AquaTools AT5800 Bedienungsanleitung

AUTOMATIC POOL CLEANER

O W N E R’ S M A N U A L

OPERATION, TROUBLESHOOTING & PARTS

AquaTools

293 Wright Street, Delavan, WI 53115

International: 262-728-5551, FAX: 262-728-7550

ABOUT SAFETY

•Before installing the cleaner, review and

understand all warnings and safety information

on inside cover of manual.

ABOUT INSTALLATION

•Please use the convenient, water resistant

Installation Instructions card.

INDEX

About Safety .............................................................2

About Your Pool and Filter System ...........................2

About Installation .....................................................3

About the Cleaner Operation....................................4

About ”Fine Tuning” Vacuum Adjustments............4,5

About the Cleaner and Accessories...........................6

About Troubleshooting .............................................7

About Disassembly ...................................................8

About Assembly........................................................9

Repair Parts.............................................................10

About Maintenance ................................................11

Warranty.................................................................12

1873 0795

Model AT5800

Before installing your cleaner, review and

understand all warnings and safety informa-

tion on the inside front cover of this manual.

Pre-installation check list

Before installing the cleaner in a vinyl liner pool:

Check liner closely for signs of deterioration or damage

from age, chemicals, pool wall damage, etc. If any dam-

age is found, have a qualified pool professional make

all necessary repairs. Also, if there are stones, roots,

etc., under the liner, remove them before installing the

cleaner.

Before installing the cleaner in a gunite pool or a pool

that is partially or completely tiled:

Repair loose tiles and tighten any loose light rings.

Before installing the cleaner, clean your filter system:

Make sure you have cleaned the filter, including back-

washing, rinsing, and emptying all baskets. A clean

system is necessary for proper cleaner operation and

coverage.

Before installing the cleaner, fill the hose with water:

Always make sure the cleaner head is submerged and

the hose is full of water before connecting the hose to

the filtration system (whether through a skimmer or

dedicated wall fitting). Air in the system can damage

the pump through dry running and overheating.

Before installing the cleaner, understand cleaner cov-

erage:

The cleaner is designed to rid your pool of debris in

approximately 4-6 hours. Less time could be needed,

depending on the pool size.

The cleaner was not designed to automatically clean

steps or swimouts or to work under a solar cover. It

was also not designed to do initial cleanup for a new

pool or when opening your pool for the season.

Suction entrapment, injury, and drown-

ing hazard. If your pool has a dedicated suction

port (“vac port”) for vacuuming or for an automatic

pool cleaner, it must be covered when not in use.

A spring loaded safety cover is included with your

cleaner. Install it on the suction port to prevent

entrapment and injury.

ABOUT YOUR POOL AND FILTER SYSTEM:

This is the safety alert symbol. When you see

this symbol on your system or in this manual,

look for one of the following signal words and be

alert to the potential for personal injury.

warns about hazards that will cause

death, serious personal injury, or major property

damage if ignored.

warns about hazards that can cause

death, serious personal injury, or major property

damage if ignored.

warns about hazards that will or can

cause minor personal injury or property damage if

ignored.

Carefully read and follow all safety instructions in

this manual and on equipment. Keep safety labels in

good condition; replace if missing or damaged.

Hazardous suction.

Can trap and tear

hair or body parts.

Can cause drowning.

Do not play with cleaner

or hose or apply to body.

Do not let children use or

play with pool cleaner.

Stop pump before

attempting to clean unit.

1058 0594

Oscillator may

injure hands or fingers.

Stop pump before attempt-

ing to clean out pool cleaner

head.

Hose can trip

or entangle swimmers.

Do not allow swimmers in

pool while pool cleaner is

operating.

Please read the following before installing

your new automatic pool cleaner!

ABOUT SAFETY:

1882 0795

Vacuum

Regulator

w/2 Caps

Swivel

Ass'y

Reducer

Cone

Hose

Cleaner

Vac Port

20'

1881 0795

8' 4'

1880 07

Skimmer

Vac

Port

Swivel

Assembly

Hose must equal longest stretch — — plus at least 4 feet.

Figure 1

Figure 2

Figure 3 Figure 4

Figure 5 Figure 6

Figure 7

Hose Cuff

marked

"Connect

to Cleaner"

1875 0795

White Rubber

Reducer Cone

White Plastic

Vacuum Regulator

ABOUT INSTALLATION

Please use the convenient, water resistant, “Installation Instructions” card.

Step 1: Straighten hose (Figure 1)

Remove and uncoil the hose from the carton. Lay it out

in the sunlight, flat and straight.

Step 2: Check parts (Figure 2)

Cleaner, black plastic swivel assembly, white rubber

reducer cone, one 20’, one 8’, and one 4’ hose, white

plastic vacuum regulator, extra black regulator cap

marked “50”, vac port fitting.

Step 3: Clean filter system (Figure 3)

Backwash and clean filter; rinse; clean all baskets, etc.

Start pump.

Step 4: Adjust valves for vacuuming (Figure 4)

Decide on the vacuum connection you are going to use

(either a skimmer or a dedicated wall fitting) and adjust

the pump valves (if your system has valves) to direct all

vacuum there.

Close the main drain (also see “About Fine Tuning the

Vacuum”, Page 4)

Step 5: Assemble cleaner (Figure 5)

Insert swivel assembly into cleaner; twist 1/4 turn.

Step 6: Measure hose length needed (Figure 6)

Before connecting the hose, lay it out from the vacuum

connection you are using (whether skimmer or dedicat-

ed wall fitting) to the furthest point of the pool. The

hose should be at least 4’ longer than this. More than 4’

longer is OK. Do not cut the hose.

Step 7: Connect hose to cleaner (Figure 7)

Connect the 24’ hose end marked “connect to cleaner”

to the black swivel assembly. Connect the white plastic

vacuum regulator to the opposite end of the hose. Insert

the regulator into the white rubber reducer cone.

Step 8: Connect hose to filter system (Figure 8)

Fill the cleaner and hose with water and connect to the

suction source. The cleaner will begin to operate.

Figure 8

Clicking sound

This sound is the oscillator moving back and forth in

the oscillator chamber. The best speed for it is about

500 oscillations per minute. The vibration created by

the oscillator moves the bristles and the cleaner. If the

oscillator is running too fast, the cleaner will have a

tendency to climb up the pool wall past the waterline,

or “walk out of the pool”.

Movement around the pool

Random motion – The cleaner will visit most spots in

the pool in a 6 hour period. It is not specifically pro-

grammed and cannot see the dirt you are seeing. It is a

random motion cleaner.

The cleaner was designed to spend most of its time in

the deep end, where most of the floor and wall area

exists. During a 6 hour period the cleaner will visit the

shallow end a few times.

Rotating motion – The cleaner will rise up on one side

and pivot a few times per minute. This is normal and

provides the following:

1. Allows leaves that are being pushed or dragged along

to be sucked up into the vacuum chamber.

2. Allows the cleaner to:

Change direction

Get out of corners

Get away from ladders

Submerge below pool water level

Get off of domed main drain covers

Picks up big “stuff”

The cleaner will pick up some debris so large that it

may jam. Simply stop the pump and remove the debris

from the oscillator or the swivel assembly.

ABOUT THE CLEANER OPERATION:

ABOUT “FINE-TUNING” VACUUM ADJUSTMENTS AND CONNECTIONS:

Pool pump suction is hazardous and

can cause entrapment with severe personal injury

or drowning. Use vacuum regulator (see instructions

below) in pool cleaner system at all times.

Note: Each pool’s hydraulic system and vacuum con-

nections are different. Be sure you have installed the

white plastic vacuum regulator before you “fine-tune”

the system. This not only regulates vacuum, but also

acts as a safety device.

Suction entrapment, injury, and drown-

ing hazard. If your pool has a dedicated suction

port (“vac port”) for vacuuming or for an automatic

pool cleaner, it must be covered when not in use. A

spring loaded safety cover (the “Vac Port Fitting”) is

included with this pool cleaner. Install it on the suction

port to prevent entrapment and injury. For details

please refer to the Vac Port instruction sheet included

with your Vac Port.

For the “NOVICE POOL OWNER” where vacuuming

is a new experience, please read all of the following

points, installation instructions, and trouble shooting

guide carefully.

Please note the following:

• “Vacuum” and “suction” are two words meaning the

same thing.

• “Dedicated suction line”, “vac port”, and

“vac fitting” are different terms for a

hole in the side wall of pool; this hole

is connected to the pump suction and

is dedicated to vacuuming.

•Some pools do not have a vac port. If

your pool does have one, please read

the “Suction Entrapment” warning at left.

For the “SEASONED POOL OWNER”: The automatic

pool cleaner connection and vacuum adjustments can

be similar to using your manual pool vacuum. Please

read on.

Valves (pump, skimmer, and main drain) and

vacuum adjustments

You may need to spend some time adjusting the skim-

mer and main drain valves in order to obtain the best

vacuum setting for good cleaner operation. Once you

have found the correct valve settings for best operation,

we suggest you mark the valves to ensure repeated

success.

At first, set valves to give maximum vacuum to the

skimmer or vac fitting you have elected to use.

Vac

Port

Too much vacuum?

You have too much vacuum if the cleaner climbs up the

pool wall past the water line to the point that the clean-

er sucks air and the pump loses prime. Frequent loss of

prime will damage the pump. To correct this, change

the black vacuum regulator cap marked “60” to the one

provided in your accessory bag marked “50”. If the

cleaner still climbs out and sucks air, open the main

drain valve slightly.

Not enough vacuum?

You don’t have enough vacuum if the cleaner moves

sluggishly or not at all. Be sure the filter system is clean

and all valves are adjusted to give you maximum vacu-

um. If the cleaner is still not moving, your pump may

not be strong enough to operate the cleaner. Also,

please refer to the Troubleshooting guide on Page 7.

In-Line leaf Canisters

If your pool is exposed to large quantities of leaves, we

suggest purchasing and installing an in-line leaf canis-

ter. A leaf canister will provide more debris-loading

capacity and also provides a water by-pass when the

canister is full. It is very important that the pump not

starve for water!

Dedicated suction line/vac port/vac fitting

Some pools have a dedicated wall fitting just for vacu-

uming. If the wall fitting connection is used, you may

notice that the clear pump lid shows signs of bubbles or

what appears to be the presence of air. To eliminate

this, slightly open the main drain valve to supplement

the water intake. The cleaner may slow down a bit

when you change the suction.

Skimmer connection

Some pool owners remove the skimmer basket and

connect the hose directly into the bottom of the skim-

mer. This method is OK for pools with minimal debris

and also for screened in pools.

For pools that have large quantities of “big stuff” to

pick up, we suggest using the bottom of the skimmer

connection in conjunction with an in-line leaf canister

(purchase the cannister locally). A leaf canister will pro-

vide more debris-loading capacity and also provides a

water by-pass when the canister is full. It is very impor-

tant that the pump not starve for water!

Skimmer vac plates

Some pool owners connect the hose to a skimmer vac

plate, which allows the skimmer basket to remain in

the skimmer. If this method is used, empty the basket

frequently. Also make sure that the vacuum regulator

provided is completely submerged so that it will not

suck air and damage the pump.

Skimmer vac plate vacuum

control adjusters

Some pool owners use one of a variety of manufacturer’s

skimmer vac plates. Some have a vacuum control ad-

juster, and some do not. The adjuster could be a screw-

type, a spring loaded apparatus, or a dial design. For

those vac plates with adjusters, it is important to adjust

them when fine tuning the vacuum for the cleaner.

ABOUT “FINE-TUNING” VACUUM ADJUSTMENTS AND CONNECTIONS:

If you have any questions, please call 1-800-752-0183

ABOUT THE CLEANER AND ACCESSORIES:

Swivel assembly (Figure 9)

Installing the swivel assembly is a snap.

Just insert it into the cleaner body and

give it a quarter turn.

If you attach a unidapt handle to the

swivel for manual vacuuming, be sure it

is the special, floating unidapt handle

provided with the cleaner (Replacement

Part No. AT5119). Use of a different

unidapt handle will hinder the cleaner’s performance.

Hoses (20’, 8’, and 4’ lengths – Figure 10)

The unit includes a 20’ hose, an 8’

hose, and a 4’ hose. Do not cut any of

these hoses.

The best hose length is at least 4’

longer than the distance from your

suction source (whether skimmer or

dedicated suction line) to the furthest

point in the pool. If the hose seems to

be too long, remove the 8’ section

provided. Do not cut the 20’ hose.

Be sure to connect the tapered end of

the 20’ hose (marked “connect to

cleaner”) to the cleaner head.

If additional hose is needed, use only

the specially designed 8’ extension hose from your

Aquatools dealer (order replacement part No. AT5111).

Use of another manufacturer’s hose will hinder cleaner

coverage (this also holds true for the 20’ hose). If you

need to replace the 20’ hose, buy only the original

equipment hose (order replacement part No. AT5821).

Hose (6” connector ) female x female (purchase acces-

sory No. AT5121) If required, this will accommodate a

male x male connection at the skimmer.

Reducer cone (Figure 11)

The reducer cone is required to make

most hose connections. When used, it

will keep the hose in place if the filter

system is stopped.

Automatic vacuum regulator (Figure 12A)

Hazardous suction. Can cause entrap-

ment with severe personal injury or drowning.

Vacuum regulator should be installed in

all situations. If the cleaner moves very

slowly or not at all (indicating low vacu-

um in the system), see Troubleshooting

Guide, Page 7.

The regulator includes two black rubber

regulator caps. One is installed on the

regulator at the factory, and one is in the

accessory bag. The cap marked “50” in the accessory

bag is for systems with extremely high vacuum. Use of

this cap will help prevent the cleaner from “walking”

out of the pool.

Make sure the vacuum regulator, especially the black

rubber cap, is submerged at all times. If not, the pump

will suck air through the regulator and lose prime. This

could damage the pump.

Vac port fitting (Figure 12B)

Suction entrapment, injury, and drown-

ing hazard. If your pool has a dedicated suction

port (“vac port”) for vacuuming or for an automatic

pool cleaner, it must be covered when not in use.

A spring loaded safety cover (the

“Vac Port Fitting”) is included

with this pool cleaner. Install it

on the suction port to prevent

entrapment and injury. For

details please refer to the Vac

Port instruction sheet included

with your Vac Port.

1883 0795

20'

Figure 9

Figure 10

Figure 11

Figure 12A

ABOUT BUMPER INSERTS

Bumper Inserts (see Key 2A, Page 10) help to make the

cleaner more buoyant to allow better access to the

shallow end of the pool. Do not install inserts from the

top; they will become jammed and not work properly.

Only install inserts from the bottom.

If the bumper on the cleaner appears to lift the cleaner

to the surface of the pool, check for trapped air in the

cleaner and hose. If no air is found, remove one

bumper insert block and watch and see if the cleaner

remains submerged and on the pool floor while work-

ing. If not, remove individual insert blocks as needed

until the cleaner rests on the pool floor and operates

properly.

Vac

Port

Figure 12B

SOLUTIONS:

1. Backwash and/or clean filter. Empty all baskets. This should help your cleaner attain the

desired oscillation rate of 400-600 times per minute.

2. Clear all debris from oscillator chamber, hose, or vac plate by-pass (if you have one).

3. Repair all sources of vacuum leaks (cracked vac plate, vac plate or reducer cone not seated

properly, cracked hose, vac plate by-pass adjusted too loosely).

4. Adjust valves to give maximum vacuum to the vacuum port or skimmer to which you are

attaching the cleaner hose. Reduce or shut off other skimmers and main (floor) drain.

Note: Each pool’s hydraulic system is different. It may require some adjustments to skimmer

and main valves before you achieve the vacuum setting required for the best cleaner to opera-

tion. Once determined, mark the valves at that position to ensure repeated success.

5. Filtration system (pump) does not develop enough vacuum. Consult your pool service

professional.

6. In hot water, the hose may kink. The hose, when old, may have developed leaks

(cracks or holes) or may get brittle. Purchase new hose.

NOTE: It must be an AquaTools hose for proper operation.

1. Oscillator is running too fast. Make sure vacuum regulator is installed.

2. If regulator is installed and cleaner still climbs out of the pool (sucking air), remove the black

rubber regulator cap and replace it with the cap marked #50 from the accessory bag.

3. If steps 1 and 2 do not solve the problem, slightly open the main drain valve until the cleaner

no longer climbs out of the pool.

1. A clean filter system will help the cleaner to move much faster. Also, be sure to clean all baskets.

2. Vinyl liner pools with a deep end hopper will require 6-8 hours to clean. In this time the

cleaner should make at least 4 trips to the shallow end. If not, call Customer Service at

1-800-752-0183.

3. Examine the turning brush mechanism as the cleaner is operating. To do this, you will have to

turn the cleaner over while it is running and submerged. If the turning brush does not move to

the “down” position within 2 minutes, call Customer Service at 1-800-752-0183.

4. The cleaner was not designed to work under solar covers. If you have a solar cover, only mini-

mal coverage can be expected.

5. At times strong winds may hinder cleaner coverage!

6. Any cleaner might miss a spot. Your cleaner has been designed to accommodate the attach-

ment of a vac-pole (telepole) by use of the handle in the accessory bag. Attach pole for spot

cleanups, steps, and swimouts.

1. Examine the turning brush mechanism as the cleaner is operating. To do this, you will have to

turn the cleaner over while it is running and submerged. If the turning brush does not move to

the “down” position within 2 minutes or less, call Customer Service at 1-800-752-0183.

1. This cleaner was not designed to clean these areas. Use the handy telepole attachment, connect

the pole, and clean missed areas.

1. This is normal with some filter systems that develop a surge of back pressure when the system

shuts off. The cleaner will right itself when the system is restarted.

1. Use reducer cone when connecting to the skimmer or vac port.

1. Hose might be too short. Desired length can be measured from the point where the hose is con-

nected, to the furthest point of the pool, plus a minimum of an additional 4’. If needed, pur-

chase an extension hose from your local dealer. Do not cut extension hose – use it full length

even if it is a little long.

1. For best results, when hose is not in use, store it uncoiled, flat, and straight. If coiling is

necessary, coil loosely.

2. Lay hose out flat and straight in the sunlight for a few hours prior to use.

ABOUT TROUBLESHOOTING

SITUATION

Cleaner does not move.

Oscillator is very slow.

Cleaner climbs past water

line of pool causing pump

to lose prime (suck air).

Cleaner coverage not as

expected.

Cleaner “stuck” in one

spot (more than 15

minutes).

Steps and “swimouts” are

not clean.

Cleaner flips on its back

when pump stops.

Hose comes loose when

pump stops.

Cleaner hovers in one

area with hose fully

extended.

Hose keeps coiling up.

If you have any questions, please call 1-800-752-0183

1. Remove swivel assembly (Figure 13) from the top of

the cleaner by turning it 1/4-turn counterclockwise

and pulling straight up on it.

2. Turn cleaner upside down. Remove 4 screws and

remove lower body assembly from shroud.

3 . Turn lower body assembly right side up. Unsnap the

2 clips on the oscillator chamber cap (Figure 14A); lift

it off.

4. Pull the long gear shaft straight up (Figure 14A) by

the blocks on the ends of the shaft. Hold the seals in

the oscillator and the blocks on the shaft. The cam

may interfere with the shaft mounting post; if so, turn

it slightly on the shaft until it clears the post. The shaft

assembly can now be disassembled (Figure 14B).

5. Slide the long gear shaft out of the oscillator (with

gears, complete); make sure that you don’t lose the

seals out of the oscillator which may fall out at this

point (Figure 14B).

5A. Oscillator seals are replaceable.

5B. Ratchet gear set and long shaft are replaceable as a

unit.

6. Remove the set screw, short gear shaft, and gears

(Figure 15); do not lose the gears off of the shaft.

7. With a small screwdriver (such as a jeweler’s screw-

driver), a pencil, or a pen point, depress and remove

the coil spring from the movable brush mounting

post (Figure 16). Replace the brush and the spring if

necessary.

8. The metal ratchet tab slides out of its slot sideways;

replace it by removing the center brushes and sliding

in a new ratchet tab until it is flush with the edge of

plastic holder (Figures 17 and 18). Replace the center

brushes.

9. The brush ring pops out of the cleaner body for easy

replacement.

10. If you need to replace the bumper, turn the shroud

and bumper assembly upside down and remove the

two screws holding the bumper to the shroud.

1889 0795

Clip

Ocillator

Chamber

Cap

Block

Long Gear Shaft

Block

Cam

Locked Twist CCW

1/4 Turn

Pull Straight

"Click" at

this point

Swivel

assembly

3337 1098

4374 0503

1887 0795

1886 0795

1. Slide metal ratchet tab

toward end of cleaner body

1885 0795

2. Slide metal ratchet tab

down through cleaner body

1884 0795

Figure 14A Figure 14B

Figure 13

Figure 15 Figure 16

Figure 17 Figure 18

ABOUT DISASSEMBLY

ABOUT ASSEMBLY

If you have any questions, please call 1-800-752-0183

1. Put both white seals in the oscillator; hold them in

place.

2. Install the oscillator on the long gear shaft. Install the

ratchet gear on the shaft so that the teeth engage the

ratchet on the oscillator. Install the spring, ratchet

drum, pinion gear (large gear first), and cam (gear end

first) on the shaft (See Figure 19). Hold the gears on the

shaft while installing them, and compress the clutch

spring to allow assembly to slip into place between the

posts (See Figure 19).

3. Install the long gear shaft and end blocks in the clean-

ing head with the large arm of the cam down (see

Figure 20).

4. Reinstall the short gear shaft, set screw, and two gears

(See Figure 21); the small pinion gears and the shaft set

screw go on the side toward the end of the cleaner –

away from the oscillator box. Make sure that the gears

engage the gears on the long gear shaft.

5. Install the oscillator chamber cap and clip it in place.

6. Install the rubber vacuum skirt on the cleaner with the

word ‘OUTSIDE’ showing. Start at the large pin on the

back of the cleaner head (See Figure 22) and work

around the cleaner. Make sure the skirt is flush against

the stop strips on the cleaner head (see Figure 23).

7. Turn the cleaner over. If you removed the bumper and

brush ring, replace them now.

8. Install the lower body assembly in the shroud. Fasten

the cleaning head in place with 4 screws (2 long, 2 short

– see Figure 24).

NOTE: Make sure that you do not dislodge the rubber

vac skirt while inserting the lower body assembly past

the brush ring.

1894 0795

Figure 19

Swing Cam

Arm up for

Clearance

Make sure Oscillator

is partially inserted in

chamber while reinstalling

Shaft Assembly

Oscillator

Chamber

Figure 20

Figure 21

Start here with

large button when

installing vacuum skirt.

OUTSIDE

'Outside' will show

(facing out) when

skirt is correctly installed. Rubber

vacuum skirt

1893 0795

Figure 22

This

Not

This

Figure 23

#10-16x1" Screws

#10-16x1-3/4" Screws

Center

Brush

Location

Center

Brush

Location

Bottom View of Cleaner

1891 0795

Figure 24

Repair Parts

Key Part Part

No. Description No.

1Swivel Assembly AT5112

2Bumper AT5802

2A Bumper Insert Kit (Set of 4) AT5820

3Screw Kit (4 short, 2 long) AT5804

4Shroud AT5801

5Brush Ring AT5805

6Oscillator Chamber Cap AT5806

7Cam Kit (2 & 3 Leg Cams) AT5807

8Idler Gear Kit (Incl. 3 Gears) AT5809

9Block Kit (Incl. 2 Blocks) AT5812

10 Long Gear Shaft (Stainless Steel) AT5813

11 Set Screw #4 Self Tapping##

11A Shaft Kit, Stainless Steel (includes Set Screw) GW9536

12 Lower Body* GW9535

13 Lift Brush AT5817

14 Vacuum Skirt AT5808

15 Lift Brush Spring AT5822

16 Ratchet Tab (Stainless Steel) AT5823

17 Oscillator Seal Kit (Incl. 2 Seals) AT5109

18 Oscillator Assembly Kit (Incl. Key # 17) AT5803

(Ratchet Assembly not sold separately)

19 Center Brush Kit (Set of 2) AT5113

•4’ Vacuum Hose Extension (1/pkg.) AT5819

•20’ Vacuum Hose (1/pkg.) AT5821

•8’ Vacuum Hose Extension (1/pkg.) AT5111

•Replacement Hose Kit

(1 each 20’, 8’ and 4’ Hose) AT5816

•Vacuum Regulator Assembly AT5116

•Vacuum Regulator Cap Kit

(Includes #50, #60, #70 Caps) AT5118

•Reducer Cone AT5115

•Unidapt Handle AT5119

•6” Female to Female Adapter Hose** AT5121

•Vac Port Fitting GW9530

•Not illustrated.

*Includes Key Nos. 6, 11A, 13, 15, 16, two idler gears

and 2-arm cam.

** Accessory – purchase separately.

## Not available separately.

Optional Accessories

Unidapt

Handle

No. GW9019

Vacpole

1897 0795

If you have any questions, please call 1-800-752-0183

11A

1896 0795

Unidapt

Handle,

No. AT5119

Vacpole

Andere Handbücher für AT5800

Inhaltsverzeichnis

Andere AquaTools Schwimmbadroboter Handbücher

AquaTools

AquaTools AT5800 Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

Maytronics

Maytronics Dolphin POOL UP Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung