the
general power if long time no uses our unit).
Press “POWER” button，the unit will work and the indicator above the button will be
on in red.
①When the pump working mode is manual, screen
will display content same as below (Fig. 7)
Fig. 7
②If no setting, pump will keep manual working mode as default, at this time we can
Press “PUMP”Button to switch on/off pump.
③When Pump working mode is Auto, screen will display the content same as below
Vacuum Discharge Port
or Delivery /Return Port
Vacuum Suction Port or
Delivery /Return Port
11
(Fig.8) .If no setting, pump will enter into automatic working mode; “PUMP” button will
not work and the unit will work according to the date& time displaying in the screen.
Fig. 8
④Press “POWER”button again, the unit will be standby, Indicator above the button
will be off. Screen will display content same as below. (Fig. 9).
Fig. 9
⑤“PUMP”Button: When the working mode is manual, press “PUMP”button to
Switch ON/OFF pump, Indicator above the button will be on/off accordingly.
⑥“LAMP” Button: Press “LAMP”button to Switch ON/OFF the lamp, Indicator
above the button will be on/off accordingly.
⑦“OZONE” Button:Press “OZONE”button to Switch ON/OFF the ozonator,
Indicator above the button will be on/off accordingly.
⑧“UP”Button: Adjust the menu upward
⑨“DOWN”Button: Adjust the menu downward
⑩
MUNE
“MENU” Button: Menu all functions
⑪“ENTER” Button: Confirm all information you chose.
Functions in Menu
①Date, Time and Week setting
Inhaltsverzeichnis
Andere Aqua Schwimmbadfilter Handbücher
Beliebte Schwimmbadfilter Handbücher anderer Marken
Davey
Davey EcoPure DEP2140 Bedienungsanleitung
JUWEL Aquarium
JUWEL Aquarium EccoSkim Bedienungsanleitung
POLYGROUP LIMITED
POLYGROUP LIMITED SFS600 Filter System with F600C Pump Bedienungsanleitung
Pentair Pool Products
Pentair Pool Products Filter CFW Series Bedienungsanleitung
Oase
Oase Skimmer 250 Bedienungsanleitung
Oase
Oase CrystalSkim 350 Bedienungsanleitung