Artesyn MVME2500-ECC Bedienungsanleitung

MVME2500-ECC

Quick Start Guide

P/N:6806800L02B (August 2014) Observe ESD-safe

measures

What’s in the box?

Install the RTM

When installing or servicing the

module or accessories, strictly

observe the safety precautions

in the Safety Notes Summary.

Otherwise, personal injury or

property damage may occur.

• Use either a properly grounded ESD

wrist strap or make sure that you are

working in an ESD-safe environ-

ment.

• Connect to the ESD connector at the

front or the rear of the system.

Make sure you receive all items of

your shipment:

• One MVME2500-ECC VMEbus

board

• One printed copy of Quick Start

Guide

• One printed copy of Safety Notes

Summary

• Other items that were ordered

Prepare the installation

site

• For information on the environmen-

tal and power requirements, see the

MVME2500-ECC Installation and Use

manual.

• Operating temperatures refer to the

temperature of the air circulating

around the blade and not to the

actual component temperature.

1. Power down all equipment and discon-

nect the power cable from the AC

power source.

2. Remove the chassis cover.

3. Remove the filter panel(s) from the card

slot(s) at the rear of the chassis (if the

chassis has a rear card cage).

4. Install the top and bottom edge of the

transition module into the rear guides

of the chassis.

5. Ensure that the levers of the two injec-

tor/ejectors are in the outward posi-

tion.

6. Slide the transition module into the

chassis until resistance is felt.

7. Move the injector/ejector levers in an

inward direction.

8. Verify that the transition module is

properly seated and secure it to the

chassis using the two screws adjacent

to the injector/ejector levers.

9. Connect the cables to the transition

module.

MVME2500-ECC-Quick Start Guide

Artesyn Embedded Technologies

Marketing Communications

2900 S. Diablo Way, Suite 190

Tempe, Arizona 85282

Artesyn Embedded Technologies

Lilienthalstr. 17-19

85579 Neubiberg/Munich

Germany

Finding more information

For more information on the product, see

the MVME2500-ECC Installation and Use and

other related documentation.

Visit our Web site http://www.arte-

syn.com/computing. Use SUPPORT>TECH-

NICAL DOCUMENTATION link to look for

technical documentation.

Technical Assistance

To request technical assistance, visit our

Web site http://www.artesyn.com

Install the board6

1. Attach an ESD strap to your wrist. Attach

the other end of the strap to an electrical

ground. Make sure that it is securely fas-

tened throughout the procedure

2. Remove VME filler panels from the VME

enclosures, as appropriate.

3. Install the top and bottom edge of the

board into the guides of the chassis.

4. Ensure that the levers of the two injector/

ejectors are in the outward position.

5. Slide the board into the chassis until

there is resistance.

6. Simultaneously move the injector/ejec-

tor levers in an inward direction.

7. Verify that the board is properly seated

and secure it to the chassis using the two

screws located adjacent to the injector/

ejector levers.

8. Connect the appropriate cables to the

board.

9. To remove the board from the chassis,

reverse the procedure and press the red

locking tabs (IEEE handles only) to

extract the board.

Install the PMC/XMC

support

1. Remove the PMC/XMC filler plate from

the front panel cut-out.

2. Slide the front bezel of the PMC/XMC into

the cut-out from behind. The front bezel

of the PMC/XMC module will be flushed

with the board when the connectors on

the module align with the mating con-

nectors on the board.

3. Align the mating connectors properly

and apply minimal pressure to the PMC/

XMC until it is seated to the board.

4. Insert the four PMC/XMC mounting

screws through the mounting holes on

the bottom side of the board, and then

thread the four mount points on the

PMC/XMC. Tighten the screws.

5. Install the board into the appropriate

card slot. Make sure that the board is well

seated into the backplane connectors.

Do not damage or bend connector pins.

6. Replace the chassis or system cover.

7. Reconnect the system to the power

source and then turn on the system.

The MVME2500-ECC does not support hot

swap. Power off the slot or the system and

make sure that the serial ports and switches

are properly configured.

Andere Handbücher für MVME2500-ECC

Andere Artesyn Einplatinencomputer Handbücher

Artesyn

Artesyn iVPX7225 RTM Kurzanleitung

Artesyn

Artesyn ATCA-7370 Kurzanleitung

Artesyn

Artesyn ATCA-7360 Kurzanleitung

Artesyn

Artesyn ATCA-7475 Kurzanleitung

Artesyn

Artesyn MVME51005E Kurzanleitung

Artesyn

Artesyn MVME2500 Series Bedienungsanleitung

Artesyn

Artesyn iVPX7225 RTM Bedienungsanleitung

Artesyn

Artesyn MVME2502 Kurzanleitung

Beliebte Einplatinencomputer Handbücher anderer Marken

WIN Enterprises

WIN Enterprises PL-80910 Bedienungsanleitung

AXIOMTEK

AXIOMTEK SBC81206 Series Bedienungsanleitung

Embest

Embest SOM-PH8800 Bedienungsanleitung

SeaLevel

SeaLevel SBC-R9 Bedienungsanleitung

SMART Embedded Computing

SMART Embedded Computing ATCA-8310 Bedienungsanleitung

WinSystems

WinSystems PPM-LX800-G Bedienungsanleitung

GIGAIPC

GIGAIPC QBiX-PPC Series Bedienungsanleitung

OLIMEX

OLIMEX A10S-OLinuXino-MICRO Bedienungsanleitung

Commell

Commell FS-978 Bedienungsanleitung

GIGAIPC

GIGAIPC QBiP-8665A/ Bedienungsanleitung

VersaLogic

VersaLogic Python EBX-11 Bedienungsanleitung

Micro Computer Specialists

Micro Computer Specialists IRV-3702 Bedienungsanleitung

CompuLab

CompuLab SB-A510 Bedienungsanleitung

Boser

Boser HS-7321 Bedienungsanleitung

Premier Farnell

Premier Farnell Embest SBC8530 Bedienungsanleitung

MicroSys Electronics

MicroSys Electronics miriac SBC-LS1043A2 Bedienungsanleitung

Aaeon

Aaeon UP Bedienungsanleitung

Portwell

Portwell WUX Series Bedienungsanleitung