Argo Infrared Remote Controller for High-Wall fan... Bedienungsanleitung
INFRARED REMOTE CONTROLLER
FOR HIGH-WALL FAN COILS
USER MANUAL
Read this manual carefully before using the remote controller and keep it for future
reference.
If this manual is lost, consult the electronic version on the argoclima.com website.
Argoclima reserves the right to make any changes to this document due to possible
product improvements without prior notice.
V 11/20
Preface
For correct installation and operation, please read all instructions carefully. Before
reading the instructions, please be aware of the following items:
(1) For the safe operation of this unit, please read and follow the instructions
carefully.
(2) During operation, total capacity of indoor units should not exceed the total
capacity of outdoor units. Otherwise, poor effect of cooling or heating may result.
(3) Direct operators or maintainers should well keep this manual.
(4) If this unit fails to operate normally, please contact our service center as soon
as possible and provide the following information:
1) Content on the nameplate (model number, cooling capacity, production code,
ex-factory date).
2) Malfunction details (before and after the malfunction occurs).
(5) Each unit has been strictly tested and proved to be qualified before ex-factory.
In order to prevent units from being damaged or operating normally because of
improper disassembly, please do not disassemble the unit by yourself. If you need to
disassemble and check units, please contact our service center. We will send
specialists to guide the disassembly.
(6) All graphics in this manual is only for your reference. For sales or production
reasons, these graphics are subject to change by manufacturer without prior notice.
Contents
1 RRemote Controller .......................................................................................11
1.1 Button name and function introduction ................................................................11
1.2 Preparation before operation ............................................................................. 12
1.3 Introduction of operation function ....................................................................... 13
1.4 Introduction of special functions ......................................................................... 16
1.5 Replacing batteries in remote controller and notes ............................................ 177
Infrared Remote Controller for High-Wall fan coils
11
1 RRemote Controller
1.1 Button name and function introduction
12
No.
Button name
Function
1
ONN/OFF TTurn on or turn off the unit
2
TTURBO SSet turbo function
3
MODE
SSet operation mode
4
SSet up &down swing status
5
I FEELL SSet I FEEL function
6
TEMP SSwitch temperature displaying type on the units display
77 SSet health function and air function
88 LIGHTHT SSet light function
9 XX-FANN SSet XX-FAN function
100 SLEEP SSet sleep function
11
CLOCKK SSet clock of the system
12
TT-OFF SSet timer off function
13
TT-ONN SSet timer on function
14
SSet left & right swing status
15
FANN SSet fan speed
16
/
SSet temperature and time
1.2 Preparation before operation
When using the remote controller for the first time or after replacing the batteries,
please set the time of the system according to current time in the following steps:
(1) Pressing CLOCK button, is blinking.
(2) Pressing or button, the clock time will increase or decrease rapidly.
(3) Press CLOCK button again to confirm the time and return to display current
time.
Infrared Remote Controller for High-Wall fan coils
13
1.3 Introduction of operation function
(1) Selecting operation mode
In unit on status, press MODE button to select operation mode in following
sequence:
(2) SSetting temperature
In unit on status, press button to increase setting temperature and press
button to decrease setting temperature. The range of temperature is from 16℃ to
30℃. Note: Under auto mode, manual adjustment of temperature is not needed.
(3) Adjusting fan speed
In unit on status, press FAN button to adjust fan speed in following sequence:
Notes:
①When operation mode changes, fan speed is memoried;
②Under dry mode, fan speed is low and can not be adjusted.
(4) Setting swing function
Setting left&right swing
button to adjust left&right swing
button to adjust left&right swing
1) Under simple swing status, press
status;
2) Under fixed-angle swing status, press
angle circularly as below:
Note: operate continuously left&right swing in 2 seconds, swing states will change
according to above-mentioned order, or switch closed state and state.
Setting up & down swing
1) Under simple swing status, press button to adjust up & down swing
status;
Infrared Remote Controller for High-Wall fan coils
14
2) Under fixed-angle swing status, press button to adjust up & down swing
angle circularly as below:
Note: operate continuously left & right swing in 2 seconds,swing states will change
according to above-mentioned order, or switch closed state and state;
(5) Setting turbo function
1) Under cool or heat mode, press TURBO button to set turbo function.
2) When is displayed, turbo function is on.
3) When is not displayed, turbo function is off.
4) When turbo function is on, the unit operates in super high speed to achieve
quick cooling or heating. When turbo function is off, the unit operates in setting fan
speed.
(6) Setting light function
The light on the receiver light board will display present operation status. If you
want to turn off the light, please press LLIGHT button. Press this button again to
turn on the light.
(7) Wiewing ambient temperature
1) In unit on status, receiver light board or wired controller is defaulted to display
setting temperature. Press TEMP button to view indoor or outdoor ambient
temperature.
2) When is displayed, it means the displayed temperature is setting
temperature.
3) When is displayed, it means the displayed temperature is indoor ambient
temperature.
4) When is displayed, it means the displayed temperature is outdoor
ambient temperature.
Note: setting temperature is always displayed in Remote Controller.
(8) Setting X-FAN function
1) In cool or dry mode, press X-FAN button to set X-FAN function.
2) When
3) When
is displayed, X-FAN function is on.
is not displayed, X-FAN function is off.
4) When X-FAN function is on, the water on the evaporator will be blown away
until turning off the unit to avoid mildew.
Infrared Remote Controller for High-Wall fan coils
15
(9) Setting health function
1) In unit on status, press button to set health function.
2) When
3) When
is displayed, health function is on. is not displayed,
health function is off.
4) Health function is available when the unit is equipped with anion generator.
When health function is on, the anion generator will start operation, adsorbing
the dusts and killing the bacteria in the room.
(10) Setting air function
1) Press button until is displayed, then air function is turned on.
2) Press button until is disappeared, then air function is turned off.
3) When the indoor unit is connected with fresh air valve, air function setting can
control the connection of fresh air valve, which can control the fresh air volume
and improve the air quality inside the room.
(11) Setting sleep function
(12) In unit on status, press SLEEP button to turn on or turn off sleep function.
2) When
3) When
is displayed, sleep function is on. is not
displayed, sleep function is off.
Notes:
①Sleep function can not be set in auto and fan mode;
②When turning off the unit or switching mode, sleep function is cancelled;
(12) Setting I FEEL function
(13) In unit on status, press I FEEL button to turn on or turn off I FEEL function.
2) When
3) When
is displayed, I FEEL function is on.
is not displayed, I FEEL function is off.
4) When I FEEL function is turned on, the unit will adjust temperature according
to the temperature detected by the remote controller to achieve the best air-
conditioning effect. In this case, you should place the remote controller within the
valid receiving range.
(13) Setting timer
YYou can set the operation time of unit as you need. You can also set timer on and
timer off in combination.
Infrared Remote Controller for High-Wall fan coils
16
Before setting, check if the time of the system is the same as the current time. If not,
please set the time according to current time.
1) Setting timer off
a. Pressing T-OFF button, “T-OFF”is blinking and time displaying one time displays
the timer time of last setting.
b. Press or button to adjust the timer time.
c. Press T-OFF button again to confirm setting. T-OFF is displayed and time
displaying one resumes to display current time.
d. Press T-OFF button again to cancel timer and T-OFF is not displayed.
2) Setting timer on
a. Pressing T-ON button, T-ON is blinking and time displaying time one displays the
timer time of last setting.
b. Press or button to adjust the timer time.
c. Press T-ON button again to confirm setting. T-ON is displayed and time
displaying zone resumes to display current time.
d. Press TT-ON button again to cancel timer and T-ON is not displayed.
1.4 Introduction of special functions
(1) Setting child lock
1) Press and button simultaneously to lock the buttons on remote
controller and is displayed.
2) Press and button simultaneously again to unlock the buttons on
remote controller and is not displayed.
3) If the buttons are locked, blinks 3 times when pressing the button and any
operation on the button is invalid.
(2) Switching temperature scale
In unit off status, press MODE button and button simultaneously to switch
temperature scale between ℃ and ℉.
(3) Setting energy-saving function
1) In unit on status and under cool mode, press CLOKC and TEMP button
simultaneously to enter energy-saving mode.
When is displayed, energy-saving function is on.
When is not displayed, energy-saving function is off.
Infrared Remote Controller for High-Wall fan coils
177
2) If you want to turn off the energy-saving function, press CLOCK and TEMP
button and is not displayed.
Note: energy-saving function is only available in cooling mode and it will be exited
when switching mode or setting sleep function.
(4) Absence function
1) In unit on status and under heat mode, press CLOCKK and TEMP button
simultaneously to enter absence function. Temperature displaying zone
displays and is displayed.
2) Press CLOCK and TEMP button simultaneously again to exit absence
function. TTemperature displaying zone resumes previous display and is not
displayed.
3) In winter, absence function can keep the indoor ambient temperature above
0℃ to avoid freezing.
Note: Absence function is only available in heating mode and it will be exited when
switching mode or setting sleep function.
1.5 RReplacing batteries in remote controller and notes
(1) Lift the cover along the direction of arrow (as shown in Fig 1①).
(2) Take out the original batteries (as shown in Fig 1②).
(3) Place two (AAA 1.5) dry batteries, and make sure the position of “polar +
and “-” polar is correct (as shown in Fig 2③).
(4) Reinstall the cover (as shown in Fig 2④).
Fig.1 Fig.2
Infrared Remote Controller for High-Wall fan coils
Inhaltsverzeichnis
Andere Argo Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
