Artila Matrix-510 Bedienungsanleitung
Matrix-510
Linux ARM9 Industry Box Computer
User Guide
Version 1.0
Copyright © Artila Electronics Co., Ltd. All Rights Reserved.
Table of Contents
1. Introduction................................................................................................................ 1
1.1 Packing List......................................................................................................................... 1
1.2 Optional Accessory............................................................................................................. 1
2. Layout......................................................................................................................... 2
3. Pin Assignment and Definition.................................................................................. 3
3.1 Reset Button ....................................................................................................................... 3
3.2 Power LED.......................................................................................................................... 3
3.3 Ready LED.......................................................................................................................... 3
3.4 Link / Act LED ..................................................................................................................... 3
3.5 Serial Port LED ................................................................................................................... 3
3.6 Ethernet Port....................................................................................................................... 3
3.7 Serial Port ........................................................................................................................... 3
3.8 Serial Console Port............................................................................................................. 4
3.9 Digital I/O Port (DB25 Female)........................................................................................... 5
3.10 Factory Default Settings...................................................................................................... 6
3.11 Network Settings................................................................................................................. 6
3.12 Wireless LAN Configuration................................................................................................ 6
3.13 File System ......................................................................................................................... 7
3.14 Devices List......................................................................................................................... 8
3.15 Utility Software.................................................................................................................... 8
4. Artila Utility Software................................................................................................. 9
4.1 update................................................................................................................................. 9
4.2 setuart................................................................................................................................. 9
4.3 lcdctl.................................................................................................................................... 9
4.4 gpioctl................................................................................................................................ 10
4.5 vplay.................................................................................................................................. 10
4.6 Tone.................................................................................................................................. 10
4.7 mp3play............................................................................................................................. 11
4.8 How to Make More Utility Software................................................................................... 11
4.9 Mounting External Storage Memory................................................................................. 11
4.10 Welcome Message ........................................................................................................... 11
4.11 Web Page Directory.......................................................................................................... 12
4.12 Adjust the System Time.................................................................................................... 12
4.13 SSH Console..................................................................................................................... 12
4.14 Install GNU Toolchain....................................................................................................... 13
4.15 Getting Started with the Hello Program ............................................................................ 13
Matrix-510 User Guide
‧1‧
1. Introduction
Matrix-510 is an ARM9-based Linux ready industrial computer. The key features are as follow:
ARM920T ARM Thumb Processor with 200MIPS at 180MHz, Memory Management Unit
16-KByte Data Cache and 16-KByte Instruction Cache
64MB SDRAM, 16MB Flash on board
Two 10/100Mbps Ethernet
Two USB 2.0 full speed (12Mbps) Host Ports
Multimedia Card Interface for SD memory card
Five 3-in-1 RS-232/422/485 ports and three RS-232 ports
21 programmable Digital I/O port
Audio Output
9 to 40VDC power input
Pre-installed Standard Linux 2.6 OS
GNU tool chain available on Artila FTP
Optional DIN RAIL mounting adaptor
1.1 Packing List
Matrix-510 Box Computer
Wall mount bracket
1.2 Optional Accessory
CB-RJ45F9-150 (91-R45F9-150): Serial Cable (RJ45 to DB9 Female, 150cm)
CB-RJ2CON-100 (91-RJCON-100): Console Cable (RJ45 to DB9 Female, 100cm)
DK-35A (36-DK35A-000): DIN RAIL Mounting Kit
Matrix-510 User Guide
‧2‧
2. Layout
25
12.5
4
167.5
5.9
104
36
1
10
Reset
Button
Matrix-510 User Guide
‧3‧
3. Pin Assignment and Definition
3.1 Reset Button
Press the “Reset” button to activate the hardware reset. You should only use this function if the
software does not function properly.
3.2 Power LED
The Power LED will show solid green if power is properly applied.
3.3 Ready LED
The Ready LED will show solid green if Matrix-510 complete system boot up. If Ready LED is off
during system boot up, please check if power input is correct. Turn off the power and restart
Matrix-510 again. If Ready LED is still off, please contact the manufacture for technical support.
3.4 Link / Act LED
When Ethernet port are connected to the network, Link/Act will show solid green and if there is traffic is
the Ethernet port, this LED will flash.
3.5 Serial Port LED
These eight dual color LEDs indicate the data traffic at the serial ports. When RXD line is high then
Green light is ON and when TXD line is high, Yellow light is ON.
3.6 Ethernet Port
Pin No.
Signal
1
ETx+
2
ETx-
3
ERx+
6
ERx-
3.7 Serial Port
Port 1, 5, 6, 7, 8: 3-in-1 RS-232 / 422 / 485
Port 2, 5, 6, 7, 8: RS-232 with full modem control
Note
RS-232 / 422 / 485 is software selection.
Matrix-510 User Guide
‧4‧
Pin No.
RS-232
RS-422
RS-485
1
DSR
--
-
2
RTS
TXD+
DATA+
3
GND
GND
GND
4
TXD
TXD-
DATA-
5
RXD
RXD+
--
6
DCD
RXD-
-
7
CTS
-
-
8
DTR
-
-
3.8 Serial Console Port
Serial console port share the connector with Serial port 3 but the pin definition as shown as follow:
Pin No.
RS-232
1
2
TXD
3
GND
4
5
6
7
RXD
8
The serial console port is disabled as factory default setting. To enable the serial console, you need
to use the serial console cable and connect it to port 3. Use any terminal software such as hyper
terminal and setting as follow:
Baud Rate: 115200
Data bits: 8
Parity: N
Stop bit: 1
Terminal type: ANSI
Right after powering on the system, keep typing $ continuously until you see the message as shown in
the figure followed. Console (ttyS0) stands for console port ttyS0 is enabled. Repeat this procedure
will disable the serial console and Screen will show “Console (null)”.
P3
Matrix-510 User Guide
‧5‧
3.9 Digital I/O Port (DB25 Female)
Pin No.
RS-232
Pin No.
Function
1
DIO0
14
DIO13
2
DIO1
15
DIO14
3
DIO2
16
DIO15
4
DIO3
17
DIO16
5
DIO4
18
DIO17
6
DIO5
19
DIO18
7
DIO6
20
DIO19
8
DIO7
21
DIO20
9
DIO8
22
GND
10
DIO9
23
GND
11
DIO10
24
VCC3
12
DIO11
25
VCC5
13
DIO12
Note
1. VCC3: 3.3 VDC output
2. VCC5: 5 VDC output
3. GND: Digital Ground
Matrix-510 User Guide
‧6‧
3.10 Factory Default Settings
LAN 1 IP Address: 192.168.2.127
LAN 2 IP Address: DHCP
Login: guest
Password: guest
Supervisor: root (ssh supported)
Password: root
3.11 Network Settings
To configure the IP address, Netmask and Gateway setting, please modify /disk/etc/rc as following:
ifconfig eth0 192.168.2.127 netmask 255.255.255.0
For DHCP setting:
dhcpcd eth1 &
3.12 Wireless LAN Configuration
Matrix-510 supports wireless LAN by using USB WLAN adaptor which uses Ralink RT2570 (rt2570)
/2571 (rt73) controller. Please refer to the website http://ralink.rapla.net for the supporting list of the
USB WLAN adaptor.
To configure the wireless LAN setting, please use command:
modprobe rt73 or modprobe rt2570
ifconfig wlan0 up
iwconfig wlan0 essid XXXX key YYYYYYYY mode MMMM
For infrastructure mode XXXX is the access point name and YYYYYYYY is the encryption key and
MMMM should be managed.
For Ad-Hoc mode mode XXXX is the Matrix-510 device name and YYYYYYYY is the encryption key
MMMM should be ad-hoc.
Inhaltsverzeichnis
Andere Artila Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
