Artel Fiberlink 7600 Series Bedienungsanleitung
Fiberlink®
7600 Series
HDMI® with Stereo Audio Transmission
over one single mode or multimode ber.
Artel Video Systems’Fiberlink® 7600 User’s Manual
Distribute HDMI® and stereo
audio over one single mode
or multimode ber with
no compression, scaling,
conversions or frame
dropping. The 7600 Series
is feature rich, including our
unique EDID function and
Pixel Clock phase selections.
World Headquarters
5B Lyberty Way
Westford MA 01886 USA
Tel: (978) 263-5775
Fax: (978) 263-9755
artel.com
Page 2 Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series Contents
Welcome ............................................................................3
Features .............................................................................3
Package Contents....................................................................3
Technical Specifications ..............................................................4
7600 Transmitter Specifications.......................................................4
HDMI® Specifications.................................................................4
Audio Specifications .................................................................4
7600 Transmitter Optical Specifications ...............................................5
7601 Receiver HDMI® Output .........................................................5
7601 Receiver Specifications .........................................................6
7600 General Specifications ..........................................................6
Installation Instructions ..............................................................7
EDID Functions ......................................................................8
EDID Functions (cont) ................................................................9
Operating Tips .......................................................................9
Video Adjust Switch..................................................................9
Using 9-Volt Battery ..................................................................9
Alarm Switch Settings & Options ................................................... 10
Indicator LEDs ..................................................................... 11
Operating Pointers ................................................................. 12
Troubleshooting ................................................................... 12
Maintenance....................................................................... 13
Certifications ...................................................................... 13
Contents
Page 3Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
Welcome
Thank you for purchasing Artel Video Systems’ Fiberlink® 7600 Series. The 7600 Series is
used to transmit pristine HDMI® with stereo audio over a single ber optic core. Compatible
with single mode or multimode ber, the 7600 is ideal for the most demanding of applica-
tions, from distance learning to rental and staging. The 7600 oers a unique EDID function
that allows you to generate EDID internally, or you can capture and permanently store EDID
information.
Features
• Supports HDMI® resolutions up to 1920 x 1200 at 165 MHz pixel clock
and HDTV resolutions of 480p, 720p, 1080i, and 1080p
• Unique 0/180 degree pixel clock selection to compensate for HDMI® cable skew
• Supports embedded stereo audio from the HDMI® source
• Uses no compression, frame dropping, or scaling for crystal clear signals
• Only one ber used - no pixel skewing
• Supports EDID from internal generation, or capture and storage.
• Transmits signals over one single mode or multimode ber optic core.
• RoHS Compliant
Package Contents
• One Fiberlink® 7600 or 7601.
• This User’s Manual
Welcome | Features | Package Contents
Page 4 Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
7600 Transmitter Specications
Number of Inputs: One HDMI® up to 165MHz Pixel Clock
Connector: One female HDMI® type A with screw lock
Spatial Resolutions: 480i, 480p, 720p, 1080i, 1080p, 1920x1200p;
50, 59.94 and 60 Hz vertical refresh
Color Resolutions: 8-Bits per pixel; pixel-for-pixel sampling
HDMI® Embedded Audio: 2 channels
EDID: Ability to capture EDID from target monitor
or internal default resolutions
Color Space Support: 8-Bit RGB or YCrCb
Technical Specications
Technical Specications
Audio Specications
Number of Audio Channels 2, unbalanced
HDMI® Specications
HDCP: Compliant with High-bandwidth Digital
Content Protection (HDCP) using HDMI®
standards
HDMI® Version Support: Contact Factory
Page 5Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
7600 Transmitter Optical Specications
Emitter Type FP Laser
Operating Wavelength 1310nm Optimal
Optical Fibers SM: 8-10/125 microns;
MM: 50u or 62.5u
Optical Connector ST
Class I Laser Product complies with FDA performance standard for laser products,
Title 21, Code of Federal Regulations, Sub-Chapter J.
Technical Specications
Technical Specications
7601 Receiver HDMI® Output
Number of Outputs 1
Connector One Female HDMI® type A with screw lock
Spatial Resolutions: 480i, 480p, 720p, 1080i, 1080p, 1920x1200p; 50,
59.94 and 60 Hz vertical refresh
Color Resolution: 8 bits per pixel; pixel-for-pixel sampling
HDMI® Embedded Audio: 2 channels
Color Space Support: 8-Bit RGB or YCrCb
HDCP: Compliant with High-bandwidth Digital
Content Protection (HDCP) using HDMI®
standards
Page 6 Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
7601 Receiver Specications
Connector ST
Wavelength 1100 - 1620 nm
Minimum Input Sensitivity -17 dBm
Maximum Input Power 0 dBm
Link Budget with 7600 Transmitter: 0-14 dB
Fiber Optic Input
Technical Specications
LED Indicators Power, Video, Audio,
Alarm (Card Version Only)
Box Version Dimensions 6.5w x 1.15h x 8l (in)
165 W x 29 H x 203 L (mm)
Weight 1 lb. (0.455 kg)
MTBF 32,000 hours
Power 9-24 volts, AC or DC,
7600: 5.3 watts, 18.0 BTU/Hr
7601: 4.7 watts, 16.0 BTU/Hr
Operating Temperature -10º C to +45º C
7600 General Specications
Page 7Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
The Fiberlink® 7600 Series of ber optic transmission system is ready for
immediate use and does not require any special tools or equipment. However, an Optical
Power Meter, such as the Fiberlink® 6650, can be useful in determining optical loss budgets
during your system’s design and system maintenance.
The following instructions describe the typical installation procedure:
1) Connect the HDMI® video source to the video input HDMI® connector on the
transmitter unit.
2) Determine your EDID requirements and follow the procedures described in the
“EDID Function” section of this manual.
3) Connect the video output on the receiver unit to the HDMI® monitor or load.
4) Connect the ber optic cable between the two Fiberlink units.
5) Apply power to both the Fiberlink units.
For box versions using DC power connections, refer to Figure 1.
6) When power is applied, the green POWER LED will light, indicating the presence
of operating power. The VIDEO LED will give an indication as described on page 13.
The green AUDIO LED will give an indication as stated on page 13.
7) The system should now be operational.
Note: The transmitter and receiver will each perform HDCP authentication with their source and
load. This will take several seconds to accomplish proper authentication.
Note: The Rack Card version has an additional red LED for indicating the presence of an alarm
condition (loss of signal). Refer to Indicator LED’s and Alarm Switch Settings & Options sections
of this manual.
Installation Instructions
The transmitting element in the Fiberlink® 7600 transmitter
unit contains a solid state Laser Diode located in the optical
connector. This device emits invisible infrared electromag-
netic radiation which can be harmful to human eyes. The ra-
diation from this optical connector, if viewed at close range
with no ber optic cable connected to the optical connector,
may be sucient intensity to cause instantaneous dam-
age to the retina of the eye. Direct viewing of this radiation
should be avoided at all times!
Installation Instructions
Page 8 Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
Installation Instructions (cont.)
Installation Instructions | EDID Function
Figure 1:
Power Connector
DC Input Polarity
9-24 Volts
AC or DC
(+) Positive
( - ) Negative
The Fiberlink® 7600 Series of HDMI® ber optic transmission system has a unique“EDID”
feature set that allows the capture and storage of EDID information, or allows the genera-
tion of the EDID internally, on-the-y. The procedures for implementing each feature are
described below.
Generating EDID internally when no EDID has been captured:
The 7600 Transmitter comes programmed from the factory with generic EDID data. If no
external EDID data is captured, this default EDID set will be used and presented to the HDMI®
source.
Capturing and storing EDID information:
1) Power o your source and the 7600 Series transmitter.
2) Connect a display to the 7600 HDMI® Input
3) Power on the display.
4) Power on your 7600 Transmitter unit.
5) Press and hold for approximately 3 seconds the‘Capture EDID’ button on the Transmitter
front panel.
The Video LED will ash, indicating the capture is in progress. Note that any previously
stored EDID information will be overwritten.
6) When the Video LED remains o, the capture is complete.
NOTE: Performing EDID capture with an HDMI® source connected to the 7600 will not result
in damage, nor will the EDID be successfully copied.
NOTE: This procedure will erase any previously stored EDID information, but not the fac-
tory default.
EDID Functions
Page 9Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
Resetting back to factory defaults when EDID has been previously stored:
1) Power o the 7600 Series transmitter
2) Disconnect any display from the 7600 HDMI® input
3) Power on your 7600 Transmitter unit.
4) Press and hold for approximately 3 seconds the‘Capture EDID’ button to erase stored EDID
information.
5) The Video LED should ash for conrmation.
EDID Function
Operating Tips
Video Adjust Switch
On the front panel of both the transmitter and the receiver is the VIDEO ADJ (adjust) Switch.
In some installations, due to the length or quality of the HDMI® cable being used, it may be
necessary to use the opposite phase of the pixel clock to clock the HDMI® data into the trans-
mitter or into the monitor from the receiver.
If you experience color distortion on vertical edges of the video image, use the opposite set-
ting of the switch on either the transmitter or the receiver or both.
Using 9-Volt Battery
The 7600 transmitter unit can be temporarily powered using a 9V battery making it very easy
to bring the transmitter to a ceiling mounted projector for EDID capture and storage!
If you receive unexpected display results, you may be operating the 7600 using EDID informa-
tion that was stored during a previous installation. Try clearing any stored EDID information.
EDID Functions (cont)
Page 10 Fiberlink® 7600 Series User’s Manual
Fiberlink® 7600 Series
Alarm Switch Settings for the Transmitter and Receiver Card
Switch Position Alarm Indication On O
1 Loss of HDMI® Signal Enabled Disabled
2 N/A N/A N/A
Alarm Switch Settings & Options
The Rack Card version of this product has an additional red indicator LED that illuminates
when an alarm condition exists.
The rack card unit also provides an output to drive a model 6020 Alarm Sensing Module
which provides an audible tone and activates a set of contacts for external signaling
purposes.
Alarm Switch Settings & Options
Single Mode or
Multimode Fiber
HDMI® Source 7600 Tx 7601Rx
Typical Application Diagram
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Artel Sicherheitssystem Handbücher
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung