Archtek 5634PCV Bedienungsanleitung

5634 PCV

User’s Manual

Table Contents

Table Contents..........................................................................................2

Chapter 1 Installation..............................................................................3

1. 1 Checking your components......................................................3

1. 2 What else you need..................................................................3

1. 3 Removing the computer cover..................................................3

1. 4 Inserting the modem.................................................................4

1. 5 Connecting to the telephone line..............................................5

1. 6 Connecting to your telephone...................................................5

1. 7 Verifying your connection .........................................................6

1. 8 Windows 95/98 Modem Driver Installation ( PnP)....................7

1. 9 Windows NT4.0 Modem Driver Installation ..............................8

1.10 Linux Red Hat 6.0 Modem Driver Installation .........................8

1.11 MS-DOS Modem Driver Installation ........................................9

Chapter 2 AT commands set ................................................................11

2. 1 Data Mode Command ............................................................11

2. 2 Result Code............................................................................23

2. 3 S Registers Definitions...........................................................25

2. 4 Class 1 Fax Commands.........................................................32

2. 5 Voice Commands ...................................................................35

2. 6 AT% TTn Commands.............................................................37

Chapter 1 Installation

Chapter 1 provides detailed instructions for installing your modem.

1.1 Checking your components

Unpack your components and make sure you have the following items:

lThe modem.

lA modular telephone cable to connect your modem to the telephone line.

lThis user's manual.

lCommunication software and manual.

When you open your package, make sure all of the above items are included

and not damaged. If you see that any components are damaged, please notify

your dealer immediately.

1.2 Installing the modem

The following instructions explain how to install the modem in a IBM

compatible type personal computer. If you will be installing the modem into a

different computer, refer to the manual that accompanied your computer or

contact your computer dealer for instructions on installing the modem in your

personal computer.

1.3 Removing the computer cover

Turn off the personal computer's power. No power must be applied to your

computer when you install the internal modem and computer could be

damaged.

Make sure you can freely access the back of the personal computer.

Unscrew the necessary screws to loosen the computer cover. Then set the

screws in a safe place and remove the computer cover.

1.4 Inserting the modem

The internal modem can fit into any available PCI slot in your personal

computer. To insert the internal modem in your personal computer:

1. Position yourself so that you can easily access the computer's expansion

slots.

2. Select any available half-card slot into which you can install the internal

modem.

3. Remove any slot cover that may be over the slot. Then remove the slot

cover and keep both in a safe place (you will need the screw to secure the

internal modem and you may need the slot cover if you decide to remove

the internal modem in the future).

4. Hold the internal modem above the slot you selected, making sure the

modem's edge connectors are pointing down toward the base of the

personal computer (see Figure1-1).

5. Carefully slide the modem into the PCI slot, applying even pressure to both

ends of the modem. Stop inserting the modem when its gold-plated edge

connectors are aligned with and completely fit into the base of the

computer.

6. If you removed a screw from the slot cover, use that screw to secure the

modem in the PCI slot. You may want to test the modem's telephone

connection (described in the next section) before securing your modem.

7. Use the cover-mounting screws to secure the computer cover.

Figure 1-1. Inserting the modem

1.5 Connecting to the telephone line

Use the following procedure to connect your modem to the telephone line:

1. Make sure you have an RJ-11 telephone jack. If you need a modular jack,

either obtain a telephone adapter from a telephone or electronics store and

follow the installation instructions provided with the adapter, or have your

local telephone company replace your existing telephone jack with a

modular-type jack and your existing telephone cord with a modular cord.

2. Unplug your telephone's cable from the wall jack.

3. Take one end of the modular telephone cable supplied with the modem

and plug it into the LINE modular telephone jack on the back of the modem

(see Figure 1-2).

4. Plug the other end of the telephone cord into the telephone jack on the wall,

as you would any modular telephone.

1.6 Connecting to your telephone

Your modem is so convenient, it provides a second modular telephone jack

that lets you connect your telephone to the same telephone line the modem is

using. This lets you manually dial data calls or make voice calls when you are

not using your modem.

Use the following procedure to connect your telephone to your modem:

Connect the telephone's modular cord into the PHONE jack on the back of

your modem (see Figure 1-3).

Lift your telephone's handset and listen for a dial tone.

LINE

PHONE

5634PCV

Figure 1-2. Back of the modem

1.7 Verifying your connection

Before you proceed to next step, make sure your connection matches the one

shown in Figure 1-3.

MODEM CARD

PHONE

JACK

LINE

PHONE

5634PCV

Figure 1-3. Completed modem installation

If you connected the modem to a computer, place the computer into terminal

mode and complete the configuration information required by the software.

Refer to your computer manual to find out the appropriate command to use.

Then use the following procedure to verify that your connections:

1. Type ATand press the Enter key. If your system is operating properly, your

modem sends an OK response to your screen and wait for your next

command.

If you did not receive a response, make sure your computer is sending

commands to your modem. If this does not solve your problem, contact

your computer dealer.

2. Use your communication software to prepare your computer to dial a call.

Then type AT D x phone number, where x is either T for touch-tone

dialing or Pfor pulse dialing and phone number is the telephone number

that your modem is using.

For example, if your modem is connected to the telephone line 555-2121

and Touch-Tone dialing is supported in your calling area, type ATDT

5552121.

3. Press the Enter key. You should receive a BUSY response and you should

hear the busy signal through the modem speaker because the modem is

calling itself.

Your modem is now ready for operation. Refer to the manual that came with

your communication software to begin communications. If you will be

communicating directly with your modem, or if you want to find out more about

the modem's operation, proceed to Chapter 2.

1.8 Windows95/98

ModemDriver Installation(PNP)

1. Install the PnP modem into an available slot.

2. Turn On your computer.

3. As you enter Windows you should receive a message saying “PCI

communication Device”, than “5634PCV V90 modem”.

4. Windows will identify the modem and then present you with three

choices.

Do not install a driver

Driver from disk provided by manufacturer

Select from a list of alternate drivers.

Select Driver from disk provided by manufacturer. Windows will ask

you to insert your disk. Put the disk in your drive and select right inf

file then hit OK. You will be presented with a listing of Topic modems.

Select the model number of your modem and then hit OK.

5. Click Finish and Windows will install the driver, and then finish

booting.

6. To check the modem installation open Control Panel and then

Modems. Click on the Diagnostics tab. Click on the port which lists

your modem. Click on More Info. Your modem should report back

with modem information. Your modem is functioning properly.

1.9 Windows NT 4.0 Modem

Driver Installation

1. Install the PnP modem into an available slot.

2. Insert Setup program for Windows NT drivers’ disk into drive A or B.

3. Execute the “Setup”program to install the PCI agent driver.

4. Then, after the installation is completed, reboot PC.

5. After PC is rebooted and NT is running, follow the steps described in

section 1.1 to add the modem and its drivers.

NOTE: Microsoft does not support plug and play in Windows NT 4.0.

1.10 Linux Red Hat 6.0

Modem Driver Installation

A. Manual mode:

1. At path /proc, find file pci then use vi editor to find Topic vender ID “151f”

and the

I/O-address, IRQ-number Linux assign to Topic modem.

For example : cd /proc

vi pci

…………………………………………

Vendor id=151f. Device id=0.

Medium devsel. IRQ=5.

I/O at 0xe400 [0xe401].

(type :q to quit vi)

2. At path /dev, use setserial tty-number uart 16550A irq IRQ-number port I/O-

address

For example : setserial ttyS2 uart 16550A irq 5 port 0xe400

3. At path /dev, remove default modem link then link modem to the tty you

assign in step 2

For example : rm modem

ln –s ttyS2 modem

4. Now, you can use minicom to test the modem by type ATI3 to make sure the

modem is Topic modem.

For example : minicom

………………..

ATI3

B. Automatic Mode

1. Copy topic.modem excutable file to /bin

2. Copy script file rc.serial to /etc/rc.d

3. When Linux boot again you can see the message " Setup topic modem …"

or you can run topic.modem directly.

4. You can use minicom to check Topic modem.

1.11 MS-DOS Modem

Driver Installation

Introduction

This program intends to provide the function for hardware resource

configuration via 5634PCV internal modem card. It is only can be executed in

DOS environment, Windows DOS prompt is inhabited to run this program.

Installation

Prior launching the program, 5634PCV PCI modem card must be installed in

the PC in advance. Besides, it can be used to configure the multiple PCI cards.

Configuration

When the program is launched, it will search the 5634PCV PCI card first. If no

card is found, an error message will be shown and the program will be

terminated. If only one card is enumerated, a configuration dialog window will

be popped up immediately. User can set and the IO port address and interrupt

number of PCI card in this configuration dialog. After setting, user may select

‘OK’button to set the desired setting to PCI card and exit the program. If user

selects‘Cancel’button, the changed setting will not be effective. Please note

the changed setting will not be stored and saved in PC BIOS or PCI card after

PC is rebooted.

When‘OK’button is selected, the program will automatically test the IO port

and interrupt number to see whether the PCI card can be operated normally

with the desired setting. If either IO or IRQ verification is failed, the program

will pop up a warning message and let user to set another value.

If multiple cards are detected, the program will show a list box to demonstrate

the found cards in the sequence (i.e., modem1, modem2...modemN). Then

that, user may select any one of the modem from the list to configure.

Diagnosis

There is push button‘Diagnose’existed in the configuration dialog. When this

button is selected, the program will issue some‘AT’commands to modem and

display the result for analysis. Before sending the command to UART of PCI

card, the program will first verify the IO and interrupt setting. If the verification

is failed, it will stop the diagnosis and prompt a waning message to the screen.

After the diagnosis is done, it will show the PCI information, including device ID,

vendor ID, subsystem ID and subsystem vendor ID. Moreover, the version

number and built date of modem controller and DSP code will be shown as

well.

Command Line

This program also provides the function to set IO and interrupt number in the

command line operation. Two optional arguments are defined as follows:

-io <I/O window address, e.g. 0x240,0x300...>

-int <Hardware interrupt number, e.g. 3,4,5...>

When any one of the arguments is given when the program is run in DOS

command line, the program will assume the‘Command line’operation is

desired. Then that, it will not prompt the window interface and directly set the

IO and interrupt number of PCI card by the given value. After setting, the

program will be terminated immediately. Please note the both arguments must

be given in the same time. If any one of argument is missed, the program will

not set the value to adapter and the error message will be shown.

Inhaltsverzeichnis

Andere Archtek Modem Handbücher

Archtek

Archtek 5634RCS Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung