Armodilo Xero Bedienungsanleitung

Tablet alignment

start here

Adding your tablet The kickstand Cleaning & care

E E

* The corner tabs are attached

to at the factory. Please do not

remove these or adjustments may

be necessary (See Tablet Alignment).

01 Set the tablet into the corner tabs

02 Combine , and optionally

aligning the edges together on all sides

03 Align the combined parts over the

corner tab holes

04 Insert pins in locations shown to temporarily

hold the combined parts in place

05 Thread 4x into to secure

the two front pieces over the tablet

starting with the two holes without pins

Adding the tablet

Your Xero tablet holder is made of various parts which may require

cleaning from time to time. Please dissasemble and remove the

tablet before using any liquids to clean the holder.

Clean using a slightly damp, lint free cloth (a mild dish soap and water

solution can be used to dampen cloth). Lightly wipe any surface to

remove dust or dirt. Do not apply too much pressure when wiping

to prevent scratching of the acrylic parts.

CAUTION: Never clean acrylic parts using alcohol or solvents as

they can destroy the acrylic and cause it to crack.

The Xero tablet holder was designed to work with a kickstand if used

on it’s own to provide the perfect viewing angle. The kickstand comes

standard with solo Xero purchases and can be purchased as an add-on

when purchasing a Xero stand combo. It works in either landscape or

portrait mode and can easily be reconﬁgured, simply follow these steps:

1. Gently squeeze the kickstand from the sides to

compress it slightly towards the center of the Xero

2. The kickstand, once squeezed can be removed

and reoriented into another set of mounting holes

3. Align one side of the kickstand into a set of mounting

holes. Gently squeeze to compress the kickstand

and get the other side into place.

Do not over compress the kickstand or permanant damage may occur. The corner tabs that hold the tablet in place are designed to be

adjustable and can be turned. Very slight adjustments of these tabs

ensure a perfect tablet ﬁt. If for whatever reason your tablet no

longer sits perfectly, please follow these steps:

1. A set of lines along the side of each corner tab is added

at time of production to indicate proper alignment.

(Shown in red for sample purposes only.)

2. Check to ensure the corner tabs all line up with these

indicator marks. They should be parallel to each other.

3. If they do not, loosen the rear screw on the ‘X’ backer

and realign the tab back to the indicator mark.

4. Retighten to align the tab positioning. ✘✓

Properly

aligned

Requires

adjustment

A B C

Insert temporary pins into locations

shown during setup to help hold the

various pieces in place

while assembling

In the box

A B C

E FG

Tilt Sphere Surface Curve Floor 3-in-1

Optional stands & stand hardware

Xero Front Face Xero Front Face Backer Printed Insert

Corner Tabs (attached to G)Xero ‘X’ Backer ArmoLock Screws & Driver

x 4 (+2 spare) Screws

x 1 Driver

x 4

x 1

x 1 Optional

Step #4

For additional

information,

support and

downloads visit

armodilo.com

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Slide over (from bottom)

03 Connect to using two screws

04 Connect to a flat surface or wall

05 Slide down and secure with screws

06 Insert your tablet

07 Cover Tablet with and

(Insert optional printed insert at this step )

08 Thread 4 ArmoLock Screws through

and into

Surface Assembly

Step #3

Surface

Step #1

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Insert your tablet

03 Cover Tablet with and

(Insert optional printed insert at this step )

04 Thread 4 ArmoLock Screws through

and into

Curve Assembly

Step #4

Step #8

Step #1

A B E

3-in-1

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Connect to turning 4 pre-threaded

screws counterclockwise gently

03 Connect to turning 4 pre-threaded

screws counterclockwise gently

04 Connect to turning 4 pre-threaded

screws counterclockwise gently

05 Connect to using 4 screws

ensure plastic feet are on the bottom

06 Connect to turning 4 pre-threaded

screws counterclockwise gently

07 Insert your tablet

08 Cover Tablet with and

(Insert optional printed insert at this step )

09 Thread 4 ArmoLock Screws through

and into

Floor Assembly

Desktop Assembly

Wall Mount Assembly

01 Start at Step 01

02 After Step 03, connect

to turning 4

pre-threaded screws

counterclockwise gently

03 Attach to

using 2 screws

04 Attach to the wall

using 2 screws

Same as above, leaving out Step #03 & #04

Option 1: Option 2:

01 Start at Step 07

02 Use any standard

75 mm VESA

Mount to mount

the unit

to a wall

AB E

Curve

Step #5

Slide tubes onto

connectors, then

turn screws counter

clockwise to secure

screws into tube holes

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Connect to using four screws

03 Insert your tablet

04 Cover Tablet with and

(Insert optional printed insert at this step )

05 Thread 4 ArmoLock Screws through

and into

Floor Assembly

Floor

Step #2

Step #1

* If running cable –

put the cable through

tube ﬁrst, then complete

the assembly as noted

* If running cable –

put the cable through

tube ﬁrst, then complete

the assembly as noted

Step #09 (3-in-1)

Step #05 (Floor)

A B E

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Insert your tablet

03 Cover Tablet with and

(Insert optional printed insert at this step )

04 Put 4 ArmoLock Screws through

and into

Sphere Assembly

To permanently mount Sphere to a

surface follow the instructions below:

01 Screw in the two mounting thread inserts

that came supplied with the mounting kit

02 Drill holes in counter or surface*using

the mount pattern found online in

Support > Downloads

03 Set the Sphere with the mounting threads

into the drilled surface holes

04 Thread supplied washers and wing nuts onto

the mounting threads to secure the stand

*Surface depths up to 2.5"are supported

Optional Mounting

Step #4

Optional Mounting

Sphere

Step #1

CAUTION: Ensure enclosure is tilted

upwards when installing or removing security

screws to ensure tablet does not fall out.

WARNING: Ensure that the wall mount bracket

is mounted to a sturdy anchor point such as a

stud. Mounting the bracket to drywall is not

recommended as the force required to move

the tilt mechanism up or down can pull

mounting hardware out of weaker surfaces

such as drywall.

Tilt Assembly

01 Connect to using two screws

* Can be conﬁgured in either landscape or portrait mode

02 Insert your tablet (See caution below)

03 Cover Tablet with and

(Insert optional printed insert at this step )

04 Thread 4 ArmoLock Screws through

and into

05 Fasten to the wall using appropriate

bolts or screws*

06 Hang complete assembly onto

07 Tighten set screw at the base of

to secure Wall Mount to the bracket

Step #7

Step #4

Tilt

Step #5

READ WARNING

Step #1

A B E

Dieses Handbuch passt für folgende Modelle

Andere Armodilo Tablet-Zubehör Handbücher

Armodilo

Armodilo ALUR Bedienungsanleitung

Beliebte Tablet-Zubehör Handbücher anderer Marken

Thor’s Drone World

Thor’s Drone World Lifthor Mjolnir Bedienungsanleitung

EARTO

EARTO A1876 Bedienungsanleitung

Pyle

Pyle PSPADLK8 Bedienungsanleitung

MOB

MOB TUANUI Bedienungsanleitung

Logitech

Logitech Hinge Bedienungsanleitung

Bretford

Bretford PowerRack 10 Bedienungsanleitung

Brenthaven

Brenthaven EDGE 360 Bedienungsanleitung

Fujitsu

Fujitsu Stylistic 3400 Bedienungsanleitung

Heckler Design

Heckler Design WindFall STAND Bedienungsanleitung

Kensington

Kensington KeyFolio SecureBack Bedienungsanleitung

Xplore

Xplore Companion Keyboard Bedienungsanleitung

Logitech

Logitech Ultrathin Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA X MINI Bedienungsanleitung

Trust

Trust Executive Folio Stand Bedienungsanleitung

Manhattan

Manhattan 406017 Bedienungsanleitung

Logitech

Logitech SLIM COMBO Bedienungsanleitung

Logitech

Logitech AnyAngle iC1051 Bedienungsanleitung

Promate

Promate Dash.Mini Bedienungsanleitung