Arbor Technology VA80140 Bedienungsanleitung

Materials Include:

Installation & Mounting Instructions

Arbor Mounting System

1. Read instructions carefully before assembling.

2. Identify each component from material list.

3. In the event of missing or defective parts, Please call our

customer service department at 1-800-282-9346 (ex.#20).

General Information:

1. Cordless Drill

2. Spirit Level

3. Tape Measure

Tools Required:

4 Galvanized Steel Surface Mounts

4 Plastic Mounting Sleeves

4 Bolts & Wing Nuts

4 White Stainless Screws

16 1/4” x 2 3/4” Cement Screws with Drill Bit

(3/16”, Minimum 3” Long)

31 2

Ground Mount Surface Mount

Materials Include:

4 Galvanized Steel Ground Augers

4 Plastic Mounting Sleeves

4 Bolts & Wing Nuts

4 White Stainless Screws

1 Steel Turning Rod

Refer to your arbor instructions

for exact dimensions between

posts. Measure out and mark on

the ground each post location.

Double check your spacing

before continuing.

Turn the auger using the turning

rod and apply even downward

pressure. For dry or hard ground,

use water to soften the ground

first.

As you turn the auger into the

ground, check with your level

to ensure it is straight. Do this

at least twice before you have

completely installed the mount.

Additional Hardware Required:

64 5

Once the ground stop (see sketch

3 below) is at ground level, the

mount is completely installed.

Slide the plastic sleeve over the

steel mount until the bottom rests

on the ground stop.

Line up the holes in the plastic

sleeve and steel mount. Take a

bolt and wing nut (included) and

insert it into the hole until it is

firmly in place. Repeat steps 2

to 5 for the remaining mounts.

Once you have installed and

verified the orientation of each

mount, set your arbor posts onto

the mounts and push down to

ground level. Using one of the

screws provided, secure the

bottom of each post to the

mounts as shown.

If you have questions concerning the installation of this product and require assistance, please call our

Customer service department at 1-800-282-9346 (ext.#20), weekdays from 8:00 am. to 4:00 pm. EST.

If you have comments or suggestions about this product, let us know! Call: 1-800-282-9346 (ext.#24).

Thank you for purchasing the “Arbor Mounting System”.

Questions ? :

1. For installation of the surface mounts on concrete, use drill bit (not provided) to drill pilot holes.

Fasten each mount in place using cement screws (not included).

2. For installation of the surface mounts on wood or a similar surface, use wood screws (not included).

3. Basic identification sketch of each part:

Additional Information:

Plastic Sleeve

(3 1/2” , 4” or 5”)

Steel Surface

Mount

Steel Ground

Auger

Steel Turning Rod

Ground Stop

12 3

Bolt &

Wing Nut

Dieses Handbuch passt für folgende Modelle

Andere Arbor Technology Rasen- und Gartengeräte Handbücher

Arbor Technology

Arbor Technology Garden Pergola Build Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung