Arlec DC687 Bedienungsanleitung

5 6

Introduction

The Wireless Door Chime (DC687)

consists of two separate units:-

1. Push Button Unit

(Transmi t ter)

2. Chime Unit

(Receiver)

These units are completely

self-contained and no wiring between

them is necessary.

Range

Up to 100 metres.

NOTE: Range depends on location,

temperature, and battery condition.

Socket Outlet Output

230-240v a.c. 10amp 2400w max.

6. Clean only with a damp cloth and mild detergent. Do not use solvents.

7. In an event of power outage, surge or unstable main power supply,

your door chime will default to factory setting. Please reset the unit

according to ‘Resetting the Unit’.

Security

When you are away from home for long periods you may wish to leave

your Chime Unit with one of your neighbours so that they can monitor

callers to your house during your absence.

Trouble Sooting & User Hints

Problem Possible Cause Suggested Remedy

Chime does

not sound.

1. Units are out of range

(max. range 100m).

Operate the Chime unit within the

operation range (100m).

2. Push Button and Chime

units are not on same

frequency coding.

Re-set the frequency coding

(see Code Selection) or select a

different tone (see Tone Selection).

3. Flat Push Button battery. Change the battery.

4. Wrong polarity of bat tery

in Push Button.

Re-insert battery with polarity to

match markings.

5. Power outage, surge or

unstable main power

supply.

Re-set unit according to

‘Resetting the Unit’

Chime sounds

without Push

Button being

pressed

1. A power interruption

to the Door Chime unit

plus a similar door chime

product operating nearby

has caused the chime unit

to reset to the incorrect

House Code

A. Switch off the Chime Unit for at

least 1 minute. Switch on again.

It should beep twice. Press

the Push Button to operate the

chime. This re-sets the House

Code in the Chime Unit or;

B. Re-set the frequency coding

(see Code Selection

2. A similar Wireless

Door Chime product is

operating nearby on the

same House Code

Re-set the House Code

(see Code Selection).

3. Interference from CBs,

Taxis or remote control

toys operating on the

same frequency.

Re-set the House Code

(see Code Selection).

Warranty

Arlec guarantees this product in accordance with the Australian Consumer Law.

Arlec also warrants to the original ﬁrst purchaser of this product (“you”) from a retailer that

this product will be free of defects in materials and workmanship for a period of 12 months

from the date of purchase; provided the product is not used other than for the purpose,

or in a manner not within the scope of the recommendations and limitations, speciﬁed by

Arlec, is new and not damaged at the time of purchase, has not been subjected to abuse,

misuse, neglect or damage, has not been modiﬁed or repaired without the approval of

Arlec and has not been used for commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your own expense, return the product,

and provide proof of original purchase and your name, address and telephone number,

to Arlec at the address below or the retailer from whom you originally purchased the

product within 12 months from the date of purchase.

Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in

the above manner and if, in Arlec’s reasonable opinion, the Warranty applies, Arlec will

at its own option and expense (or authorise the retailer to) replace the product with the

same or similar product or repair the product and return it to you or refund the price you

paid for the product. Arlec will bear its own expenses of doing those things, and you must

bear any other expenses of claiming on the Warranty.

The Warranty is in addition to other rights and remedies you may have under a law in

relation to the product to which the Warranty relates.

Our goods come with guarantees that cannot be excluded under the Australian Consumer

Law. You are entitled to a replacement or refund for a major failure and for compensation

for any other reasonably foreseeable loss or damage. You are also entitled to have the

goods repaired or replaced if the goods fail to be of acceptable quality and the failure

does not amount to a major failure.

Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.

Arlec’s telephone number, address and email address are:

Customer Service: (03) 9982 5111

Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130

Email: [email protected]

CPIN002309

Plug-In Wireless Door Chime

with Power Socket

DC687

Installation & Operating

Instructions

CPIN002309

DC687_CPIN002309.indd 1-3 30/03/12 4:00 PM

Code/Push Button Limiting Switch

Your Chime Unit is capable of working with a maximum of 4 Bell

Push Button units, each with its own frequency. If your Chime

Unit activates intermittently for no apparent reason, it might be

caused by a nearby device working on a similar frequency channel.

To eliminate frequency channel interruption, use the Code/Push

Button Limiting Switch (Fig. 3) to limit the Bell Push Button unit

and/or frequency channel that your Chime Unit can be activated by.

1. Connect the Chime Unit to the mains power and press

the Bell Push Button once. The Chime Unit will sound

to indicate that the 1st operating code is registered and

memorised. This is the factory setting and intended to limit

the active frequency channel and Bell Push Button unit to 1.

2. To register a 2nd Bell Push Button, press and hold the

Code Limiting Switch on the Chime Unit for 1 second, a ‘beep’ will sound

to indicate that it is ready to learn the 2nd operating code. Press the 2nd

Bell Push Button once, the Chime Unit will sound to indicate that the 2nd

operating code is registered and memorised. This will allow 2 different Bell

Push Button units and/or frequency channels to work with the Chime Unit at

the same time.

3. Repeat Step 2 to add a 3rd and 4th Bell Push Button.

4. To reset, disconnect the Chime Unit from mains power for at least 1 minute

then reconnect. This will reset the Chime Unit to learn 1 Push Button

and/or frequency channel only.

Note: Power outage, surge or unstable main power will also reset the

Code/Push Button Limiting function.

Resetting the Unit

To avoid uncontrolled activation:

1. Switch off the Chime Unit for at least 1 minute.

2. Switch back on. A double beep should be heard indicating that the unit is in

learning mode.

3. Press the Push Button. The chime should sound to indicate code selection.

Important Notes

1. The operation and range of your Wireless Door Chime depends on location,

temperature and battery condition.

2. Try different locations in your home, ideally more than 1 metre from the ﬂoor.

Move Chime unit closer to Push Button unit to improve operation.

3. Do not expose either unit to rain or immerse in water.

4. Avoid locations where the Push Button unit is exposed to direct summer

sunlight.

5. Do not leave exhausted batteries in Push Button unit.

432

Push Button

1. Push Button unit is operated by 1 x 3 volt Lithium battery (CR2032 - included).

2. Remove the back of case by pushing in the tab on the bottom with a small,

ﬂat screwdriver.

3. The 3 volt Lithium battery (CR2032) is already installed.

Simply pull off the isolation strip which will allow the battery to make electrical

contact.

To Replace the Battery

Remove the locking screw from the battery holder clip and remove

old battery.

Insert 1 x 3 volt Lithium battery (type CR2032) in the battery

compartment, ensuring the battery polarity is correct as in Fig.1.

Replace clip and tighten locking screw to hold battery ﬁrmly in

place.

Chime Unit

The Chime Unit is powered by 240 volt and should be plugged into

any convenient household power point.

INSTALLATION

Chime Unit

Plug the Chime Unit into any household power point and switch power on. The

Chime Unit indicator lamp will glow and it will beep twice to indicate it is ready.

Press the push button unit to test the chime.

Do not mount the chime unit near metal objects, security door or in close

proximity to any radio emitting equipment. The range of the unit may be

substantially reduced.

Push Button Unit

The Push Button unit has two mounting holes on rear plate of unit that must be

pushed through before unit can be mounted.

1. Remove rear plate of unit (see battery installation).

2. Push through tabs in mounting holes.

3. Using the back plate of the Push Button unit as a guide, mark the position of

holes onto mounting surface.

4. Drill appropriately sized holes and insert wall plugs if required.

5. Secure the back plate of Push Button unit to mounting unit.

6. Clip Push Button unit to back plate.

Alternatively the Push Button unit can be attached to smooth mounting

surfaces such as painted wood, glass and plastic using Self-Adhesive Pad

(supplied).

Do not mount the push button unit on metal or near metal door frame, security

door, metal furniture or in close proximity to any radio emitting equipment. The

range of the unit may be substantially reduced.

Door Chime Operation

Once the Push Button and Chime units have been installed in their desired

locations, the system is ready for use.

Depress button on Push Button unit momentarily, and chime should sound.

Press button again to repeat. Continual pressing of the button will not repeat

the chime.

If chime fails to sound, check batteries in push button and check power is on to

Chime Unit.

Tone Selection

The Wireless Door Chime is supplied with 8 built-in chimes.

Westminster Chime Twinkle Twinkle

Double Ding-Dong It’s a Small World

Circus Theme Dog Barking

Banjo on My Knee Telephone Ring

To change the chime tune, remove the Push Button Unit’s rear

cover.

Inside the Push Button Unit locate the small Tune Selector push

button marked ‘S’ (Ref. Fig 2). Each time that this Tune Selector

push button is pressed, the next of the 8 melodies will be played.

You can step through and listen to each in turn. When you hear

the melody you wish to choose, do not press the tune selector

again. The chime will play the selected melody each time the

bell press is pushed. At any time you can select another melody

by repeating the tune selector button process.

Reﬁt the Push Button Unit rear cover.

Whenever the Push Button Unit battery is ﬁtted or replaced, the

chime tune may default to the Westminster Chime.

Code Selection

The push button unit generates random code sequences to which the chime

unit is able to learn. Should your door chime unit activate intermittently for no

apparent reason, the uncontrolled activation may be caused by another unit

nearby or from a device operating on the same frequency.

Fig 1.

Fig 2.

Fig 3.

Code

Limiting

Switch

CPIN002308

DC687_CPIN002309.indd 4-6 30/03/12 4:00 PM

Inhaltsverzeichnis

Andere Arlec Gegensprechanlage Handbücher

Arlec

Arlec DC681 Handbuch

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung