2
TV device setting
TV device settingTV device setting
TV device setting
1.
1.1.
1. nown code input
nown code inputnown code input
nown code input
1) If you know the code that you want to use, simply press and hold the [TV], [SAT] etc key ant then also press
the power key for 3 seconds. The red LED will glow
2) Type in the required code
3) The red LED will go out and the control will be set automatically
2.
2.2.
2. TV Brand Search
TV Brand SearchTV Brand Search
TV Brand Search
1) Turn on TV. Press and hold the device key [TV]
firstly, then press and hold [Brand] key, after 5
seconds LED will light. Please keep holding the
keys brand key, please refer to the following
Brand list.
2) When TV is turned off, release the key, the code
will be saved automatically.
3.
3.3.
3. SAT Brand Search
SAT Brand SearchSAT Brand Search
SAT Brand Search
1) Turn on SAT. Press and hold the
device key [SAT] firstly, then press
and hold [Brand] key, after 5
seconds LED will light. Please
keep holding the keys. Refer to the
following Brand list to find your
SAT belong to which key.
2) When SAT is turned off, release the key, the code will be saved automatically.
3) Code Input, Find the 4 digital codes from the CODE LIST:
SAT Brand list
SAT Brand listSAT Brand list
SAT Brand list
1) Press and hold the device key [TV](OR SAT/DVD/AUDIO) firstly, then press and hold [POWER] key, after 3
seconds LED will light, release them.
2) Input the 4 digital codes. If the codes are right, the LED will be off. If not, the LED will flash 4 times and setting
will be exited.
3) Test the remote control function keys. If it didn’t work well, please repeat Step 1, 2, 3 and try other codes.
NOTICE: During the whole set up process, if no key is pressed in 10 seconds the setting will be exited.
4.
4.4.
4. Automatically search
Automatically searchAutomatically search
Automatically search
1). Turn on TV. Point WURC5A to it. Press and hold [TV] (OR SAT/DVD/AUDIO) key about 7 seconds, LED will be lit.
Release it. It starts to search code automatically.
2). When the DEVICE is powered off, please press [O ] key to save the codes and exit the search mode.
5.
5.5.
5.
Manual Search
Manual SearchManual Search
Manual Search
1) Turn on TV. Press and hold the key [TV] (OR SAT/DVD/AUDIO) firstly, then long press [CH+] about 5 seconds,
TV LED will be lit. Release the keys.
2) Press the key [CH+] OR [CH-], each time you press it will search once. When the channel changes, please press
[O ] to save the code.
3) If long press the key [CH+] / [CH-], it will search fast. When the channel changes, please release the key. Press
[CH-] / [CH+] to adjust the code. If the channel changed again, please press [O ] to save the code.
NOTE: During setting process, if no key is pressed in 10 seconds the setting will be exited automatically.
6.
6.6.
6. Learnin
LearninLearnin
Learning function
g functiong function
g function
1) Press and hold the key [TV] (OR SAT/DVD/AUDIO) firstly, then long press [VOL+] about 5 seconds; the LED will
be lit. Release the two keys. It is ready to learn.
2) Point the original remote control to
WURC5A
WURC5AWURC5A
WURC5A. The distance should be within 1-3 cm.
3) Press the function key of original remote control, the LED of WURC5A
WURC5AWURC5A
WURC5A will keep flashing, then press any key of
WURC5A
WURC5A WURC5A
WURC5A to learn the code. The LED of WURC5A
WURC5AWURC5A
WURC5A will keep light. Please repeat Step 2 to continue learning
other function keys.
4) After learning all the keys, please press and hold the key [TV] (OR SAT/DVD/AUDIO) firstly, then press [VOL-
--
-],
the LED will be extinguished. The learning will be saved.
NOTE: During the learning process, if no key is pressed in 25 seconds the learning state will be exited without saving.
