Arbor Technology EPIC-747E Bedienungsanleitung

EPIC-747E

Wide Range Temperature

EPIC Compact Board

User’s Manual

Version 1.0

2012.09

This page is intentionally left blank.

- i -

Index

Contents

Chapter 1 - Introduction............................................ 1

1.1 Copyright Notice.........................................................2

1.2 Declaration of Conformity..........................................2

1.3 About this User’s Manual...........................................3

1.4 Warning .......................................................................3

1.5 Replacing the Lithium Battery...................................4

1.6 Technical Support.......................................................4

1.7 Warranty ......................................................................4

1.8 Packing List.................................................................5

1.9 Ordering Information..................................................5

1.10 Specications ...........................................................6

1.11 Board Dimensions ....................................................7

Chapter 2 - Installation.............................................. 9

2.1 Block Diagram...........................................................10

2.2 Jumpers and Connectors ........................................11

Jumpers............................................................................13

JRS1: COM2 RS-232/422/485 Mode Selection.....13

JBAT1: Clear CMOS Setting..................................14

JVLCD1: LCD Panel Voltage Selection ................16

JAT1: AT/ATX Power Mode Selection...................17

Connectors.......................................................................18

IDE1: IDE Connector..............................................18

COM2~5: Serial Port Connectors .........................21

AUDIO1: AUDIO Connector...................................22

JCOM1: RS-422/485 Output Connector ...............23

USB1~2: USB Connectors.....................................24

EKBMS1: Keyboard & Mouse Connector ............25

VGA1: Analog RGB Connector.............................26

LVDS1: LVDS LCD Connector...............................27

COM1: Serial Port Connector ...............................28

INV1: LCD Inverter Connector ..............................29

LAN1~2: Gigabit Ethernet Connectors ................30

- ii -

USB3~4: USB Connectors.....................................31

DIO1: Digital IO Connector....................................32

JFRT1: Switched and Indicators ..........................33

MINIPCI1: Mini PCI slot..........................................34

MC1: Mini-Card Slot...............................................35

JBATT1: External Battery Connector...................36

SIM1: SIM card Socket...........................................37

SATA1: Serial ATA Connectors .............................38

12VIN1: +12V Connector .......................................39

SAPO1: Small 4P Power Connector.....................40

2.3 The Installation Paths of CD Driver.........................41

Chapter 3 - BIOS......................................................43

3.1 BIOS Introduction.....................................................44

3.2 Advanced Settings ...................................................46

3.2.1 CPU Conguration.......................................47

3.2.2 IDE Conguration ........................................48

3.2.3 Super IO Conguration ...............................50

3.2.4 Hardware Health Conguration ..................51

3.2.5 USB Conguration.......................................52

3.3 Advanced Chipset Settings .....................................53

3.3.1 North Bridge Chipset Conguration ..........54

3.3.2 South Bridge Chipset Conguration..........56

3.3 Advanced PCI/PnP Settings.....................................58

3.4 Boot Settings ............................................................59

3.4.1 Boot Settings Conguration .......................60

3.5 Security......................................................................61

3.6 Exit Options...............................................................63

Appendix ..................................................................65

Appendix-A I/O Port Address Map ................................66

Appendix-B Interrupt Request Lines (IRQ) ..................69

Appendix-C BIOS memory mapping.............................70

Appendix-D Watchdog Timer (WDT) Setting................71

Appendix-E Digital I/O Setting.......................................72

Index

- 1 -

Introduction

1Chapter 1

Introduction

Chapter 1 - Introduction

- 2 -

Introduction

The information in this document is subject to change without prior notice in

order to improve the reliability, design and function. It does not represent a

commitment on the part of the manufacturer.

Under no circumstances will the manufacturer be liable for any direct, indirect,

special, incidental, or consequential damages arising from the use or inability

to use the product or documentation, even if advised of the possibility of such

damages.

This document contains proprietary information protected by copyright.

All rights are reserved. No part of this manual may be reproduced by any

mechanical, electronic, or other means in any form without prior written

permission of the manufacturer.

1.1 Copyright Notice

The CE symbol on your product indicates that it is in compliance with the

directives of the Union European (EU). A Certicate of Compliance is available

by contacting Technical Support.

This product has passed the CE test for environmental specications when

shielded cables are used for external wiring. We recommend the use of

shielded cables. This kind of cable is available from ARBOR. Please contact

your local supplier for ordering information.

This product has passed the CE test for environmental specications. Test

conditions for passing included the equipment being operated within an

industrial enclosure. In order to protect the product from being damaged by

ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the

use of CE-compliant industrial enclosure products.

Warning

This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

FCC Class A

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in which case the user will be required to correct the interference at his own

expense.

1.2 Declaration of Conformity

- 3 -

Introduction

1.3 About this User’s Manual

This User’s Manual is intended for experienced users and integrators with

hardware knowledge of personal computers. If you are not sure about any

description in this User’s Manual, please consult your vendor before further

handling.

1.4 Warning

Single Board Computers and their components contain very delicate

Integrated Circuits (IC). To protect the Single Board Computer and its

components against damage from static electricity, you should always follow

the following precautions when handling it :

1. Disconnect your Single Board Computer from the power source when you

want to work on the inside.

2. Hold the board by the edges and try not to touch the IC chips, leads or

circuitry.

3. Use a grounded wrist strap when handling computer components.

4. Place components on a grounded antistatic pad or on the bag that came

with the Single Board Computer, whenever components are separated

from the system.

RoHS

ARBOR Technology Corp. certies that all components in its products are

in compliance and conform to the European Union’s Restriction of Use of

Hazardous Substances in Electrical and Electronic Equipment (RoHS)

Directive 2002/95/EC.

The above mentioned directive was published on 2/13/2003. The main

purpose of the directive is to prohibit the use of lead, mercury, cadmium,

hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated

diphenyl ethers (PBDE) in electrical and electronic products. Member states

of the EU are to enforce by 7/1/2006.

Declaration of SVHC / REACH Conformity

To minimize the environmental impact and take more responsibility to the

earth we live, Arbor hereby conrms all products comply with the restriction

of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH

--Registration, Evaluation, Authorization, and Restriction of Chemicals)

regulated by the European Union.

All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- 4 -

Introduction

1.7 Warranty

This product is warranted to be in good working order for a period of two years

from the date of purchase. Should this product fail to be in good working order

at any time during this period, we will, at our option, replace or repair it at no

additional charge except as set forth in the following terms. This warranty

does not apply to products damaged by misuse, modications, accident or

disaster.

Vendor assumes no liability for any damages, lost prots, lost savings or any

other incidental or consequential damage resulting from the use, misuse of,

or inability to use this product. Vendor will not be liable for any claim made by

any other related party.

Vendors disclaim all other warranties, either expressed or implied, including

but not limited to implied warranties of merchantibility and tness for a

particular purpose, with respect to the hardware, the accompanying product’s

manual(s) and written materials, and any accompanying hardware. This

limited warranty gives you specic legal rights.

Return authorization must be obtained from the vendor before returned

merchandise will be accepted. Authorization can be obtained by calling or

faxing the vendor and requesting a Return Merchandise Authorization (RMA)

number. Returned goods should always be accompanied by a clear problem

description.

1.5 Replacing the Lithium Battery

Incorrect replacement of the lithium battery may lead to a risk of explosion.

The lithium battery must be replaced with an identical battery or a battery type

recommended by the manufacturer.

Do not throw lithium batteries into the trash-can. It must be disposed of in

accordance with local regulations concerning special waste.

1.6 Technical Support

If you have any technical difculties, please do not hesitate to call or e-mail

our customer service.

http://www.arbor.com.tw

E-mail:info@arbor.com.tw

- 5 -

Introduction

1.8 Packing List

1.9 Ordering Information

Packing List

Before you begin installing your single board, please make sure that the

following materials have been shipped:

1 x EPIC-747E EPIC Compact Board with heat sink

1 x Power cable

1 x Driver CD

1 x Quick Installation Guide

If any of the above items is damaged or missing, contact your vendor im-

mediately.

EPIC-747E Intel Atom™ N455 1.6GHz Wide range

temperature EPIC Compact Board

CBK-11-2902-00

Cable Kit

1 x Audio Cable

4 x COM Port Cables

1 x IDE Cable

1 x KB & MS Cable

2 x SATA Cables

2 x USB Cables

- 6 -

Introduction

1.10 Specications

Form Factor EPIC Compact Board

CPU Soldered onboard Intel®Atom N455 1.6GHz processor

Chipset Intel®ICH8M

System Memory Soldered onboard DDR3 2GB SDRAM

Display

Integrated Intel®Graphics Media Accelerator 3150,

Analog RGB/ Single Channel 18-bit LVDS/ Dual

Independent Display

Ethernet 2 x Realtek RTL8111E PCIe Gigabit Ethernet

controllers

I/O Chip Winbond 83627UHG

BIOS AMI PnP Flash BIOS

Audio Realtek ALC886 7.1 Channel HD Audio Codec, Mic-in/

Line-out

Storage

2 x SATA ports at 300MB/s HDD transfer rate

1 x Ultra ATA, supporting 2 IDE devices

Soldered onboard 2GB NANDrive

Serial Port 5 x COM ports (COM1, COM3, COM4, COM5: RS-232,

COM2: RS-232/422/485 selectable)

KBMS 1 x 6-pin wafer connector for Keyboard and Mouse

(PS/2 interface via cable)

Universal Serial

Bus 8 x USB 2.0 ports

Digital I/O 8-bit programmable Digital Input/Output

Expansion Inter-

face

1 x Mini-card Socket

1 x Mini-PCI Socket

1 x SIM Socket

Operation Temp. -40oC ~ 85oC (-40oF ~ 185oF)

Watchdog Timer 1~255 levels Reset

Dimension

(L x W) 165 x 115 mm (6.5” x 4.5” )

Inhaltsverzeichnis

Andere Arbor Technology Hauptplatine Handbücher

Arbor Technology

Arbor Technology EmETXe-i91M0 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i2701 Bedienungsanleitung

Arbor Technology

Arbor Technology PBE-1000 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i2705D Bedienungsanleitung

Arbor Technology

Arbor Technology EmCORE-i55M0 Bedienungsanleitung

Arbor Technology

Arbor Technology EmCORE-i2305 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i45M2 Bedienungsanleitung

Arbor Technology

Arbor Technology PBE-1702 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i87H0 Bedienungsanleitung

Arbor Technology

Arbor Technology MB-i77Q0 Bedienungsanleitung

Arbor Technology

Arbor Technology MB-i965Q Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i89H0 Bedienungsanleitung

Arbor Technology

Arbor Technology EmETX-a5363 Bedienungsanleitung

Arbor Technology

Arbor Technology MB-i77Q0 Bedienungsanleitung

Arbor Technology

Arbor Technology Em104P-i2904 Bedienungsanleitung

Arbor Technology

Arbor Technology HiCORE-i6320 Bedienungsanleitung

Arbor Technology

Arbor Technology MB-i35Q1 Bedienungsanleitung

Arbor Technology

Arbor Technology EmETXe-i87M0 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i92QA Bedienungsanleitung

Arbor Technology

Arbor Technology HiCORE-i35Q Bedienungsanleitung

Arbor Technology

Arbor Technology EmCORE-i2702 Bedienungsanleitung

Arbor Technology

Arbor Technology HiCORE-i67Q1 Bedienungsanleitung

Arbor Technology

Arbor Technology EmCORE-i315 Bedienungsanleitung

Arbor Technology

Arbor Technology ITX-i9453 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung