ARO MAC2650C Bedienungsanleitung
MAC1510C
MAC2010C
MAC2650C
MAC3550C
MOBILE LOCAL AIR CONDITIONER
REMOTE CONTROL ILLUSTRATION
1
CONTENTS
Remote controller Specications ..........................................................................................................2
Function buttons .....................................................................................................................................3
Handling the remote control...................................................................................................................4
Remote LED screen indicators ..............................................................................................................5
How to use the basic functions..............................................................................................................6
How to use the advanced functions ....................................................................................................12
WARRANTY............................................................................................................................................14
2
Remote Controller Specications
Rated Voltage 3V DC(2X1.5V); Typ:LR03(AAA)
Signal Receiving Range 8m
Environment -5°C~60°C
MAC1510C
MAC2010C
MAC2650C
MAC3550C
3
Function Buttons
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control.
The following is a brief introduction to the remote control itself. For instructions on how to operate your
air conditioner, refer to the How to Use Basic Functions section of this manual.
ON/OFF
Turns the unit on or off. SHORT CUT
Sets and activates your favorite
pre-settings.
TEMP
Increases temperate in 1°C
increments.
Max. temperature is 30 °C.
TEMP
Decreases temperate in 1 °C
increments.
Min. temperature is 17 °C.
NOTE: Press and hold
and buttons together for
3 seconds will alternate the
temperature display between
the °C & °F scale.
TIMER ON
Sets timer to turn unit on (see
How to Use Basic Functions
for instructions)
TIMER OFF
Sets timer to turn unit off (see
How to Use Basic Functions
for instructions)
SWING
Starts and stops louver
movement.
(MAC2650C, MAC3550C)
MODE
Scrolls through operation modes
as follows:
AUTO COOL DRY
HEAT FAN
NOTE: Heating function not
available for MAC1510C,
MAC2010C, MAC2650C,
MAC3550C.
FAN SPEED
Selects fan speeds in the
following order:
AUTO LOW MED HIGH
NOTE: MED
(only in MAC2650C, MAC3550C)
SLEEP
Saves energy during sleeping
hours LED
Turns indoor unit's LED display on
and off.
If you are sensitive to light when
you go to sleep, you can press
the LED button to turn off the LED
display on the unit. Press the
button again to turn it back on.
4
Handling The Remote Controller
NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and
How to Use Advanced Functions sections of
this manual for a detailed description of how to
use your air conditioner.
SPECIAL NOTE
ƔButton designs on your unit may differ slightly
from the example shown.
ƔIf the unit does not have a particular function,
pressing that function's button on the remote
control will have no effect.
ƔWhen there are wide differences
between "Remote control Illustration" and
"INSTRUCTION MANUAL" on function
description, the description of "INSTRUCTION
MANUAL" shall prevail.
Inserting and Replacing Batteries
Your air conditioning unit comes with two AAA
batteries. Put the batteries in the remote control
before use.
1. Slide the back cover from the remote Control
downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match
up the (+) and (-) ends of the batteries with
the symbols inside the battery compartment.
3. Slide the battery cover back into place.
BATTERY NOTES
For optimum product performance:
ƔDo not mix old and new batteries, or batteries
of different types.
ƔDo not leave batteries in the remote control,
if you don’t plan on using the device for more
than 2 months.
ƔNon-rechargeable batteries are not to be
recharged.
ƔExhausted batteries are to be removed from
the appliance and safely disposed of.
ƔThe supply terminals are not to be short
circuited.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal
waste. Refer to local laws for proper disposal of
batteries.
TIPS FOR USING REMOTE CONTROL
ƔThe remote control must be used within 8
meters of the unit.
ƔThe unit will beep when remote signal is
received.
ƔCurtains, other materials and direct sunlight
can interfere with the infrared signal receiver.
ƔRemove batteries if the remote will not be
used more than 2 months.
5
Remote LCD Screen Indicators
Heat
Transmission Indicator
Lights up when remote sends
signal to unit
MODE display
Displays the current mode,
including:
ƔAUTO
ƔCOOL
ƔDRY
ƔHEAT
ƔFAN
ON/OFF display
Appears when the unit is turned on, and disappears
when it is turned off
TIMER ON display
Displays when TIMER ON is set
TIMER OFF display
Displays when TIMER OFF is set
Battery display
Low battery
detection
SLEEP display
Displays when
SLEEP function is
activated
Temperature/Timer display
Displays the set temperature by default, or timer setting when using TIMER
ON/OFF functions
ƔTemperature range: 17-30 °C
ƔTimer setting range: 0-24 hours
This display is blank when operating in FAN mode.
FAN SPEED display
Displays selected FAN SPEED:
HIGH, MED, or
LOW
This display is blank when set to AUTO
speed.
NOTE: MED (only in MAC2650C,
MAC3550C)
Heating function not available for
MAC1510C, MAC2010C, MAC2650C,
MAC3550C.
6
How To Use The Basic Functions
COOL operation
1. Press the MODE button to select COOL mode.
2. Set your desired temperature using the Temp
or Temp button.
3. Press the FAN button to select the fan speed:
AUTO, LOW, MED, or HIGH.
4. Press the ON/OFF button to start the unit.
SETTING TEMPERATURE
The operating temperature range for units is 17-
30 °C. You can increase or decrease the set
temperature in 1 °C increments.
AUTO operation
In AUTO mode, the unit will automatically select
the COOL, FAN, HEAT or DRY mode based on
the set temperature.
1. Press the MODE button to select Auto mode.
2. Set your desired temperature using the Temp
or Temp button.
3. Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be set in Auto mode.
7
How To Use The Basic Functions
FAN operation
1. Press the MODE button to select FAN mode.
2. Press FAN button to select the fan speed:
AUTO, LOW, MED or HIGH.
3. Press the ON/OFF button to start the unit.
NOTE: You can’t set temperature in FAN mode.
As a result, your remote control’s LCD screen will
not display temperature.
DRY operation (dehumidifying)
1. Press the MODE button to select DRY mode.
2. Set your desired temperature using the Temp
or Temp button.
3. Press the 212)) button to start the unit.
NOTE: FAN SPEED can’t be changed in DRY
mode.
8
Setting the TIMER function
Your air conditioning unit has two timer-related
functions:
TIMER ON- sets the amount of timer after
which the unit will automatically turn on.
TIMER OFF- sets the amount of time after
which the unit will automatically turn off.
TIMER ON function
The TIMER ON function allows you to set a period
of time after which the unit will automatically turn
on, such as when you come home from work.
1. Press the TIMER ON button. By default,
the last time period that you set and an "h"
(indicating hours) will appear on the display.
Note: This number indicates the amount of
time after the current time that you want the
unit to turn on. For example, if you set TIMER
ON for 2 hours, "2.0h" will appear on the
screen, and the unit will turn on after 2 hours.
2. Press the TIMER ON button repeatedly to set
the time when you want the unit to turn on.
3. Wait 2 seconds, then the TIMER ON function
will be activated. The digital display on
your remote control will then return to the
temperature display.
Example: Setting unit to turn on after 2.5 hours.
9
TIMER OFF function
The TIMER OFF function allows you to set a
period of time after which the unit will automatically
turn off, such as when you wake up.
1. Press the TIMER OFF button. By default,
the last time period that you set and an "h"
(indicating hours) will appear on the display.
Note: This number indicates the amount of
time after the current time that you want the
unit to turn off.
For example, if you set TIMER OFF for 2
hours, "2.0h" will appear on the screen, and
the unit will turn off after 2 hours.
2. Press the TIMER OFF button repeatedly to set
the time when you want the unit to turn off.
3. Wait 2 seconds, then the TIMER OFF
function will be activated. The digital display
on your remote control will then return to the
temperature display.
Example: Setting unit to turn off after 5 hours.
NOTE: When setting the TIMER ON or TIMER
OFF functions, up to 10 hours, the time will
increase in 30 minute increments with each press.
After 10 hours and up to 24, it will increase in 1
hour increments. The timer will revert to zero after
24 hours.
You can turn off either function by setting its timer
to "0.0h".
Continue to press
TIMER ON or
TIMER OFF until
desired time is
reached.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Sprachen:
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
