Argus RST 48/30 Bedienungsanleitung

RST 48/30

Switched Mode Rectifier/Eliminator

010-006-B0

Argus Technologies Ltd. Visit www.argus.ca

Burnaby, British Columbia. Telephone: 604 436 5900 Fax: 604 436 1233

Argus Technologies reserves the right to make changes to the products and information contained in this document without notice.

Printed in Canada.

This page intentionally left blank.

RST 48/30 SWITCHED MODE

RECTIFIER/ELIMINATOR

#010-006-B0

SERIAL # ____________

The following documents and drawings are included in this manual to provide the necessary information required

for routine operation and fault diagnosis of the unit:

• Specifications RST 48/30: 010-006-B1 Rev B

• Warranty Policy: 048-507-10

• Installation and Operation Instructions: 010-002-C0 Rev H

• Main Parts List: 010-006-20

• Recommended Spare Parts List: 010-006-G0

• Main Schematic: 010-006-05

• Outline Drawing: 010-006-06

• Power Circuit Parts List: 700-015-20

• Power Circuit Schematic: 700-015-05 (Page 1)

• Front Panel Circuit Parts List: 700-075-20

• Front Panel Schematic: 700-075-05

• Factory Service Information: 048-527-10

ARGUS TECHNOLOGIES 010-006-B0 Rev A

SPECIFICATIONS FOR ARGUS TECHNOLOGIES’ SWITCHED MODE RECTIFIER MODEL RST 48/30

Output

Voltage: 42 to 62VDC (test)

50 to 60VDC (equalize)

48 to 57VDC (float)

Current: 30 Amps DC nominal

Power: 1698 Watts continuous

Regulation: +/-.02% Line and load (static)

1% deviation for 50 to 100% load step (dynamic)

Time Stability: .1% per year

Temp. Stability: 100ppm/degree C over the operating range

Response Time: 1ms to .1% of output for 50 to 100% load step

Noise: Less than 22dBrnc (Voice Band)

10mV rms to 10MHz (Wide Band)

EMI: The unit meets requirements of FCC Rules Part 15 Subpart J

Level A. The unit also meets Bell Canada’s design standard

DS-8465 (Electromagnetic Interference/Compatibility Requirements

and Test Methods for Telecommunications Systems and Equipment)

Section 4. as per Test Methods detailed in Section 6.

Breaker Rating: 60 Amp; 5,000 Amp interrupting capacity at 65VDC

In Accordance with FCC requirements, we provide the following statement as specified in the FCC guidelines for

conformance to Part 15 Subpart J, Level A:

WARNING: This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction

manual, may cause interference to radio communications. It has been

tested and found to comply with the limits for a Class A computing

device pursuant to Subpart J of Part 15 of FCC Rules, which are

designed to provide reasonable protection against such interference

when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference in which

case the user at his own expense will be required to take whatever

measures may be required to correct the interference.:WARNING

ARGUS TECHNOLOGIES 010-006-B1 Rev B Page 1 of 2

SPECIFICATIONS FOR ARGUS TECHNOLOGIES’ SWITCHED MODE RECTIFIER MODEL RST 48/30

Input

Voltage: 92 to 132VAC (57-63 Hz)

184 to 264VAC (47-63 Hz)

Current: 10.2 Amps (240VAC nominal) @ 1698 Watts

20.4 Amps (120VAC nominal) @ 1698 Watts

Power Factor: .90 Lagging 0-100% load

T.I.F.: Less than 120 at 100% load (current)

Efficiency: 88% min. 40-100% load

Hold-over Time: 30ms from loss of 240VAC line

Source Impedance: 5% inductive or resistive

Soft Start: 33% per second

Start Delay: 0-90 sec. (10 second increments)

Recommended Feeder Breaker: 30 Amps or greater (120VAC)

15 Amps or greater (240VAC)

Breaker Rating: 30 Amp; 10,000 Amp interrupting capacity at 250VAC (120VAC)

15 Amp; 10,000 Amp interrupting capacity at 250VAC (240VAC)

Miscellaneous

Acoustic Noise: 45dBa at three feet

Weight: 40 lbs (18.2 kg)

Size: 7.00”H x 17”W x 15” (17.7cm H x 43.2cm W x 38.1cm D)

Recommended Connection Wire Sizes (as per UL)

Ambient Temp=30 deg C Input: #12 AWG

Output: #10 AWG

Ambient Temp=50 deg C Input: #10 AWG

Output: #8 AWG

Environmental

Temperature: 0 to 50 deg. C [operating](32 to 122 deg. F)

40 to +70 deg. C [storage](-40 to +158 deg. F)

Humidity: 0 to 90% non-condensing

Elevation: -500 to +2800m above sea level

(derate max. ambient to +40 linearly at 3100m)

ARGUS TECHNOLOGIES 010-006-B1 Rev B Page 2 of 2

MANUAL ADDENDUM

FORM 954-010-10 - Add2.doc 2/5/98

P.1

Unit Description:

Applies to Manual P/N and Rev:

RSTs 010-016-B0 Rev A SDs 018-007-B0 Rev D

010-019-B0 Rev A 018-008-B0 Rev C

010-020-B0 Rev A 018-011-B0 Rev C

010-007-B0 Rev A 018-016-B0 Rev C

010-013-B0 Rev B

010-015-B0 Rev A RCS 030-527-B2 Rev P/A

010-006-B0 Rev A

010-002-B0 Rev B

010-023-B0 Rev A

010-008-B0 and B2 Rev A

RSMs 010-510-B2 Rev C 010-030-B2 Rev B

010-525-B2 Rev P/A 010-505-B2 Rev C

010-511-B2 Rev P/A 010-024-B2 Rev C

010-528-B2 Rev A 010-036-B2 Rev C

010-529-B2 Rev A 010-028-B2 Rev B

010-522-B2 Rev B 010-034-B2 Rev B

010-512-B2 Rev A 010-037-B2 Rev A

010-503-B2 Rev A 010-035-B2 Rev A

010-510-B2 Rev B 010-038-B2 Rev A

010-029-B2 Rev B 010-039-B2 Rev A

NOTE: THIS ADDENDUM SHEET IS TO BE INSERTED IN ALL OF THE ABOVE LISTED

PRODUCT MANUALS. THIS ADDENDUM REPLACES THE ADDENDUM

“ADDNEW.DOC” INCLUDED WITH DOCUMENT 022-000-C1.

EXPLANATION:

The market shift from vented or “wet cell” to valve regulated lead acid (VLRA) batteries has prompted Argus to

update its factory default settings to accomodate the requirements of these batteries.

The changes listed below are being implemented immediately as new factory default settings in all Argus power

products. However, as always, customer requested settings will take precedent over factory defaults.

This addendum is to accompany all new Argus user manuals. Questions about the new factory default settings

should be directed to our toll free 1-888-GO ARGUS Technical Support line.

TABLE 1-1: RSM/RST/RCS SYSTEMS (excluding RSM 48/7.5 and 24/15)

Function 12 volt systems (nom) 24 volt systems (nom) 48 volt systems (nom)

Float 13.5 27 54

Equalize 13.8 27.5 55

OVP 14.5 29 57

LVA 11 22 44

HVA 14 28 55.5

TABLE 1-2: RSM 48/7.5 and 24/15 (module) @ 25°C (77°F)

MANUAL ADDENDUM

FORM 954-010-10 - Add2.doc 2/5/98

P.2

Function 24 volt systems (nom) 48 volt systems (nom)

Float 27 54

TABLE 1-3: RSM 48/7.5 and 24/15 SUPERVISORY/CONTROL MODULE

Function 24 volt systems (nom) 48 volt systems (nom)

LVD 21 42

TABLE 1-4: SUPERVISORY/CONTROL SYSTEMS (SD-02,03,04,05)

Function 12 volt systems (nom) 24 volt systems (nom) 48 volt systems (nom)

Load Out 10.5 21 42

Load In 12.5 25 50

LVA 12 24 48

HVA 14 28 55.5

HVSD n/a 29.5 58

NOTE: THIS ADDENDUM SHEET IS TO BE INSERTED IN ALL OF THE ABOVE LISTED

PRODUCT MANUALS. THIS ADDENDUM REPLACES THE ADDENDUM “ADDNEW.DOC”

INCLUDED WITH DOCUMENT 022-000-C1.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for battery charger

models RST 48/50, 48/30, 24/50, 24/100, 12/50 & 12/100.

1. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. CAUTION - To reduce risk of injury, charge only lead-acid type rechargeable batteries.

Other types of batteries may burst causing personal injury and damage.

3. Do not expose charger to rain or snow.

4. Use of an attachment not recommended or sold by the battery charger manufacturer may re-

sult in a risk of fire, electric shock, or injury to persons.

5. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualified service center.

6. Do not disassemble charger; take it to a qualified service center when service or repair is re-

quired. Incorrect reassembly may result in a risk of electrical shock or fire.

INSTALLATION AND OPERATOR’S MANUAL FOR RST SERIES OF SWITCHED MODE RECTIFIERS

Table of Contents

Section Topic Page

1.0 Warranty

2.0 Documentation & Part Numbers ...................................... 1

2.1 Introduction .............................................. 1

2.2 ARGUS numbering system ................................... 1

3.0 General ....................................................... 2

3.1 Scope .................................................. 2

3.2 Introduction .............................................. 2

3.3 Features ................................................ 2

4.0 Installation Instructions............................................. 7

4.1 Tools Required............................................ 7

4.2 Inspection ............................................... 7

4.3 Preparation/Mounting ....................................... 7

4.4 Input Connections.......................................... 8

4.5 Output Connections ........................................10

4.6 Initial Start-up.............................................12

5.0 Operating Instructions .............................................15

5.1 Shut-down ...............................................15

5.2 Start-up ................................................15

5.3 Normal mode .............................................15

5.4 Float/equalize/test..........................................15

5.5 Fuse replacement..........................................15

6.0 Adjustments ....................................................16

6.1 Factory Settings/Ranges .....................................16

6.2 Current Limit .............................................16

6.3 Float Voltage .............................................17

6.4 Equalize Voltage ..........................................17

6.5 Test Voltage..............................................17

6.6 Output Slope/Parallel Operation................................18

6.7 Start Delay...............................................19

6.8 Over Voltage Protection .....................................19

6.9 Under Voltage Alarm .......................................19

7.0 Theory of operation ...............................................21

7.1 Power Circuit .............................................21

7.2 Control Circuit ............................................21

8.0 Schematics/Parts Lists.............................................29

9.0 Trouble shooting and Repair ........................................30

9.1 Diagnostic chart ..........................................30

10.0 Moving and Storage ..............................................34

Warranty Policy

Argus Technologies Ltd. warrants all equipment manufactured by it to be free from defects in parts

and labor, excluding third party OEM materials (example: air conditioners, batteries), for a period of

two years from the date of shipment from the factory. For third party products the OEM’s warranty

shall apply. The liability of Argus applies solely to repairing, replacing or issuing credit (at Argus’ sole

discretion) for any equipment manufactured by it and returned by the customer during the warranty

period. The terms of the warranty are Ex Works (EXW) from Argus’ factory service location.

Argus reserves the right to void the warranty if:

(1) identiﬁcation marks or serial numbers are removed or altered in any way,

(2) invoice is unpaid, or

(3) defect is the result of misuse, neglect, improper installation, environmental

conditions, non-authorized repair, alteration or accident.

Argus shall not be liable to the customer or other parties for any loss of proﬁts, loss of use, costs for

removal or installation of defective equipment, damages or consequential damages based upon

equipment failure during or after the warranty period. There shall be no other obligations either

expressed or implied. Argus will not honor warranties for batteries and other third party products

without prior written Argus authorization.

Freight Policy

Customer is responsible for all shipping and handling charges (COD and freight collect will not be

accepted without prior approval from Argus Technologies).

Terms of Payment (North America)

Payment terms are net 30 days subject to prior credit approval. All other orders require payment

before shipping.

Terms of Payment (International)

Payment terms are subject to prior approval and are typically through Tele-Transfer.

Return Material Policy

Our RMA policy is designed to ensure prompt, efﬁcient and high quality factory service. A Return

Material Authorization (RMA) number must be obtained before products can be accepted for

servicing by the Argus factory. For returns to an authorized service center (refer to “Authorized

Service Centers” for locations), please consult the individual service center for speciﬁc return policies

and instructions.

To obtain a RMA number for a factory return, customers must call the appropriate location with the

product serial and model number, as well as a brief description of the problem, shipment instructions

and billing details.

The original packing container should be used whenever possible. Both the shipping documents

and the outside of the box must have the RMA # clearly marked and the product shipped prepaid to

the Argus factory service center. Argus will endeavor to repair products within ﬁve working days of

receipt. Repairs to the returned product are warranted for a period of six months. A service charge

may be applied if no fault is found in the returned product. Argus will not accept products without an

RMA number.

Business Hours

Argus North American ofﬁce hours are 7:30 am to 5:00 pm (Paciﬁc Standard Time) Monday to Friday.

WARRANTY AND REPAIR INFORMATION

Canada and USA toll free 24 hour emergency technical support: +1 888 GO ARGUS (462 7487) Outside North America: +1 604 436 5547

Factory Service Centers

Canada and International

Argus Technologies Ltd.

ATTN: RMA Returns

7033 Antrim Avenue

Burnaby, BC, V5J 4M5 Canada

Tel: +1 604 436 5900

Fax: +1 604 436 1233

Email: returns@argusdcpower.com

USA

Argus Technologies Inc.

ATTN: RMA Returns

3116 Mercer Avenue

Bellingham, WA, 98225 USA

Tel: +1-360 756 4904

Fax: +1-360 647 0498

Email: returns-usa@argusdcpower.com

Asia-Paciﬁc

PCM Electronics (Dong Guan) Co., Ltd.

Hongli Industrial Area, Miaobian, Liaobu Town,

Dongguan City, Guangdong Province,

523400 China

Tel: +86 755 8895 3310

Fax: +86 755 8895 3307

Authorized Service Center

Argentina

Argus Technologies de Argentina

Belen 315, Capital Federal, Buenos Aires,

1407l Argentina

Tel: +54 (11) 4672 4821

Fax: +54 (11) 4504 4698

Cell: +54 9 (11) 4993 9996

Email: [email protected]

Asia

Argus Technologies Asia Pte Ltd

Blk 6 Tagore Lane #160

Singapore 787570

Tel: +65 6458 8900

Fax: +65 6458 2122

Australia

CPS National

8/376 Newbridge Rd

Moorebank, NSW, 2170 Australia

Tel: +61 02 9822 8977

Fax: +61 02 9822 8077

Australia/New Zealand

Alpha Power Systems Pty Ltd

Unit 3, 30 Heathcote Road

Moorebank, NSW, 2170 Australia

Tel: +61 02 9602 8331

Fax: +61 02 9602 9180

Century Yuasa

37 - 65 Colbalt Street

Carole Park QLD 4300

Australian Sales & Service

Tel: +61 07 3361 6587

Fax: +61 07 3361 6705

New Zealand Sales & Service

Tel: +64 9 978 6689

Fax: +64 9 978 6677

Canada

Compower Systems Inc.

118 Tifﬁeld Road

Toronto, ON, M1V 5N2 Canada

Tel: +1 416 293 3088

Fax: +1 416 293 0671

Europe

Alpha Technologies Europe Ltd.

Cartel Business Estate

Edinburgh Way

Harlow, Essex, CM20 2DU UK

Tel: +44 1279 422110

Fax: +44 1279 423355

Mexico & Central America

Technologies Argus First De Mexico SA de CV

Anatole France No. 17

Col. Polanco

Mexico City, 11560 Mexico

Tel: +52 55 5280 6990

Fax: +52 55 5280 6585

South America

Argus Technologies Argentina

Santo Tome 2573, Capital Federal

Buenos Aires, 1416 Argentina

Tel: +54 11 4504 4698

Cell: +54 9 11 4993 9996

E-pager: [email protected]

Turkey

IPC Enerji Elk San ve TIC AS

Inonu cad. Kanarya sok. No:20

Yenisahra - Kadikoy

Istanbul, Turkey

Tel: +90 216 317 41 42

Fax: +90 216 472 90 66

048-507-10-I1 Rev S (09/2007)

Inhaltsverzeichnis

Andere Argus Stromversorgung Handbücher

Argus

Argus RGB-500 II Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung