Arada Hamlet Bedienungsanleitung

BK570 Rev01

EN 13240:2001+

Amd. A2

October 2013

PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE

Boiler User Guide

For stove ranges:

Solution Boilers

Wet Stove User Guide

More than 20 years experience has been put into the development of our stoves to ensure ultimate

performance and years of trouble free use and enjoyment.

and engineered which is why we are so

confident in the reliability of our products.

Should you have any questions about our stoves that are not covered by this manual, please

contact the Arada retailer in your area, or call our technical support department on

08448 567181.

All Arada stoves are tested to European Standard EN 13240.

WARNINGS

Pure Petroleum coke or Bituminous house coal must not be burned in this appliance.

The use of these fuels will invalidate the appliance guarantee.

Arada recommends the use of HETAS approved smokeless fuels which have been deemed suitable

for use on closed appliances, including multi fuel stoves.

If in doubt, contact The Solid Fuel Association, telephone: 0845 601 4406 / 01773 835400 or visit

www.solidfuel.co.uk

It is a legal requirement that the installation of all new or replacement, wood or solid fuel heating

appliances must obtain building control approval from your local authority. This can be done by

using a qualified heating engineer, affiliated to a government approved competent persons

scheme such as operated by HETAS.

If in doubt, contact HETAS limited, telephone: 0845 634 5626 or visit www.hetas.co.uk

A fireguard conforming to BS 8423:2002 should be used in the presence of children and old or infirm

people. Do not use aerosol sprays or any other flammable materials near the appliance when in use.

Arada Ltd will not be responsible for any consequential or incidental loss or injury however caused.

Arada has a policy of continuous product development and therefore we reserve the right to

amend any product specification without prior notice.

Wet Stove User Guide 3

OPERATING YOUR STOVE

Our boiler stoves are designed to be operated

with the fire door(s) closed at all times, apart

from refuelling (when alight) or cleaning (when

cold).

Never leave the appliance unattended for an

extended length of time with the door(s) open.

Visit our Youtube channel for our ‘how-to’

series of videos:

http://www.youtube.com/aradastoves

FUEL TYPES

WOOD

Any type of wood is suitable provided it is well

seasoned and has a moisture content below

20%. This usually implies that the timber has been

suitably stored to allow moisture to evaporate

for at least nine months in the case of soft

woods, and at least twenty four months in the

case of hard wood. We recommend that for

general burning wood should be split into logs of

no more than 100mm (4”) diameter.

WARNING: Wet wood must not be used as this

will greatly contribute to the creation of tar and

creosote which may, in extreme cases, run

damage both the chimney and the appliance

and increase the risk of a chimney fire.

or chimney your wood is ‘green’ or

too wet.

only or chimney damage will occur.

WARNING: NEVER BURN PLASTICS, HOUSEHOLD

WASTE OR LIQUID FUELS IN YOUR STOVE.

SOLID FUEL

Arada recommends the use of HETAS approved

for use on closed appliances, including multi fuel

stoves. These include:

Homefire Ecoal

Homefire Ecoal Instant Light Taybrite

Homefire Newflame

Homefire Ovals Maxibrite

Supertherm Sunbrite

Ancit Pureheat

Phurnacite

For additional advice on fuels, please refer to

The Solid Fuel Association.

LIGHTING THE FIRE

Prior to lighting the stove for the first time, check

with the installer that:

 Installation and all building work is complete.

(Refer to the installation guide.)

 The chimney is sound, has been swept and is

free from obstruction.

 Adequate provision for combustion air has

been made.

 That Building Regulations and any local

by-l

installation guide.

 All firebed surrounds and FEDS are in place.

 That the chimney draw has been checked

and is within specification. With the chimney

warm, the draught should be between 1-2 mm

water gauge or 0.1 to 0.2 mbar.

 Ensure that the system is full of water & vented.

 That precautions have been taken to

prevent corrosion.

USER GUIDE

 A Carbon Monoxide detector is correctly

installed in the same room as the appliance.

WARNING: An over drawing chimney can

cause over firing, resulting in damage to the

appliance.

Ensure that you have read and understood

these instructions before lighting the fire.

Do not light the fire if is is suspected that any

part of the system could be frozen.

Always wear suitable protective fire gloves

when refuelling your stove, such as the Arada

glove supplied with your stove.

We recommend that you light a small fire for

the first few days of use to cure the paint and

allow the castings to relax. It is normal to

experience some odours whilst the paint cures.

These are non-toxic and temporary.

AIR INLET CONTROLS

Your stove has three air inlet controls. These

are located either on the stove body or the

door.

The primary air inlet provides under draught to

the base of the fire chamber , the

airwash system (secondary air) providing

overdraught and the ‘Easy Boost’ provides an

on demand increase of air for combustion.

PRIMARY AIR

The primary air is supplied through the

thermostatically controlled air inlet beneath

an access cover on left side of your stove. This

should have been calibrated when the stove

was installed. (See accompanying installation

guide). It regulates the amount of under

draught air entering the stove depending on the

setting of the control knob.

The control knob is numbered 0 to 5 relating to

the nominal temperature of the water within the

boiler jacket.

With a correctly configured installation the water

in the jacket should not exceed 80ºc when the

knob is set to 5.

If a lower radiator temperature is required a

lower number should be selected. Some

experimentation may be necessary to find the

setting best suited to your requirements.

The airwash has an internal sliding plate with

slots, housed in a cover plate, and is located

above the fire door. Sliding the control knob to

the RIGHT as far as it will go, achieves the fully

open position.

USER GUIDE

Wet Stove User Guide

Setting is

indicated by

screw

Sliding it to the LEFT will shut off the air inlet

slots .

EASY BOOST

BURNING WOOD



this.

 The use of two or three fire lighters may assist

to light the kindling.

 Set the airwash and easy boost controls to

the fully open position.

 Light the fire.

 After the kindling has caught light, you

should leave the fire door ajar by about

20mm. This will aid flue draw.

 The flue draw should be established after

five minutes, and the kindling reduced to

form an ember bed.

 Carefully load the stove with well seasoned

wood and close the fire door.

 After ten to fifteen minutes, regulate the

airwash control, typically reduce to

approximately half way.

 Close the easy boost air control.

BURNING SOLID FUELS

 Set the airwash to one quarter open.

 Set the easy boost air inlet to fully open.

 Light as with wood, with kindling and fire

lighters.



about five minutes, carefully load the

stove with fuel and close the door.

 When the fire is well alight close the easy

boost slider and then regulate the burning

rate by thermostat control.

 The airwash should be opened sufficiently

to keep the door glass clean.

Whilst burning solid fuel it can be beneficial to

occasionally riddle the grate bars so any burnt

USER GUIDE

Wet Stove User Guide

USER GUIDE

fuel will fall between the grate bars into the

ash pan below. This will ensure a good under

draught is maintained.

This is done by rotating back and fourth the

riddling lever on the side of the stove. The

operating tool supplied with the stove should

be used for this purpose.

WARNING: Properly installed, with a suitable

flue or chimney, operated and maintained

correctly, this appliance will not emit fumes

into the dwelling.

Occasional fumes when de-ashing and

refuelling may occur. However, persistent

fume emission is potentially dangerous and

must be investigated by a HETAS registered

installer.

Stop using the appliance if you smell fumes or

see smoke escaping.

actions should be taken:

 Open doors and windows to ventilate room.

 Check for flue or chimney blockage, and

clean if required.

Seek expert advice from your HETAS registered

installer. Do not attempt to re-light the fire until

and corrected.

MULTI FUEL GRATE

of reciprocating cast iron bars seated on a

pivoted comb. These should come

pre-assembled in your new stove.

All bars in the grate are identical, but every

other bar is turned though 180 degrees, with

the ends of the bars marked ‘H’ sitting on the

high sections of the comb, and the ends

marked ‘L’ sitting on the low sections.

The riddling lever, either on the side or front of

the stove with the door

closed and stop once red embers begin to fall

into the ash pan.

of the

DOOR GLASS

The door glass should remain clear during

normal burning. However, under certain

conditions, such as burning at a low rate, using

damp wood or overnight burning, the glass

may become

the appliance at a fast rate.

Alternatively when the stove is cold, open the

door and clean the inside face of the glass

with a damp cloth or with glass cleaner

(available from stove stockists and online at

www.aradastovesandspares.com).

6 Wet Stove User Guide

USER GUIDE

7Wet Stove User Guide

REDUCED BURNING

When wood is burnt slowly in a closed

appliance, it produces moisture and tar,

which will create condensation and deposits

in the chimney. This effect can be minimised

by burning hard for a short period, fifteen to

twenty minutes, twice a day. The easy boost

air inlet can be used to achieve this faster

burn rate. Remember to close the easy boost

inlet afterwards as this overrides the stoves

automatic thermostatic control.

Please Note: To avoid chimney problems your

appliance should not be burnt at a reduced

burn rate without a period of fast burning.

OVER FIRING & CHIMNEY FIRES

DO NOT over fire your appliance. Firing the

stove at maximum for prolonged periods may

result in over-firing. If the chimney connector

or casing glows red the appliance is being

over-fired and this may result in a chimney fire.

ASH REMOVAL

The appliance will require ash to be removed

periodically but an ash bed of approximately

20mm (3/4”) should be maintained. Care

must be taken not to burn hands or household

objects with falling embers.

The ash pan should be emptied when the

level of ash reaches the top of the ash pan.

On no account should the ash be allowed to

build up to touch the underside of the grate

bars, as this will greatly reduce the life span of

the grate. The ash will require less frequent

removal when burning wood than solid fuels.

WARNING: The ash can be very hot. Empty only

into a metal container. Even if the ash

and could easily start a fire or cause an injury.

Maintenance

FEDS INSPECTION (WHERE FITTED)

The Flue Exhaust Diversion (FEDS) system needs

to be checked regularly to ensure any build up

of ash and other debris is removed. The

Installation Guide contains details on how to

remove and inspect the outer feds plate. This

should be done only when the stove is unlit and

cold.

THERMOSTAT MAINTANENCE

It is possible that over time, especially if ash is not

removed regularly, the primary air inlet and its

damper flap may become restricted / blocked

by ash which may compromise the correct op-

eration of the thermostat.

The installation guide contains details on how to

maintain the operation of the damper flat and

thermostat housing.

MAINTENANCE

8 Wet Stove User Guide

SUMMER STORAGE / NON USAGE

Please ensure that your stove is left clean and moving components are well lubricated for the

summer months (during periods of prolonged non-use). If possible store the FEDS plate outside of

the stove. Check all moveable components at regular intervals, to ensure they are moving freely.

Allow air movement through the stove, by opening the airwash and primary air inlet control(s) to

about half way, open or leave the door ajar. This will allow a free flow of air through the appliance

maintenance will ensure your stove stays in the best condition for the coming winter months.

ADJUSTING THE DOOR HINGES

Once the appliance has been under fire for a period of time the fire door may appear to have

moved out of alignment with relation to the door aperture or catch. This is quite normal and due to

the settling of the casting.

The fire door can be re-aligned as follows:

 When the appliance is cold, open the fire door so that it is at right angles to the front of the

stove.

 Lift the fire door up off its hinges.

 Gently tap the hinge pins to compensate for the misalignment.

 Re-fit the door and check to ensure it now sits square to the body; if not repeat the above

steps.

If the fire door needs to be raised, please follow:

 Lift the fire door up off the hinges.

 Drop one washer on the top and bottom hinge pins. Fit the door and check.

REPLACEMENT PARTS

As a leading manufacturer we are conscious of being

able to support all our stove users with the supply of spare

parts to ensure your continued enjoyment and

list of

spares and consumables such as liners, grate bars and

throat plates as well as items to enhance its visual

appearance and efficiency such as Arada anthracite

stove paint and rope kits.

or online direct from Arada at:

www.aradastovesandspares.com

Wet Stove User Guide 9

GUARANTEE

When you buy a Hamlet Solution Boiler stove, you are not only buying a first class appliance you are

buying a commitment from us to look after you and your appliance for as long as you want.

All Hamlet Solution Boilers will have a three year guarantee as standard. This guarantee applies to

stoves fitted in the same country as its purchase. Stoves brought through the internet in the UK and

then taken abroad will not be eligible for any guarantee.

All guarantees apply to the body of the fire, i.e. the steel carcass and items fixed immovably

thereto.

Arada Ltd, cannot guarantee items which are susceptible to breakage or damage through careless

handling, dropping etc., or through misuse of the appliance by over firing, burning petroleum coke,

etc. Nor can the guarantee be extended to deterioration of parts through fair wear and tear.

Firebox linings, grate bars, fuel retainer, FED (throat plate), gasket material and door glass are

therefore not covered by the guarantee. The external paint finish and thermostat carry a one year

guarantee only.

The guarantee is conditional upon the appliance being installed, serviced and checked annually by

a qualified heating engineer, with documentation to be retained and produced in the event of a

claim being made.

Claims are not valid where installation does not conform to appropriate building regulations.

THE USE OF SPARES OTHER THAN THOSE SUPPLIED BY ARADA LTD WILL INVALIDATE THE GUARANTEE.

If your appliance proves to be defective as a result of faulty materials or workmanship during the

guarantee period, we will repair or replace it free of charge as long as the fire has been installed

according to the manual instructions and the installation is signed by a suitably qualified engineer at

the time of installation. All guarantee periods commence on the date of purchase and are

non-transferable.

Our guarantee is offered as an addition to your statutory rights. For users without access to the

internet please call 01297 35700 for further assistance.

If you think your fire is not working correctly or in the event of a breakdown, in the first instance

contact your local retailer or installer for assistance.

Solution 9 HSB9 4.5 7.5 9 570 221/2

Solution 12 HSB12 6 9.5 12 603 233/4

Solution 16 HSB16 8 13 16 603 233/4

Technical Information

Description

Height

mm inches

Solution 9 Inset HSB9-INSET 4 7 9 590 231/4

Solution 12 Inset HSB12-INSET 5 9 12 590 231/4

Description

Height

mm inches

Inset Models

Freestanding Output to

Room

Output to Water

Wood Solid

kW kW

Product Code

1 kW = 3,420 BTU

Output to

Room

Output to Water

Wood Solid

kW kW

Boiler Tapping Positions

Solution 9 HSB9 260 288 255 356

Solution 12 HSB12 328 325 252 425

Solution 16 HSB16 326 324 252 422

Description Product Code A B C D

Solution 9 Inset HSB9-INSET 165 49 139 172 345

Solution 12 Inset HSB12-INSET 165 49 139 172 345

Description Product Code F G H I K

Andere Handbücher für Hamlet

Inhaltsverzeichnis

Andere Arada Kessel Handbücher

Arada

Arada BK595 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung